Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: In an attempt to investigate the performance of single
basin solar still for climate conditions of Ludhiana a single basin
solar still was designed, fabricated and tested. The energy balance
equations for various parts of the still are solved by Gauss-Seidel
iteration method. Computer model was made and experimentally
validated. The validated computer model was used to estimate the
annual distillation yield and performance ratio of the still for
Ludhiana. The Theoretical and experimental distillation yield were
4318.79 ml and 3850 ml respectively for the typical day. The
predicted distillation yield was 12.5% higher than the experimental
yield. The annual distillation yield per square metre aperture area and
annual performance ratio for single basin solar still is 1095 litres and
0.43 respectively. The payback period for micro-stepped solar still is
2.5 years.
Abstract: The present study aims to investigate the performance
of Moringa oleifera seed extract as natural coagulant in clarification
of secondary wastewater treatment plant (MWWTP) located in East
of Algiers, Algeria. Coagulation flocculation performance of
Moringa oleifera was evaluated through supernatant residual
turbidity after jar test trials. Various influence parameters namely
Moringa oleifera dosage and pH have been considered. Tests on
Reghaia wastewater, having 129 NTU of initial turbidity, showed a
removal of 69.45% of residual turbidity with only 1.5 mg/l of
Moringa oleifera. This sufficient removal capability encourages the
use of this bioflocculant for treatment of turbid waters. Indeed,
Moringa oleifera which is a natural resource available locally (South
of Algeria) coupled to the non-toxicity, biocompatibility and
biodegradability, may be a very interesting alternative to the
conventional coagulants used so far.
Abstract: Electrostatic interaction energy (ΔEEDL) is a part of the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, which, together with van der Waals (ΔEVDW) and acid base (ΔEAB) interaction energies, has been extensively used to investigate the initial adhesion of bacteria to surfaces. Electrostatic or electrical double layer interaction energy is considerably affected by surface potential; however it cannot be determined experimentally and is usually replaced by zeta (ζ) potential via electrophoretic mobility. This paper focusses on the effect of ionic concentration as a function of pH and the effect of mineral grain size on ζ potential. It was found that both ionic strength and mineral grain size play a major role in determining the value of ζ potential for the adhesion of P. putida to hematite and quartz surfaces. Higher ζ potential values lead to higher electrostatic interaction energies and eventually to higher total XDLVO interaction energy resulting in bacterial repulsion.
Abstract: Passive control methods can be utilized to build
earthquake resistant structures, and also to strengthen the vulnerable
ones. In this paper, we studied the effect of this system in increasing
the ductility and energy dissipation and also modeled the behavior of
this type of eccentric bracing, and compared the hysteresis diagram
of the modeled samples with the laboratory samples. We studied
several samples of frames with vertical shear-links in order to assess
the behavior of this type of eccentric bracing. Each of these samples
was modeled in finite element software ANSYS 9.0, and was
analyzed under the static cyclic loading. It was found that vertical
shear-links have a more stable hysteresis loops. Another analysis
showed that using honeycomb beams as the horizontal beam along
with steel reinforcement has no negative effect on the hysteresis
behavior of the sample.
Abstract: This paper proposes that in the course of evolution
pitch structure became a human specific tool of communication the
function of which is to induce emotional states such as uncertainty
and cohesion. By the means of eliciting these emotions during
collective music performance people are able to unconsciously give
cues concerning social acceptance. This is probably one of the
reasons why in all cultures people collectively perform tonal music. It
is also suggested that tonal pitch structure had been invented socially
before it became an evolutionary innovation of hominines. It means
that a predisposition to tonally organize pitches evolved by the means
of ‘Baldwin effect’ – a process in which natural selection transforms
the learned response of an organism into the instinctive response. In
the proposed, hypothetical evolutionary scenario of the emergence of
tonal pitch structure social forces such as a need for closer
cooperation play the crucial role.
Abstract: This paper introduces a method to optimal design of a
hybrid Wind/Photovoltaic/Fuel cell generation system for a typical
domestic load that is not located near the electricity grid. In this
configuration the combination of a battery, an electrolyser, and a
hydrogen storage tank are used as the energy storage system. The aim
of this design is minimization of overall cost of generation scheme
over 20 years of operation. The Matlab/Simulink is applied for
choosing the appropriate structure and the optimization of system
sizing. A teaching learning based optimization is used to optimize the
cost function. An overall power management strategy is designed for
the proposed system to manage power flows among the different
energy sources and the storage unit in the system. The results have
been analyzed in terms of technical and economic. The simulation
results indicate that the proposed hybrid system would be a feasible
solution for stand-alone applications at remote locations.
Abstract: Investigating the dynamic responses of high rise
structures under the effect of siesmic ground motion is extremely
important for the proper analysis and design of multitoried structures.
Since the presence of infilled walls strongly influences the behaviour
of frame systems in multistoried buildings, there is an increased need
for developing guidelines for the analysis and design of infilled
frames under the effect of dynamic loads for safe and proper design
of buildings. In this manuscript, we evaluate the natural frequencies
and natural periods of single bay single storey frames considering the
effect of infill walls by using the Eigen value analysis and validating
with SAP 2000 (free vibration analysis). Various parameters obtained
from the diagonal strut model followed for the free vibration analysis
is then compared with the Finite Element model, where infill is
modeled as shell elements (four noded). We also evaluated the effect
of various parameters on the natural periods of vibration obtained by
free vibration analysis in SAP 2000 comparing them with those
obtained by the empirical expressions presented in I.S. 1893(Part I)-
2002.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: In the present paper the design of plate heat exchangers
is formulated as an optimization problem considering two
mathematical modelling. The number of plates is the objective
function to be minimized, considering implicitly some parameters
configuration. Screening is the optimization method used to solve the
problem. Thermal and hydraulic constraints are verified, not viable
solutions are discarded and the method searches for the convergence to
the optimum, case it exists. A case study is presented to test the
applicability of the developed algorithm. Results show coherency with
the literature.
Abstract: The access to relevant information that is adapted to
user’s needs, preferences and environment is a challenge in many
applications running. That causes an appearance of context-aware
systems. To facilitate the development of this class of applications, it
is necessary that these applications share a common context
metamodel. In this article, we will present our context metamodel
that is defined using the OMG Meta Object facility (MOF).This
metamodel is based on the analysis and synthesis of context concepts
proposed in literature.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: Electrohydraulic servo system have been used in
industry in a wide number of applications. Its dynamics are highly
nonlinear and also have large extent of model uncertainties and
external disturbances. In this paper, a robust back-stepping control
(RBSC) scheme is proposed to overcome the problem of disturbances
and system uncertainties effectively and to improve the tracking
performance of EHS systems. In order to implement the proposed
control scheme, the system uncertainties in EHS systems are
considered as total leakage coefficient and effective oil volume. In
addition, in order to obtain the virtual controls for stabilizing system,
the update rule for the system uncertainty term is induced by
the Lyapunov control function (LCF). To verify the performance and
robustness of the proposed control system, computer simulation of
the proposed control system using Matlab/Simulink Software
is executed. From the computer simulation, it was found that the
RBSC system produces the desired tracking performance and has
robustness to the disturbances and system uncertainties of EHS
systems.
Abstract: Land reallocation is one of the most important steps in
land consolidation projects. Many different models were proposed for
land reallocation in the literature such as Fuzzy Logic, block priority
based land reallocation and Spatial Decision Support Systems. A
model including four parts is considered for automatic block
reallocation with genetic algorithm method in land consolidation
projects. These stages are preparing data tables for a project land,
determining conditions and constraints of land reallocation, designing
command steps and logical flow chart of reallocation algorithm and
finally writing program codes of Genetic Algorithm respectively. In
this study, we designed the first three steps of the considered model
comprising four steps.
Abstract: This research paper presents the current practices of
teacher professional development, perceived as beneficial by teachers
themselves, in a private secondary school in Brunei Darussalam. This
is part of the findings of a larger qualitative study on teacher
empowerment, using ethnographic methods for data collection, i.e.
participant observation, interviews and document analysis. The field
work was carried out over a period of six months in 2013. An
analysis of the field data revealed multiple pathways of teacher
professional development existing in the school. The results indicate
that school leaders, the teacher community in the school, students,
and the teachers themselves were the agents in a school that
facilitated teacher empowerment. Besides contributing to the
knowledge base on teacher professional development, the results of
this study provide directions for educational policy makers in their
efforts to enhance professional development in secondary schools of
similar characteristics. For school leaders and the teacher community,
these findings offer guidelines for maximizing the opportunities for
these professional development practices, by strengthening
collegiality and by using the existing structures optimally for the
benefit of all concerned.
Abstract: In recent years, the use of the aluminum based alloys
in the industry and technology are increasing. Alloying elements in
aluminum have further been improving the strength and stiffness
properties that provide superior compared to other metals. In this
study, investigation of physical properties (microstructure,
microhardness, tensile strength, electrical conductivity and thermal
properties) in the Al-12.6wt.%Si-%2wt.Ni ternary alloy were
investigated. Al-Si-Ni alloy was prepared in vacuum atmosphere. The
samples were directionally solidified upwards with different growth
rate V (8.3−165.45 μm/s) at constant temperature gradient G (7.73
K/mm). The flake spacings (λ), microhardness (HV), ultimate tensile
strength (σ), electrical resistivity (ρ) and thermal properties (H, Cp,
Tm) of the samples were measured. Influence of the growth rate and
spacings on microhardness, ultimate tensile strength and electrical
resistivity were investigated and relationships between them were
obtained. According to results, λ values decrease with increasing V,
but HV, σ and ρ values increase with increasing V. Variations of
electrical resistivity (ρ) of solidified samples were also measured.
The enthalpy of fusion (H) and specific heat (Cp) for the alloy was
also determined by differential scanning calorimeter (DSC) from
heating trace during the transformation from liquid to solid. The
results in this work were compared with the previous similar
experimental results.