Abstract: The electric power supplied by a photovoltaic power
generation systems depends on the solar irradiation and temperature.
The PV system can supply the maximum power to the load at a
particular operating point which is generally called as maximum
power point (MPP), at which the entire PV system operates with
maximum efficiency and produces its maximum power. Hence, a
Maximum power point tracking (MPPT) methods are used to
maximize the PV array output power by tracking continuously the
maximum power point. The proposed MPPT controller is designed
for 10kW solar PV system installed at Cape Institute of Technology.
This paper presents the fuzzy logic based MPPT algorithm. However,
instead of one type of membership function, different structures of
fuzzy membership functions are used in the FLC design. The
proposed controller is combined with the system and the results are
obtained for each membership functions in Matlab/Simulink
environment. Simulation results are decided that which membership
function is more suitable for this system.
Abstract: In this paper, Least Mean Square (LMS) adaptive
noise reduction algorithm is proposed to enhance the speech signal
from the noisy speech. In this, the speech signal is enhanced by
varying the step size as the function of the input signal. Objective and
subjective measures are made under various noises for the proposed
and existing algorithms. From the experimental results, it is seen that
the proposed LMS adaptive noise reduction algorithm reduces Mean
square Error (MSE) and Log Spectral Distance (LSD) as compared to
that of the earlier methods under various noise conditions with
different input SNR levels. In addition, the proposed algorithm
increases the Peak Signal to Noise Ratio (PSNR) and Segmental SNR
improvement (ΔSNRseg) values; improves the Mean Opinion Score
(MOS) as compared to that of the various existing LMS adaptive
noise reduction algorithms. From these experimental results, it is
observed that the proposed LMS adaptive noise reduction algorithm
reduces the speech distortion and residual noise as compared to that
of the existing methods.
Abstract: Underwater acoustic network is one of the rapidly
growing areas of research and finds different applications for
monitoring and collecting various data for environmental studies. The
communication among dynamic nodes and high error probability in
an acoustic medium forced to maximize energy consumption in
Underwater Sensor Networks (USN) than in traditional sensor
networks. Developing energy-efficient routing protocol is the
fundamental and a curb challenge because all the sensor nodes are
powered by batteries, and they cannot be easily replaced in UWSNs.
This paper surveys the various recent routing techniques that mainly
focus on energy efficiency.
Abstract: The fuzzy composition of objects depicted in images
acquired through MR imaging or the use of bio-scanners has often
been a point of controversy for field experts attempting to effectively
delineate between the visualized objects. Modern approaches in
medical image segmentation tend to consider fuzziness as a
characteristic and inherent feature of the depicted object, instead of
an undesirable trait. In this paper, a novel technique for efficient
image retrieval in the context of images in which segmented objects
are either crisp or fuzzily bounded is presented. Moreover, the
proposed method is applied in the case of multiple, even conflicting,
segmentations from field experts. Experimental results demonstrate
the efficiency of the suggested method in retrieving similar objects
from the aforementioned categories while taking into account the
fuzzy nature of the depicted data.
Abstract: A cleaner production project was implemented in a
bakery. The project is based on the substitution of the best available
technique for an obsolete leaven production technology. The new
technology enables production of durable, high-quality leavens.
Moreover, 25% of flour as the original raw material can be replaced
by pastry from the previous day production which has not been sold.
That pastry was previously disposed in a waste incineration plant.
Besides the environmental benefits resulting from less waste, lower
consumption of energy, reduction of sewage waters quantity and
floury dustiness there are also significant economic benefits. Payback
period of investment was calculated with help of static method of
financial analysis about 2.6 years, using dynamic method 3.5 years
and an internal rate of return more than 29%. The supposed annual
average profit after taxationin the second year of operation was
incompliance with the real profit.
Abstract: E-business technologies, whereby business
transactions are conducted remotely using the Internet, present
unique opportunities and challenges for business. E-business
technologies are applicable to a wide range of organizations and
small and medium-sized enterprises (SMEs) are no exception. There
is an established body of literature about e-business, looking at
definitions, concepts, benefits and challenges. In general, however,
the research focus has been on larger organizations, not SMEs. In an
attempt to redress the balance of research, this paper looks at ebusiness
technologies specifically from a small business perspective.
It seeks to identify the possible barriers that SMEs might face when
considering adoption of the e-business concept and practice as part of
their business process change initiatives and implementation. To
facilitate analysis of these barriers a conceptual framework has been
developed which outlines the key conceptual and practical challenges
of e-business implementation in SMEs. This is developed following a
literature survey comprised of three categories: characteristics of
SMEs, issues of IS/IT use in SMEs and general e-business adoption
and implementation issues. The framework is then empirically
assessed against 7 SMEs who have yet to implement e-business or
whose e-business efforts have been unsatisfactory. Conclusions from
the case studies can be used to verify the framework, and set
parameters for further larger scale empirical investigation.
Abstract: Enterprise Architecture (EA) is a strategy that is
employed by enterprises in order to align their business and
Information Technology (IT). EA is managed, developed, and
maintained through Enterprise Architecture Implementation
Methodology (EAIM). Effectiveness of EA implementation is the
degree in which EA helps to achieve the collective goals of the
organization. This paper analyzes the results of a survey that aims to
explore the factors that affect the effectiveness of EAIM and
specifically the relationship between factors and effectiveness of the
output and functionality of EA project. The exploratory factor
analysis highlights a specific set of five factors: alignment,
adaptiveness, support, binding, and innovation. The regression
analysis shows that there is a statistically significant and positive
relationship between each of the five factors and the effectiveness of
EAIM. Consistent with theory and practice, the most prominent
factor for developing an effective EAIM is innovation. The findings
contribute to the measuring the effectiveness of EA implementation
project by providing an indication of the measurement
implementation approaches which is used by the Enterprise
Architects, and developing an effective EAIM.
Abstract: In the UK, flooding is responsible for significant
losses to the economy due to the impact on businesses, the vast
majority of which are Small and Medium Enterprises (SMEs).
Businesses of this nature tend to lack formal plans to aid their
response to and recovery from disruptive events such as flooding.
This paper reports on work on how an agent-based model (ABM) is
being developed based on interview data gathered from SMEs at-risk
of flooding and/or have direct experience of flooding. The ABM will
enable simulations to be performed allowing investigations of
different response strategies which SMEs may employ to lessen the
impact of flooding, thus strengthening their resilience.
Abstract: The dramatic rise in the use of Social Media (SM)
platforms such as Facebook and Twitter provide access to an
unprecedented amount of user data. Users may post reviews on
products and services they bought, write about their interests, share
ideas or give their opinions and views on political issues. There is a
growing interest in the analysis of SM data from organisations for
detecting new trends, obtaining user opinions on their products and
services or finding out about their online reputations. A recent
research trend in SM analysis is making predictions based on
sentiment analysis of SM. Often indicators of historic SM data are
represented as time series and correlated with a variety of real world
phenomena like the outcome of elections, the development of
financial indicators, box office revenue and disease outbreaks. This
paper examines the current state of research in the area of SM mining
and predictive analysis and gives an overview of the analysis
methods using opinion mining and machine learning techniques.
Abstract: As enterprise computing becomes more and more
complex, the costs and technical challenges of IT system maintenance
and support are increasing rapidly. One popular approach to managing
IT system maintenance is to prepare and use a FAQ (Frequently Asked
Questions) system to manage and reuse systems knowledge. Such a
FAQ system can help reduce the resolution time for each service
incident ticket. However, there is a major problem where over time the
knowledge in such FAQs tends to become outdated. Much of the
knowledge captured in the FAQ requires periodic updates in response
to new insights or new trends in the problems addressed in order to
maintain its usefulness for problem resolution. These updates require a
systematic approach to define the exact portion of the FAQ and its
content. Therefore, we are working on a novel method to
hierarchically structure the FAQ and automate the updates of its
structure and content. We use structured information and the
unstructured text information with the timelines of the information in
the service incident tickets. We cluster the tickets by structured
category information, by keywords, and by keyword modifiers for the
unstructured text information. We also calculate an urgency score
based on trends, resolution times, and priorities. We carefully studied
the tickets of one of our projects over a 2.5-year time period. After the
first 6 months we started to create FAQs and confirmed they improved
the resolution times. We continued observing over the next 2 years to
assess the ongoing effectiveness of our method for the automatic FAQ
updates. We improved the ratio of tickets covered by the FAQ from
32.3% to 68.9% during this time. Also, the average time reduction of
ticket resolution was between 31.6% and 43.9%. Subjective analysis
showed more than 75% reported that the FAQ system was useful in
reducing ticket resolution times.
Abstract: In oases, the surface water resources are becoming
increasingly scarce and groundwater resources, which generally have
a poor quality due to the high levels of salinity, are often
overexploited. Water saving have therefore become imperative for
better oases sustainability. If drip irrigation is currently recommended
in Morocco for saving water and valuing, its use in the sub-desert
areas does not keep water safe from high evaporation rates. An
alternative to this system would be the use of subsurface drip
irrigation. This technique is defined as an application of water under
the soil surface through drippers, which deliver water at rates
generally similar to surface drip irrigation. As subsurface drip
irrigation is a recently introduced in Morocco, a better understanding
of the infiltration process around a buried source, in local conditions,
and its impact on plant growth is necessarily required. This study
aims to contribute to improving the water use efficiency by testing
the performance of subsurface irrigation system, especially in areas
where water is a limited source. The objectives of this research are
performance evaluation in arid conditions of the subsurface drip
irrigation system for young date palms compared to the surface drip.
In this context, an experimental test is installed at a farmer’s field in
the area of Erfoud (Errachidia Province, southeastern Morocco),
using the subsurface drip irrigation system in comparison with the
classic drip system for young date palms. Flow measurement to
calculate the uniformity of the application of water was done through
two methods: a flow measurement of drippers above the surface and
another one underground. The latter method has also helped us to
estimate losses through evaporation for both irrigation techniques. In
order to compare the effect of two irrigation modes, plants were
identified for each type of irrigation to monitor certain agronomic
parameters (cumulative numbers of palms and roots development).
Experimentation referred to a distribution uniformity of about 88%;
considered acceptable for subsurface drip irrigation while it is around
80% for the surface drip irrigation. The results also show an increase
in root development and in the number of palm, as well as a
substantial water savings due to lower evaporation losses compared
to the classic drip irrigation.
The results of this study showed that subsurface drip irrigation is
an efficient technique, which allows sustainable irrigation in arid
areas.
Abstract: Oases are complex and fragile agro-ecosystems. They
have always existed in environments characterized by an arid climate,
scarcity of rainfall, high temperatures and high evaporation. These
palms have grown up despite the severity of the physical
characteristics thanks to the water's existence and irrigation practice.
The oases are generally spread along non-perennial rivers (wadis),
shallow water table or deep artesian groundwater. However, the
sustainability of oasis system is threatened by water scarcity and
declining of water table levels particularly in arid areas. Located in
the southern east area of Morocco, Tafilalet plain encompasses one of
the largest palm groves in the kingdom. In recent years, this area has
become increasingly threatened by water shortage and has seen a
sharp deterioration under the effect of several combined
anthropogenic and climatic factors. The Bayoud disease, successive
years of drought, Hassan Addakhil dam construction etc are all
factors that have affected both water and phoenicicole heritage of the
area. The objective of this study is to understand the interaction
between qualitative and quantitative degradation of groundwater
resources, and the palm grove dynamics, while reviewing the
assumption that groundwater resources contribute in a direct way to
the conservation of this oasis agroecosystem. A historical analysis
tracing both the oasis dynamics and the groundwater evolution has
been established. Data were collected from satellite images, surveys
with different actors (farmers, Regional Office for Agricultural
Development, Basin agency...). They were complemented by a
synthesis of numerous technical reports in the area. The results
showed that within 40 years, the thickness of the groundwater table
has dropped in 50 %. Along with this, there has been a downsizing of
date palm by 50 %. Areas with higher groundwater level were the
least affected by the downsizing. So we can say that the shallow
groundwater contribute significantly and directly to the water supply
of date palm through its root system, and largely ensures the oasis
ecosystem sustainability.
Abstract: Wireless sensor network (WSN) is a network of many interconnected networked systems, they equipped with energy resources and they are used to detect other physical characteristics. On WSN, there are many researches are performed in past decades. WSN applicable in many security systems govern by military and in many civilian related applications. Thus, the security of WSN gets attention of researchers and gives an opportunity for many future aspects. Still, there are many other issues are related to deployment and overall coverage, scalability, size, energy efficiency, quality of service (QoS), computational power and many more. In this paper we discus about various applications and security related issue and requirements of WSN.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: Two Lithium Disilicate (LD) glass ceramics based on
SiO2-Li2O-K2O-Al2O3 system were prepared through a glass melting
method. The glass rods were then fabricated into dental crowns via a
hot pressing at 900˚C and 850˚C in order to study the effect of the
pressing temperatures on the phase formation and microstructure of
the glasses. Different samples of as cast glass and heat treated
samples (600˚C and 700˚C) were used to press for investigating the
effect of an initial microstructure on the hot pressing technique. Xray
diffraction (XRD) and scanning electron microscopy (SEM) were
performed to determine the phase formation and microstructure of the
samples, respectively. XRD results show that the main crystalline
structure was Li2Si2O5 by having Li3PO4, Li0.6Al0.6Si2O6, Li2SiO3,
Ca5 (PO4)3F and SiO2 as minor phases. Glass compositions with
different heat treatment temperatures exhibited a difference phase
formations but have less effect during pressing. SEM micrographs
showed the microstructure of Li2Si2O5 as lath-like shape in all
glasses. With increasing the initial heat treatment temperature, the
longer the lath-like crystals of lithium disilicate were increased
especially when using glass heat treatment at 700˚C followed by
pressing at 900˚C. This could be suggested that LD1 heat treatment at
700˚C which pressing at 900˚C presented the best formation by the
hot pressing and compiled microstructure.
Abstract: Augmented Reality is a technology that involves the
overlay of virtual content, which is context or environment sensitive,
on images of the physical world in real time. This paper presents the
development of a catalog system that facilitates and allows the
creation, publishing, management and exploitation of augmented
multimedia contents and Augmented Reality applications, creating an
own space for anyone that wants to provide information to real
objects in order to edit and share it then online with others. These
spaces would be built for different domains without the initial need of
expert users. Its operation focuses on the context of Web 2.0 or
Social Web, with its various applications, developing contents to
enrich the real context in which human beings act permitting the
evolution of catalog’s contents in an emerging way.
Abstract: Sports games conducted as a group are a form of
therapeutic exercise for aged people with decreased strength and for
people suffering from permanent damage of stroke and other
conditions. However, it is difficult for patients with different athletic
abilities to play a game on an equal footing. This study specifically
examines a computer video game designed for therapeutic exercise,
and a game system with support given depending on athletic ability.
Thereby, anyone playing the game can participate equally. This
video-game, to be specific, is a popular variant of balloon volleyball,
in which players hit a balloon by hand before it falls to the floor. In this
game system, each player plays the game watching a monitor on which
the system displays tailor-made video-game images adjusted to the
person’s athletic ability, providing players with player-adaptive assist
support. We have developed a multiplayer game system with an image
generation technique for the tailor-made video-game and conducted
tests to evaluate it.
Abstract: This paper describes a logical method to enhance
security on the grid computing to restrict the misuse of the grid
resources. This method is an economic and efficient one to avoid the
usage of the special devices. The security issues, techniques and
solutions needed to provide a secure grid computing environment are
described. A well defined process for security management among
the resource accesses and key holding algorithm is also proposed. In
this method, the identity management, access control and
authorization and authentication are effectively handled.
Abstract: In today’s highly competitive, dynamic and
technology driven business circumstances, marketers are under
steady pressure to deliver the best. Organizations are continuously
improving and upgrading themselves to meet customer expectations
and demands. Technology has not only changed the way in which
business is done in modern times but has also transformed the way to
reach out to target audience. Marketers have identified most recent
media options to communicate and convince potential customers.
Numerous scholars have studied the research domain of advertising
and have tried to recognize different measures of advertisement
effectiveness in context of various media. The objective of this paper
is to critically review accessible literature on advertisement
effectiveness in context of varied advertising media, recognize major
gaps in the literature and identify future research prospects on the
basis of critical analysis of literature.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.