Abstract: In the present study an attempt has been made to re-engineer traditional wadi into wholesome ready-to-use cereal-pulse-based chunks rich in protein quality and fibre content. Chunks were made using extrusion-dehydration combination. Two formulations i.e., whole green gram dhal with instant oats and washed green gram dhal with whole oats were formulated. These chunks are versatile in nature as they can be easily incorporated in day-to-day home-made preparations such as pulao, potato curry and kadhi. Cereal-pulse ratio was calculated using NDpCal%. Limiting amino acids such as lysine, tryptophan, methionine, cysteine and threonine were calculated for maximum amino acid profile in cereal-pulse combination. Time-temperature combination for extrusion at 130oC and dehydration at 65oC for 7 hours and 15 minutes were standardized to obtain maximum protein and fibre content. Proximate analysis such as moisture, fat and ash content were analyzed. Protein content of formulation was 62.10% and 68.50% respectively. Fibre content of formulations was 2.99% and 2.45%, respectively. Using a 5-point hedonic scale, consumer preference trials of 102 consumers were conducted and analyzed. Evaluation of chunks prepared in potato curry, kadi and pulao showed preferences for colour 82%, 87%, 86%, texture and consistency 80%, 81%, 88%, flavour and aroma 74%, 82%, 86%, after taste 70%, 75%, 86% and overall acceptability 77%, 75%, 88% respectively. High temperature inactivates antinutritional compounds such as trypsin inhibitors, lectins, saponins etc. Hence, availability of protein content was increased. Developed products were palatable and easy to prepare.
Abstract: Background: The incidence of adverse reactions to iodinated contrast media has risen. The dearth of reports on reactions to the administration of iso- and low-osmolar contrast media should be addressed. We, therefore, studied the profile of adverse reactions to iodinated contrast media; viz., (a) the body systems affected (b) causality, (c) severity, and (d) preventability. Objective: To study adverse reactions (causes and severity) to iodinated contrast media at Srinagarind Hospital. Method: Between March and July, 2015, 1,101 patients from the Department of Radiology were observed and interviewed for the occurrence of adverse reactions. The patients were classified per Naranjo’s algorithm and through use of an adverse reactions questionnaire. Results: A total of 105 cases (9.5%) reported adverse reactions (57% male; 43% female); among whom 2% were iso-osmolar vs. 98% low-osmolar. Diagnoses included hepatoma and cholangiocarcinoma (24.8%), colorectal cancer (9.5%), breast cancer (5.7%), cervical cancer (3.8%), lung cancer (2.9%), bone cancer (1.9%), and others (51.5%). Underlying diseases included hypertension and diabetes mellitus type 2. Mild, moderate, and severe adverse reactions accounted for 92, 5 and 3%, respectively. The respective groups of escalating symptoms included (a) mild urticaria, itching, rash, nausea, vomiting, dizziness, and headache; (b) moderate hypertension, hypotension, dyspnea, tachycardia and bronchospasm; and (c) severe laryngeal edema, profound hypotension, and convulsions. All reactions could be anticipated per Naranjo’s algorithm. Conclusion: Mild to moderate adverse reactions to low-osmolar contrast media were most common and these occurred immediately after administration. For patient safety and better outcomes, improving the identification of patients likely to have an adverse reaction is essential.
Abstract: In the current study, energy and exergy analysis of a 65 MW steam power plant was carried out. This study investigated the effect of variations of overall conductance of the super heater on the performance of an existing steam power plant located in Derna, Libya. The performance of the power plant was estimated by a mathematical modelling which considers the off-design operating conditions of each component. A fully interactive computer program based on the mass, energy and exergy balance equations has been developed. The maximum exergy destruction has been found in the steam generation unit. A 50% reduction in the design value of overall conductance of the super heater has been achieved, which accordingly decreases the amount of the net electrical power that would be generated by at least 13 MW, as well as the overall plant exergy efficiency by at least 6.4%, and at the same time that would cause an increase of the total exergy destruction by at least 14 MW. The achieved results showed that the super heater design and operating conditions play an important role on the thermodynamics performance and the fuel utilization of the power plant. Moreover, these considerations are very useful in the process of the decision that should be taken at the occasions of deciding whether to replace or renovate the super heater of the power plant.
Abstract: Major depressive disorder (MDD) is one of the most common mental illnesses today. It is believed to be caused by a combination of several factors, including stress. Stress can be quantitatively evaluated using the State-Trait Anxiety Inventory (STAI), one of the best indices to evaluate anxiety. Although STAI scores are widely used in applications ranging from clinical diagnosis to basic research, the scores are calculated based on a self-reported questionnaire. An objective evaluation is required because the subject may intentionally change his/her answers if multiple tests are carried out. In this article, we present a modified index called the “multi-channel Laterality Index at Rest (mc-LIR)” by recording the brain activity from a wider area of the frontal lobe using multi-channel functional near-infrared spectroscopy (fNIRS). The presented index aims to measure multiple positions near the Fpz defined by the international 10-20 system positioning. Using 24 subjects, the dependencies on the number of measuring points used to calculate the mc-LIR and its correlation coefficients with the STAI scores are reported. Furthermore, a simple linear regression was performed to estimate the STAI scores from mc-LIR. The cross-validation error is also reported. The experimental results show that using multiple positions near the Fpz will improve the correlation coefficients and estimation than those using only two positions.
Abstract: Trackside induced airflow velocities, also known as
slipstream velocities, are an important criterion for the design of
high-speed trains. The maximum permitted values are given by the
Technical Specifications for Interoperability (TSI) and have to be
checked in the approval process. For train manufactures it is of great
interest to know in advance, how new train geometries would perform
in TSI tests. The Reynolds number in moving model experiments is
lower compared to full-scale. Especially the limited model length
leads to a thinner boundary layer at the rear end. The hypothesis is
that the boundary layer rolls up to characteristic flow structures in the
train wake, in which the maximum flow velocities can be observed.
The idea is to enlarge the boundary layer using roughness elements
at the train model head so that the ratio between the boundary
layer thickness and the car width at the rear end is comparable to a
full-scale train. This may lead to similar flow structures in the wake
and better prediction accuracy for TSI tests. In this case, the design
of the roughness elements is limited by the moving model rig. Small
rectangular roughness shapes are used to get a sufficient effect on the
boundary layer, while the elements are robust enough to withstand
the high accelerating and decelerating forces during the test runs. For
this investigation, High-Speed Particle Image Velocimetry (HS-PIV)
measurements on an ICE3 train model have been realized in the
moving model rig of the DLR in Göttingen, the so called tunnel
simulation facility Göttingen (TSG). The flow velocities within the
boundary layer are analysed in a plain parallel to the ground. The
height of the plane corresponds to a test position in the EN standard
(TSI). Three different shapes of roughness elements are tested. The
boundary layer thickness and displacement thickness as well as the
momentum thickness and the form factor are calculated along the
train model. Conditional sampling is used to analyse the size and
dynamics of the flow structures at the time of maximum velocity
in the train wake behind the train. As expected, larger roughness
elements increase the boundary layer thickness and lead to larger
flow velocities in the boundary layer and in the wake flow structures.
The boundary layer thickness, displacement thickness and momentum
thickness are increased by using larger roughness especially when
applied in the height close to the measuring plane. The roughness
elements also cause high fluctuations in the form factors of the
boundary layer. Behind the roughness elements, the form factors
rapidly are approaching toward constant values. This indicates that
the boundary layer, while growing slowly along the second half of
the train model, has reached a state of equilibrium.
Abstract: This work contributes a statistical model and simulation
framework yielding the best estimate possible for the potential
herbicide reduction when using the MoDiCoVi algorithm all the
while requiring a efficacy comparable to conventional spraying. In
June 2013 a maize field located in Denmark were seeded. The field
was divided into parcels which was assigned to one of two main
groups: 1) Control, consisting of subgroups of no spray and full dose
spraty; 2) MoDiCoVi algorithm subdivided into five different leaf
cover thresholds for spray activation. In addition approximately 25%
of the parcels were seeded with additional weeds perpendicular to
the maize rows. In total 299 parcels were randomly assigned with
the 28 different treatment combinations. In the statistical analysis,
bootstrapping was used for balancing the number of replicates. The
achieved potential herbicide savings was found to be 70% to 95%
depending on the initial weed coverage. However additional field
trials covering more seasons and locations are needed to verify
the generalisation of these results. There is a potential for further
herbicide savings as the time interval between the first and second
spraying session was not long enough for the weeds to turn yellow,
instead they only stagnated in growth.
Abstract: Nowadays, nanoparticles are being used in pharmacological studies for their exclusive properties such as small size, more surface area, biocompatibility and enhanced solubility. In view of this, the present study aimed to evaluate the antihyperglycemic potential of biologically synthesized silver nanoparticles (BSSNPs) and Gymnema sylvestre (GS) extract. The SEM and SEM analysis divulges that the BSSNPs were spherical in shape. EDAX spectrum exhibits peaks for the presence of silver, carbon, and oxygen atoms in the range of 1.0-3.1 keV. FT-IR reveals the binding properties of active bio-constituents responsible for capping and stabilizing BSSNPs. The results showed increased blood glucose, huge loss in body weight and downturn in plasma insulin. The GS extract (200 mg/kg, 400 mg/kg), BSSNPs (100 mg/kg, 200 mg/kg) and metformin 50 mg/kg were administered to the diabetic rats. BSSNPs at a dose level of 200 mg/kg (b.wt.p.o.) showed significant inhibition of (p
Abstract: This paper presents a kind of analog circuit based
temperature control system, which is mainly composed by threshold
control signal circuit, synchronization signal circuit and trigger
pulse circuit. Firstly, the temperature feedback signal function is
realized by temperature sensor TS503F3950E. Secondly, the main
control circuit forms the cycle controlled pulse signal to control
the thyristor switching model. Finally two reverse paralleled
thyristors regulate the output power by their switching state. In
the consequence, this is a modernized and energy-saving domestic
electric heating system.
Abstract: Due to the economic downturn and the deterioration of the living environment, the development of residential buildings as high energy consuming building is gradually changing from “extensive” to green building in China. So, the evaluation system of green building is continuously improved, but the current evaluation work has the following problems: (1) There are differences in the cost of the actual investment and the purchasing power of residents, also construction target of green residential building is single and lacks multi-objective performance development. (2) Green building evaluation lacks regional characteristics and cannot reflect the different regional residents demand. (3) In the process of determining the criteria weight, the experts’ judgment matrix is difficult to meet the requirement of consistency. Therefore, to solve those problems, questionnaires which are about the green residential building for Ningxia area are distributed, and the results of questionnaires can feedback the purchasing power of residents and the acceptance of the green building cost. Secondly, combined with the geographical features of Ningxia minority areas, the evaluation criteria system of green residential building is constructed. Finally, using the improved group AHP method and the grey clustering method, the criteria weight is determined, and a real case is evaluated, which is located in Xing Qing district, Ningxia. A conclusion can be obtained that the professional evaluation for this project and good social recognition is basically the same.
Abstract: This paper discusses the effects of sodium hypophosphite concentration, pH, and temperature on deposition rate. This paper also discusses the evaluation of coating strength, surface, and subsurface by varying the bath parameters, percentage of phosphate, plating temperature, and pH of the plating solution. Taguchi technique has been used for the analysis. In the experiment, nickel chloride which is a source of nickel when mixed with sodium hypophosphite has been used as the reducing agent and the source of phosphate and sodium hydroxide has been used to vary the pH of the coating bath. The coated samples are tested for impact energy by conducting impact test. Finally, the effects of coating bath parameters on the impact energy absorbed have been plotted, and analysis has been carried out. Further, percentage contribution of coating bath parameters using Design of Experiments approach (DOE) has been analysed. Finally, it can be concluded that the bath parameters of the Ni-P coating will certainly influence on the strength of the specimen.
Abstract: This paper describes the development of a model of an impaired human arm performing a reaching motion, which will be used to predict hand path trajectories for people with reduced arm joint mobility. Assuming that the arm was in contact with a surface during the entire movement, the contact conditions at the initial and final task locations were determined and used to generate the entire trajectory. The model was validated by comparing it to experimental data, which simulated an arm joint impairment by physically constraining the joint motion with a brace. Future research will include using the model in the development of physical training protocols that avoid early recruitment of “healthy” Degrees-Of-Freedom (DOF) for reaching motions, thus facilitating an Active Range-Of-Motion Recovery (AROM) for a particular impaired joint.
Abstract: This study deals with wage inequality in organization
and shows the relationship between ICT and wage in organization.
To do so, we incorporate ICT’s factors in organization into our
model. ICT’s factors are efficiencies of Enterprise Resource
Planning (ERP), Computer Assisted Design/Computer Assisted
Manufacturing (CAD/CAM), and NETWORK. The improvement of
ICT’s factors decrease the learning cost to solve problem pertaining
to the hierarchy in organization. The improvement of NETWORK
increases the wage inequality within workers and decreases within
managers and entrepreneurs. The improvements of CAD/CAM and
ERP increases the wage inequality within all agent, and partially
increase it between the agents in hierarchy.
Abstract: In this paper, the BP neural network model is established to predict the carbon trading price and carbon trading volume in Shanghai City. First of all, we find the data of carbon trading price and carbon trading volume in Shanghai City from September 30, 2015 to December 23, 2016. The carbon trading price and trading volume data were processed to get the average value of each 5, 10, 20, 30, and 60 carbon trading price and trading volume. Then, these data are used as input of BP neural network model. Finally, after the training of BP neural network, the prediction values of Shanghai carbon trading price and trading volume are obtained, and the model is tested.
Abstract: Equivalent circuit models (ECMs) are widely used in
battery management systems in electric vehicles and other battery
energy storage systems. The battery dynamics and the model
parameters vary under different working conditions, such as different
temperature and state of charge (SOC) levels, and therefore online
parameter identification can improve the modelling accuracy. This
paper presents a way of online ECM parameter identification using a
continuous time (CT) estimation method. The CT estimation method
has several advantages over discrete time (DT) estimation methods
for ECM parameter identification due to the widely separated battery
dynamic modes and fast sampling. The presented method can be used
for online SOC estimation. Test data are collected using a lithium ion
cell, and the experimental results show that the presented CT method
achieves better modelling accuracy compared with the conventional
DT recursive least square method. The effectiveness of the presented
method for online SOC estimation is also verified on test data.
Abstract: One of the main characteristics of Heavy Water Moderated Reactors is their high production of plutonium. This article demonstrates the possibility of reduction of plutonium and other actinides in Heavy Water Research Reactor. Among the many ways for reducing plutonium production in a heavy water reactor, in this research, changing the fuel from natural Uranium fuel to Thorium-Uranium mixed fuel was focused. The main fissile nucleus in Thorium-Uranium fuels is U-233 which would be produced after neutron absorption by Th-232, so the Thorium-Uranium fuels have some known advantages compared to the Uranium fuels. Due to this fact, four Thorium-Uranium fuels with different compositions ratios were chosen in our simulations; a) 10% UO2-90% THO2 (enriched= 20%); b) 15% UO2-85% THO2 (enriched= 10%); c) 30% UO2-70% THO2 (enriched= 5%); d) 35% UO2-65% THO2 (enriched= 3.7%). The natural Uranium Oxide (UO2) is considered as the reference fuel, in other words all of the calculated data are compared with the related data from Uranium fuel. Neutronic parameters were calculated and used as the comparison parameters. All calculations were performed by Monte Carol (MCNPX2.6) steady state reaction rate calculation linked to a deterministic depletion calculation (CINDER90). The obtained computational data showed that Thorium-Uranium fuels with four different fissile compositions ratios can satisfy the safety and operating requirements for Heavy Water Research Reactor. Furthermore, Thorium-Uranium fuels have a very good proliferation resistance and consume less fissile material than uranium fuels at the same reactor operation time. Using mixed Thorium-Uranium fuels reduced the long-lived α emitter, high radiotoxic wastes and the radio toxicity level of spent fuel.
Abstract: In this article, we present the principle and suitable methodology for the design of a medical ontology that highlights the radiological and dosimetric knowledge, applied in diagnostic radiology and radiation-therapy. Our ontology, which we named «Onto.Rap», is the subject of radiation protection in medical and radiology centers by providing a standardized regulatory oversight. Thanks to its added values of knowledge-sharing, reuse and the ease of maintenance, this ontology tends to solve many problems. Of which we name the confusion between radiological procedures a practitioner might face while performing a patient radiological exam. Adding to it, the difficulties they might have in interpreting applicable patient radioprotection standards. Here, the ontology, thanks to its concepts simplification and expressiveness capabilities, can ensure an efficient classification of radiological procedures. It also provides an explicit representation of the relations between the different components of the studied concept. In fact, an ontology based-radioprotection expert system, when used in radiological center, could implement systematic radioprotection best practices during patient exam and a regulatory compliance service auditing afterwards.
Abstract: This paper describes in details a commercial green building that has been designed and constructed in Marsa Matrouh, Egypt. The balance between homebuilding and the sustainable environment has been taken into consideration in the design and construction of this building. The building consists of one floor with 3 m height and 2810 m2 area while the envelope area is 1400 m2. The building construction fulfills the natural ventilation requirements. The glass curtain walls are about 50% of the building and the windows area is 300 m2. 6 mm greenish gray tinted temper glass as outer board lite, 6 mm safety glass as inner board lite and 16 mm thick dehydrated air spaces are used in the building. Visible light with 50% transmission, 0.26 solar factor, 0.67 shading coefficient and 1.3 W/m2.K thermal insulation U-value are implemented to realize the performance requirements. Optimum electrical distribution for lighting system, air conditions and other electrical loads has been carried out. Power and quantity of each type of the lighting system lamps and the energy consumption of the lighting system are investigated. The design of the air conditions system is based on summer and winter outdoor conditions. Ventilated, air conditioned spaces and fresh air rates are determined. Variable Refrigerant Flow (VRF) is the air conditioning system used in this building. The VRF outdoor units are located on the roof of the building and connected to indoor units through refrigerant piping. Indoor units are distributed in all building zones through ducts and air outlets to ensure efficient air distribution. The green building energy consumption is evaluated monthly all over one year and compared with the consumed energy in the non-green conditions using the Hourly Analysis Program (HAP) model. The comparison results show that the total energy consumed per year in the green building is about 1,103,221 kWh while the non-green energy consumption is about 1,692,057 kWh. In other words, the green building total annual energy cost is reduced from 136,581 $ to 89,051 $. This means that, the energy saving and consequently the money-saving of this green construction is about 35%. In addition, 13 points are awarded by applying one of the most popular worldwide green energy certification programs (Leadership in Energy and Environmental Design “LEED”) as a rating system for the green construction. It is concluded that this green building ensures sustainability, saves energy and offers an optimum energy performance with minimum cost.
Abstract: Europe is one of the most popular tourist destinations in the world, in which tourism occupies a significant place among the most relevant economic activities, and this applies to the Republic of Croatia as well. Based on this study, the authors intended to encourage and support the creation of an effective tourism policy in Croatia that would be based on the profiling of certain target groups. Another objective was to compare the results obtained from the customer analysis with the market analysis of the tourism industry in Croatia. The objective is to adapt the current tourist offer according to the identified needs and expectations of a particular tourist group in order to increase the attractiveness of Croatia as a tourist destination and motivate greater attendance of the targeted tourist groups. The current research was oriented towards the Russian market as the target group. Therefore, the authors wanted to encourage a discussion on how to attract more Russian guests. Consequently, the intention of the research was a detailed analysis of Russian tourists, in order to gain a better understanding of their travelling motives and tendencies. Furthermore, attention was paid to the expectations of Russian customers and to compare them with the Croatian tourist offer, and to determine whether there is a possibility for an overlap. The method used to obtain the information required was a survey conducted among Russian citizens about their travelling habits. The research was carried out on the basis of 166 participants of different age, gender, profession and income group. The sampling and distribution of the survey took place between May and July 2016. The results provided from the research indicate that Croatian tourism has certain unrealized potential considering the popularization of Croatia as a tourist destination, and there is a capacity for increasing the revenues within the group of Russian tourists. Such a conclusion is based on the fact that the Croatian tourist offer and the preferences of the Russian guests are compatible, i.e. they overlap in many aspects. The results demonstrate that beautiful nature, cultural and historical heritage as well as the sun and sea, play a leading role in attracting more Russian tourists. It is precisely these elements that form the three pillars of the Croatian tourist offer. On the other hand, the profiling revealed that the most desirable destinations for the Russian guests are Italy and Spain, both of which provide the same main tourist attractions as Croatia. Therefore, the focus of the strategic ideas given in the paper shifted to other tourism segments, such as type of accommodation, sales channels, travel motives, additional offer and seasonality etc., in order to gain advantage in the Russian market, the Mediterranean region and tourism in general. The purpose of the research is to serve as a foundation for analysing the attractiveness of the other tourist destinations in the Russian market, as well as to be a general basis for a more detailed profiling of the various specific target groups of the Russian and other tourist groups.
Abstract: Many organizations are faced with the challenge of how to analyze and build Machine Learning models using their sensitive telemetry data. In this paper, we discuss how users can leverage the power of R without having to move their big data around as well as a cloud based solution for organizations willing to host their data in the cloud. By using ScaleR technology to benefit from parallelization and remote computing or R Services on premise or in the cloud, users can leverage the power of R at scale without having to move their data around.
Abstract: Since additive manufacturing technologies constantly advance, the use of this technology in mold making seems reasonable. Many manufacturers of additive manufacturing machines, however, do not offer any suggestions on how to parameterize the machine to achieve optimal results for mold making. The purpose of this research is to determine the interdependencies of different materials and parameters within the PolyJet process by using design of experiments (DoE), to additively manufacture molds, e.g. for thermoforming and injection molding applications. Therefore, the general requirements of thermoforming molds, such as heat resistance, surface quality and hardness, have been identified. Then, different materials and parameters of the PolyJet process, such as the orientation of the printed part, the layer thickness, the printing mode (matte or glossy), the distance between printed parts and the scaling of parts, have been examined. The multifactorial analysis covers the following properties of the printed samples: Tensile strength, tensile modulus, bending strength, elongation at break, surface quality, heat deflection temperature and surface hardness. The key objective of this research is that by joining the results from the DoE with the requirements of the mold making, optimal and tailored molds can be additively manufactured with the PolyJet process. These additively manufactured molds can then be used in prototyping processes, in process testing and in small to medium batch production.