Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: Purpose of this work is the development of an
automatic classification system which could be useful for radiologists
in the investigation of breast cancer. The software has been designed
in the framework of the MAGIC-5 collaboration.
In the automatic classification system the suspicious regions with
high probability to include a lesion are extracted from the image as
regions of interest (ROIs). Each ROI is characterized by some
features based on morphological lesion differences.
Some classifiers as a Feed Forward Neural Network, a K-Nearest
Neighbours and a Support Vector Machine are used to distinguish the
pathological records from the healthy ones.
The results obtained in terms of sensitivity (percentage of
pathological ROIs correctly classified) and specificity (percentage of
non-pathological ROIs correctly classified) will be presented through
the Receive Operating Characteristic curve (ROC). In particular the
best performances are 88% ± 1 of area under ROC curve obtained
with the Feed Forward Neural Network.
Abstract: This work was conducted to improve the level of
resistant starch (RS) in a rice noodle using unripe banana flour and to
investigate the effect of substitution of unripe banana flour for rice
flour on the physical properties of rice noodle. In order to prepare
rice noodles, the unripe banana flour were replaced the rice flour
with different degrees of substitutions including 0, 20, 40, 60, 80, and
100%. The results indicated that substitution of unripe banana flour
was significantly affected the viscosity properties of noodle flour,
color, cooking loss, RS and total starch content of noodle. It was
found that the noodle prepared from 100% unripe banana indicated
the greatest changes on the viscosity properties and color profiles. It
also showed the highest values of cooking loss (2.53%), tensile
strength (129.03%), and RS content (13.15%).
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: The study investigated the educational implications
that can be derived from the work of a variety of celebrated figures
such as Piaget, Vygotsky, and Bruner that will be helpful in the field
of language learning. However, the writer believed these views were
previously expressed not full–fledged by Comenius who has been
described by Howatt (1984) as a genius–the one that the history of
language teaching can claim. And we owe to him more than anyone.
Abstract: This paper analyzes the effect of a single uniform accounting rule on reporting quality by investigating the influence of IFRS on earnings management. This paper examines whether earnings management is reduced after IFRS adoption through the use of “loss avoidance thresholds”, a method that has been verified in earlier studies. This paper concentrates on two European countries: one that represents the continental code law tradition with weak protection of investors (France) and one that represents the Anglo-American common law tradition, which typically implies a strong enforcement system (the United Kingdom).
The research investigates a sample of 526 companies (6822 firm-year observations) during the years 2000 – 2013. The results are different for the two jurisdictions. This study demonstrates that a single set of accounting standards contributes to better reporting quality and reduces the pervasiveness of earnings management in France. In contrast, there is no evidence that a reduction in earnings management followed the implementation of IFRS in the United Kingdom. Due to the fact that IFRS benefit France but not the United Kingdom, other political and economic factors, such legal system or capital market strength, must play a significant role in influencing the comparability and transparency cross-border companies’ financial statements. Overall, the result suggests that IFRS moderately contribute to the accounting quality of reported financial statements and bring benefit for stakeholders, though the role played by other economic factors cannot be discounted.
Abstract: The morphological short-term evolution of Ponta do Tubarão Island (PTI) was investigated through high accurate surveys based on post-processed kinematic (PPK) relative positioning on Global Navigation Satellite Systems (GNSS). PTI is part of a barrier island system on a high energy northeast Brazilian coastal environment and also an area of high environmental sensitivity. Surveys were carried out quarterly over a two years period from May 2010 to May 2012. This paper assesses statically the performance of digital elevation models (DEM) derived from different interpolation methods to represent morphologic features and to quantify volumetric changes and TIN models shown the best results to that purposes. The MDE allowed quantifying surfaces and volumes in detail as well as identifying the most vulnerable segments of the PTI to erosion and/or accumulation of sediments and relate the alterations to climate conditions. The coastal setting and geometry of PTI protects a significant mangrove ecosystem and some oil and gas facilities installed in the vicinities from damaging effects of strong oceanwaves and currents. Thus, the maintenance of PTI is extremely required but the prediction of its longevity is uncertain because results indicate an irregularity of sedimentary balance and a substantial decline in sediment supply to this coastal area.
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: A variety of new technology-based services have
emerged with the development of Information and Communication
Technologies (ICTs). Since technology-based services have technology-driven characteristics, the identification of relationships
between technology-based services and ICTs would give meaningful implications. Thus, this paper proposes an approach for identifying the
relationships between technology-based services and ICTs by
analyzing patent documents. First, business model (BM) patents are
classified into relevant service categories. Second, patent citation
analysis is conducted to investigate the technological linkage and impacts between technology-based services and ICTs at macro level.
Third, as a micro level analysis, patent co-classification analysis is
employed to identify the technological linkage and coverage. The
proposed approach could guide and help managers and designers of
technology-based services to discover the opportunity of the development of new technology-based services in emerging service sectors.
Abstract: Using electrical machine in conventional vehicles, also called hybrid vehicles, has become a promising control scheme that enables some manners for fuel economy and driver assist for better stability. In this paper, vehicle stability control, fuel economy and Driving/Regeneration braking for a 4WD hybrid vehicle is investigated by using an electrical machine on each non-driven wheels. In front wheels driven vehicles, fuel economy and regenerative braking can be obtained by summing torques applied on rear wheels. On the other hand, unequal torques applied to rear wheels provides enhanced safety and path correction in steering. In this paper, a model with fourteen degrees of freedom is considered for vehicle body, tires and, suspension systems. Thereafter, powertrain subsystems are modeled. Considering an electrical machine on each rear wheel, a fuzzy controller is designed for each driving, braking, and stability conditions. Another fuzzy controller recognizes the vehicle requirements between the driving/regeneration and stability modes. Intelligent vehicle control to multi objective operation and forward simulation are the paper advantages. For reaching to these aims, power management control and yaw moment control will be done by three fuzzy controllers. Also, the above mentioned goals are weighted by another fuzzy sub-controller base on vehicle dynamic. Finally, Simulations performed in MATLAB/SIMULINK environment show that the proposed structure can enhance the vehicle performance in different modes effectively.
Abstract: Recently, permeable breakwaters have been suggested to overcome the disadvantages of fully protection breakwaters. These protection structures have minor impacts on the coastal environment and neighboring beaches where they provide a more economical protection from waves and currents. For regular waves, a numerical model is used (FLOW-3D, VOF) to investigate the hydraulic performance of a permeable breakwater. The model of permeable breakwater consists of a pair of identical vertical slotted walls with an impermeable upper and lower part, where the draft is a decimal multiple of the total depth. The middle part is permeable with a porosity of 50%. The second barrier is located at distant of 0.5 and 1.5 of the water depth from the first one. The numerical model is validated by comparisons with previous laboratory data and semi-analytical results of the same model. A good agreement between the numerical results and both laboratory data and semi-analytical results has been shown and the results indicate the applicability of the numerical model to reproduce most of the important features of the interaction. Through the numerical investigation, the friction factor of the model is carefully discussed.
Abstract: In order to evaluation the effects of natural, biological
and chemical fertilizers on grain yield and chickpea quality, field
experiments were carried out in 2007 and 2008 growing seasons. In
this research the effects of different organic, chemical and biological
fertilizers were investigated on grain yield and quality of chickpea.
Experimental units were arranged in split-split plots based on
randomized complete blocks with three replications. The highest
amounts of yield and yield components were obtained in G1×N5
interaction. Significant increasing of N, P, K, Fe and Mg content in
leaves and grains emphasized on superiority of mentioned treatment
because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis ability of the crop. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) had the best grain quality due to high protein, starch
and total sugar contents, low crude fiber and reduced cooking time.
Abstract: Lateral-torsional buckling (LTB) is one of the
phenomenae controlling the ultimate bending strength of steel Ibeams
carrying distributed loads on top flange. Built-up I-sections
are used as main beams and distributors. This study investigates the
ultimate bending strength of such beams with sections of different
classes including slender elements. The nominal strengths of the
selected beams are calculated for different unsupported lengths
according to the Provisions of the American Institute of Steel
Constructions (AISC-LRFD). These calculations are compared with
results of a nonlinear inelastic study using accurate FE model for this
type of loading. The goal is to investigate the performance of the
provisions for the selected sections. Continuous distributed load at
the top flange of the beams was applied at the FE model.
Imperfections of different values are implemented to the FE model to
examine their effect on the LTB of beams at failure, and hence, their
effect on the ultimate strength of beams. The study also introduces a
procedure for evaluating the performance of the provisions compared
with the accurate FEA results of the selected sections. A simplified
design procedure is given and recommendations for future code
updates are made.
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: In this paper channel estimation techniques are
considered as the support methods for OFDM transmission systems
based on Non Binary LDPC (Low Density Parity Check) codes.
Standard frequency domain pilot aided LS (Least Squares) and
LMMSE (Linear Minimum Mean Square Error) estimators are
investigated. Furthermore, an iterative algorithm is proposed as a
solution exploiting the NB-LDPC channel decoder to improve the
performance of the LMMSE estimator. Simulation results of signals
transmitted through fading mobile channels are presented to compare
the performance of the proposed channel estimators.
Abstract: The study aimed to identify the logical structure of
data and particularities of developing and testing a website designed
for selling farm products through online auctions.
The research is based on a short literature review in the field and
exploratory trials of some successful models from other industries, in
order to identify the advantages of using such tool, as well as the
optimal structure and functionality of an auction portal. In the last
part, the study focuses on the results of testing the website by the
potential beneficiaries.
Conclusions of the study underlines that the particularities of some
agricultural products could raise difficulties in the process of selling
them through online auctions, but the use of such system it is
perceived to bring significant improvements in the supply chain.
The results of scientific investigations require a more detailed
study regarding the importance of using quality standards for
agricultural products sold via online auction, the impact that
implementation of an online payment system could have on trade
with agricultural products and problems which could arise in using
the website in different countries.