Abstract: The Metropolitan Region of Sao Paulo (MRSP) has suffered from serious water scarcity. Consequently, the most convenient solution has been building wells to extract groundwater from local aquifers. However, it requires constant vigilance to prevent over extraction and future events that can pose serious threat to the population, such as subsidence. Radar imaging techniques (InSAR) have allowed continuous investigation of such phenomena. The analysis of data in the present study consists of 23 SAR images dated from October 2007 to March 2011, obtained by the ALOS-1 spacecraft. Data processing was made with the software GMTSAR, by using the InSAR technique to create pairs of interferograms with ground displacement during different time spans. First results show a correlation between the location of 102 wells registered in 2009 and signals of ground displacement equal or lower than -90 millimeters (mm) in the region. The longest time span interferogram obtained dates from October 2007 to March 2010. As a result, from that interferogram, it was possible to detect the average velocity of displacement in millimeters per year (mm/y), and which areas strong signals have persisted in the MRSP. Four specific areas with signals of subsidence of 28 mm/y to 40 mm/y were chosen to investigate the phenomenon: Guarulhos (Sao Paulo International Airport), the Greater Sao Paulo, Itaquera and Sao Caetano do Sul. The coverage area of the signals was between 0.6 km and 1.65 km of length. All areas are located above a sedimentary type of aquifer. Itaquera and Sao Caetano do Sul showed signals varying from 28 mm/y to 32 mm/y. On the other hand, the places most likely to be suffering from stronger subsidence are the ones in the Greater Sao Paulo and Guarulhos, right beside the International Airport of Sao Paulo. The rate of displacement observed in both regions goes from 35 mm/y to 40 mm/y. Previous investigations of the water use at the International Airport highlight the risks of excessive water extraction that was being done through 9 deep wells. Therefore, it is affirmed that subsidence events are likely to occur and to cause serious damage in the area. This study could show a situation that has not been explored with proper importance in the city, given its social and economic consequences. Since the data were only available until 2011, the question that remains is if the situation still persists. It could be reaffirmed, however, a scenario of risk at the International Airport of Sao Paulo that needs further investigation.
Abstract: Soil improvement using vibro stone column techniques consists of two main parts: (1) the installed load bearing columns of well-compacted, coarse-grained material and (2) the improvements to the surrounding soil due to vibro compaction. Extensive research work has been carried out over the last 20 years to understand the improvement in the composite foundation performance due to the second part mentioned above. Nevertheless, few of these studies have tried to quantify some of the key design parameters, namely the changes in the stiffness and stress state of the treated soil, or have consider these parameters in the design and calculation process. Consequently, empirical and conservative design methods are still being used by ground improvement companies with a significant variety of results in engineering practice. Two-dimensional finite element study to develop an axisymmetric model of a single stone column reinforced foundation was performed using PLAXIS 2D AE to quantify the effect of the vibro installation of this column in soft saturated clay. Settlement and bearing performance were studied as an essential part of the design and calculation of the stone column foundation. Particular attention was paid to the large deformation in the soft clay around the installed column caused by the lateral expansion. So updated mesh advanced option was taken in the analysis. In this analysis, different degrees of stone column lateral expansions were simulated and numerically analyzed, and then the changes in the stress state, stiffness, settlement performance and bearing capacity were quantified. It was found that application of radial expansion will produce a horizontal stress in the soft clay mass that gradually decrease as the distance from the stone column axis increases. The excess pore pressure due to the undrained conditions starts to dissipate immediately after finishing the column installation, allowing the horizontal stress to relax. Changes in the coefficient of the lateral earth pressure K ٭, which is very important in representing the stress state, and the new stiffness distribution in the reinforced clay mass, were estimated. More encouraging results showed that increasing the expansion during column installation has a noticeable effect on improving the bearing capacity and reducing the settlement of reinforced ground, So, a design method should include this significant effect of the applied lateral displacement during the stone column instillation in simulation and numerical analysis design.
Abstract: In this paper proposed the effective fault detection of industrial drives by using Biorthogonal Posterior Vibration Signal-Data Probabilistic Wavelet Neural Network (BPPVS-WNN) system. This system was focused to reducing the current flow and to identify faults with lesser execution time with harmonic values obtained through fifth derivative. Initially, the construction of Biorthogonal vibration signal-data based wavelet transform in BPPVS-WNN system localizes the time and frequency domain. The Biorthogonal wavelet approximates the broken bearing using double scaling and factor, identifies the transient disturbance due to fault on induction motor through approximate coefficients and detailed coefficient. Posterior Probabilistic Neural Network detects the final level of faults using the detailed coefficient till fifth derivative and the results obtained through it at a faster rate at constant frequency signal on the industrial drive. Experiment through the Simulink tool detects the healthy and unhealthy motor on measuring parametric factors such as fault detection rate based on time, current flow rate, and execution time.
Abstract: Nowadays, ontologies are used for achieving a
common understanding within a user community and for sharing
domain knowledge. However, the de-centralized nature of the web
makes indeed inevitable that small communities will use their own
ontologies to describe their data and to index their own resources.
Certainly, accessing to resources from various ontologies created
independently is an important challenge for answering end user
queries. Ontology mapping is thus required for combining ontologies.
However, mapping complete ontologies at run time is a
computationally expensive task. This paper proposes a system in
which mappings between concepts may be generated dynamically as
the concepts are encountered during user queries. In this way, the
interaction itself defines the context in which small and relevant
portions of ontologies are mapped. We illustrate application of the
proposed system in the context of Technology Enhanced Learning
(TEL) where learners need to access to learning resources covering
specific concepts.
Abstract: Augmented and Virtual Realties is quickly becoming
a hotbed of activity with millions of dollars being spent on R & D
and companies such as Google and Microsoft rushing to stake their
claim. Augmented reality (AR) is however marching ahead due to the
spread of the ideal AR device – the smartphone. Despite its potential,
there remains a deep digital divide between the Developed and
Developing Countries. The Technological Acceptance Model (TAM)
and Hofstede cultural dimensions also predict the behaviour intention
to uptake AR in India will be large. This paper takes a quantified
approach by collecting 340 survey responses to AR scenarios and
analyzing them through statistics. The Survey responses show that
the Intention to Use, Perceived Usefulness and Perceived Enjoyment
dimensions are high among the urban population in India. This along
with the exponential smartphone indicates that India is on the cusp of
a boom in the AR sector.
Abstract: This study examined the digital preservation in
Nigeria university libraries. A comparison between the university of
Nigeria Nsukka (UNN) and Ahmadu Bello University Zaria (ABU,
Zaria). The study utilized primary source of data obtained from two
selected institution librarians. Finding revealed varying results in
terms of skills acquired by librarians before and after digitization of
the two institutions. The study reports that journals publication, text
book, CD-ROMS, conference papers and proceedings, theses,
dissertations and seminar papers are among the information resources
available for digitization. The study further documents that copyright
issue, power failure, and unavailability of needed materials are
among the challenges facing the digitization of library of the
institution. On the basis of the finding, the study concluded that
digitization of library enhances efficiency in organization and
retrieval of information services. The study therefore recommended
that software should be upgraded with backup, training of the
librarians on digital process, installation of antivirus and
enhancement of technical collaboration between the library and MIS.
Abstract: Approximately 10,000 different types of dyes and
pigments are being used in various industrial applications yearly,
which include the textile and printing industries. However, these dyes
are difficult to degrade naturally once they enter the aquatic system.
Their high persistency in natural environment poses a potential health
hazard to all form of life. Hence, there is a need for alternative dye
removal strategy in the environment via bioremediation. In this study,
fungi laccase is investigated via commercial agar dyes plates and
submerged fermentation to explore the application of fungi laccase in
textile dye wastewater treatment. Two locally isolated basidiomycetes
were screened for laccase activity using media added with commercial
dyes such as 2, 2-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid
(ABTS), guaiacol and Remazol Brillant Blue R (RBBR). Isolate TBB3
(1.70±0.06) and EL2 (1.78±0.08) gave the highest results for ABTS
plates with the appearance of greenish halo on around the isolates.
Submerged fermentation performed on Isolate TBB3 with the
productivity 3.9067 U/ml/day, whereas the laccase activity for Isolate
EL2 was much lower (0.2097 U/ml/day). As isolate TBB3 showed
higher laccase production, it was subjected to molecular
characterization by DNA isolation, PCR amplification and sequencing
of ITS region of nuclear ribosomal DNA. After being compared with
other sequences in National Center for Biotechnology Information
(NCBI database), isolate TBB3 is probably from species Trametes
hirsutei. Further research work can be performed on this isolate by
upscale the production of laccase in order to meet the demands of the
requirement for higher enzyme titer for the bioremediation of textile
dyes.
Abstract: The present study investigated the protective effect of
thymoquinone (TQ), against cadmium-induced kidney injury in rats.
Cadmium chloride (1.2 mg Cd/kg/day, s.c.), was given for nine
weeks. TQ treatment (40 mg/kg/day, p.o.) started on the same day of
cadmium administration and continued for nine weeks. TQ
significantly decreased serum creatinine, renal malondialdehyde and
nitric oxide, and significantly increased renal reduced glutathione in
rats received cadmium. Histopathological examination showed that
TQ markedly minimized renal tissue damage induced by cadmium.
Immunohistochemical analysis revealed that TQ markedly decreased
the cadmium-induced expression of inducible nitric oxide synthase,
tumor necrosis factor-α, cyclooxygenase-2, and caspase-3 in renal
tissue. It was concluded that TQ significantly protected against
cadmium nephrotoxicity in rats, through its antioxidant, antiinflammatory,
and antiapoptotic actions.
Abstract: This case study used the action research concept as a tool to integrate the innovation in a learning experience on a design course. The action research was investigated at Prince Sultan University, College of Engineering in the Interior Design and Architecture Department in January 2015, through the Higher Education Academy program. The action research was presented first with the definition of the research, leading to how it was used and how solutions were found. It concluded by showing that once the action research application in interior design and architecture were studied it was an effective tool to improve student’s learning, develop their practice in design courses, and it discussed the negative and positive issues that were encountered.
Abstract: Introduction: This work is aimed to represent the use of the OPTI-JET CS MD1 MR prototype for application of neutral electrolyzed oxidizing water (NEOW) in magnetic resonance rooms. Material and Methods: We produced and used OPTI-JET CS MD1 MR aerosolisator whereby was performed aerosolization. The presence of microorganisms before and after the aerosolisation was recorded with the help of cyclone air sampling. Colony formed units (CFU) was counted. Results: The number of microorganisms in magnetic resonance 3T room was low as expected. Nevertheless, a possible CFU reduction of 87% was recorded. Conclusions: The research has shown that the use of EOW for the air and hard surface disinfection can considerably reduce the presence of microorganisms and consequently the possibility of hospital infections. It has also demonstrated that the use of OPTI-JET CS MD1 MR is very good. With this research, we started new guidelines for aerosolization in magnetic resonance rooms. Future work: We predict that presented technique works very good but we must focus also on time capacity sensors, and new appropriate toxicological studies.
Abstract: Recently, the world main problem is a global warming and climate change affecting both outdoor and indoor environments, especially the air quality (AQ) as a result of vast migration of people from rural areas to urban areas. Therefore, cities became more crowded and denser from an irregular population increase, along with increasing urbanization caused many problems for the environment such as increasing the land prices, changes in life style, and the new buildings are not adapted to the climate producing uncomfortable and unhealthy indoor building conditions. As interior environments are the places that create the most intimate relationship with the user. Consequently, the indoor environment quality (IEQ) for buildings became uncomfortable and unhealthy for its occupants. The symptoms commonly associated with poor indoor environment such as itchy, headache, fatigue, and respiratory complaints such as cough and congestion, etc. The symptoms tend to improve over time or even disappear when people are away from the building. Therefore, designing a healthy indoor environment to fulfill human needs is the main concern for architects and interior designer. However, this research explores how occupant expectations and environmental attitudes may influence occupant health and satisfaction within the context of the indoor environment. In doing so, it reviews and contributes to the methods and tools used to evaluate only the indoor environment quality (IEQ) components of building performance. Its main aim is to review the literature on indoor human comfort. This is followed by a review of previous papers published related to human comfort. Finally, this paper will provide possible approaches in design level of healthy buildings.
Abstract: In this work, we use the Fault detection and isolation and the Fault tolerant control based on sliding mode observer in order to introduce the well diagnosis of a nonlinear system. The robustness of the proposed observer for the two techniques is tested through a physical example. The results in this paper show the interaction between the Fault tolerant control and the Diagnosis procedure.
Abstract: In subjective terms, Polish SME sector occupies a
prominent position in the national economic development, in which
planning of the management strategies should be primarily based on
identifying and meeting the innovation needs. As a research sample, there is chosen a printing sector of industry.
SMEs share in printing sector in Poland is estimated at the level of
81% of all enterprises. In recent years, the printing industry achieved
one of the highest levels of EU support in Poland. There is a
relatively high increase in the development of technological
innovations in equipment and the associated significant increase in
production capacity. It can be also noticed that on average, every
third enterprise belonging to the printing industry has implemented
innovations, but not all of them effected in better economic results.
Therefore, the aim of this article is to evaluate the impact of the
implementation of innovation projects financed from the EU funds
for performance of SMEs in the printing industry. As the results of research of EU funds co-financing effects on the
development of innovation in the printing industry, it was specified
that examined SMEs prefer to implement product innovation to
receive a grant to the project at a level between 40% to 60%, the
remaining part of the investment is usually covered with equity. The most common type of innovation had indicated a single
implementation, related only to the change in process, technology, or
organization. The relationship between variables of the EU funds and
management of innovative activities was verified. It has been
observed that the identified variables arising from the support in a
form of the EU funds had a positive effect on the level of earned
revenue, the increase in margin and in increase in employment as
well. It was confirmed that the implemented innovations supported
by the European funds have a positive impact on the performance of
the printing companies. Although there is a risk that due to the
decreasing demand for printing services such a high level of funding
the companies in this sector will significantly increase competition in
the long term, that may also contribute to the economic problems of
the enterprises belonging to the analyzed branch.
Abstract: Automatic License plate recognition (ALPR) is a technology which recognizes the registration plate or number plate or License plate of a vehicle. In this paper, an Indian vehicle number plate is mined and the characters are predicted in efficient manner. ALPR involves four major technique i) Pre-processing ii) License Plate Location Identification iii) Individual Character Segmentation iv) Character Recognition. The opening phase, named pre-processing helps to remove noises and enhances the quality of the image using the conception of Morphological Operation and Image subtraction. The second phase, the most puzzling stage ascertain the location of license plate using the protocol Canny Edge detection, dilation and erosion. In the third phase, each characters characterized by Connected Component Approach (CCA) and in the ending phase, each segmented characters are conceptualized using cross correlation template matching- a scheme specifically appropriate for fixed format. Major application of ALPR is Tolling collection, Border Control, Parking, Stolen cars, Enforcement, Access Control, Traffic control. The database consists of 500 car images taken under dissimilar lighting condition is used. The efficiency of the system is 97%. Our future focus is Indian Vehicle License Plate Validation (Whether License plate of a vehicle is as per Road transport and highway standard).
Abstract: This work studies the effect of thickness on structural
and electrical properties of CuAlS2 thin films grown by two stage
vacuum thermal evaporation technique. CuAlS2 thin films of
thicknesses 50nm, 100nm and 200nm were deposited on suitably
cleaned corning 7059 glass substrate at room temperature (RT). In
the first stage Cu-Al precursors were grown at room temperature by
thermal evaporation and in the second stage Cu-Al precursors were
converted to CuAlS2 thin films by sulfurisation under sulfur
atmosphere at the temperature of 673K. The structural properties of
the films were examined by X-ray diffraction (XRD) technique while
electrical properties of the specimens were studied using four point
probe method. The XRD studies revealed that the films are of
crystalline in nature having tetragonal structure. The variations of the
micro-structural parameters, such as crystallite size (D), dislocation
density ( ), and micro-strain ( ), with film thickness were
investigated. The results showed that the crystallite sizes increase as
the thickness of the film increases. The dislocation density and
micro-strain decreases as the thickness increases. The resistivity ( )
of CuAlS2 film is found to decrease with increase in film thickness,
which is related to the increase of carrier concentration with film
thickness. Thus thicker films exhibit the lowest resistivity and high
carrier concentration, implying these are the most conductive films.
Low electrical resistivity and high carrier concentration are widely
used as the essential components in various optoelectronic devices
such as light-emitting diode and photovoltaic cells.
Abstract: Pipelines are extensively used engineering structures
which convey fluid from one place to another. Most of the time,
pipelines are placed underground and are encumbered by soil weight
and traffic loads. Corrosion of pipe material is the most common
form of pipeline deterioration and should be considered in both the
strength and serviceability analysis of pipes.
The study in this research focuses on concrete pipes in sewage
systems (concrete sewers). This research firstly investigates how to
involve the effect of corrosion as a time dependent process of
deterioration in the structural and failure analysis of this type of pipe.
Then three probabilistic time dependent reliability analysis methods
including the first passage probability theory, the gamma distributed
degradation model and the Monte Carlo simulation technique are
discussed and developed. Sensitivity analysis indexes which can be
used to identify the most important parameters that affect pipe failure
are also discussed.
The reliability analysis methods developed in this paper contribute
as rational tools for decision makers with regard to the strengthening
and rehabilitation of existing pipelines. The results can be used to
obtain a cost-effective strategy for the management of the sewer
system.
Abstract: This paper has focused on the most important parameters in the LSC uptake; inlet Re number and Sc number in the presence of non-uniform magnetic field. The magnetic field is arising from the thin wire with electric current placed vertically to the arterial blood vessel. According to the results of this study, applying magnetic field can be a treatment for atherosclerosis by reducing LSC along the vessel wall. Homogeneous porous layer as a arterial wall has been regarded. Blood flow has been considered laminar and incompressible containing Ferro fluid (blood and 4 % vol. Fe3O4) under steady state conditions. Numerical solution of governing equations was obtained by using the single-phase model and control volume technique for flow field.
Abstract: Problem of food preservation is extremely important
for mankind. Viscous damage ("illness") of bread results from
development of Bacillus spp. bacteria. High temperature resistant
spores of this microorganism are steady against 120°C) and remain in
bread during pastries, potentially causing spoilage of the final
product. Scientists are interested in further characterization of bread
spoiling Bacillus spp. species. Our aim was to find weather yeast
Saccharomyces cerevisiae strains that are able to produce natural
antimicrobial killer factor can preserve bread illness. By diffusion
method, we showed yeast antagonistic activity against spore-forming
bacteria. Experimental technological parameters were the same as for
bakers' yeasts production on the industrial scale. Risograph test
during dough fermentation demonstrated gas production. The major
finding of the study was a clear indication of the presence of killer
yeast strain antagonistic activity against rope in bread causing
bacteria. After demonstrating antagonistic effect of S. cerevisiae on
bacteria using solid nutrient medium, we tested baked bread under
provocative conditions. We also measured formation of carbon
dioxide in the dough, dough-making duration and quality of the final
products, when using different strains of S. cerevisiae. It is
determined that the use of yeast S. cerevisiae RCAM 01730 killer
strain inhibits appearance of rope in bread. Thus, natural yeast
antimicrobial killer toxin, produced by some S. cerevisiae strains is
an anti-rope in bread protector.
Abstract: Feedback is a vital element for improving student
learning in a simulation-based training as it guides and refines
learning through scaffolding. A number of studies in literature have
shown that students’ learning is enhanced when feedback is provided
with personalized tutoring that offers specific guidance and adapts
feedback to the learner in a one-to-one environment. Thus, emulating
these adaptive aspects of human tutoring in simulation provides an
effective methodology to train individuals. This paper presents the results of a study that investigated the
effectiveness of automating different types of feedback techniques
such as Knowledge-of-Correct-Response (KCR) and Answer-Until-
Correct (AUC) in software simulation for learning basic information
technology concepts. For the purpose of comparison, techniques like
simulation with zero or no-feedback (NFB) and traditional hands-on
(HON) learning environments are also examined. The paper presents the summary of findings based on quantitative
analyses which reveal that the simulation based instructional
strategies are at least as effective as hands-on teaching methodologies
for the purpose of learning of IT concepts. The paper also compares
the results of the study with the earlier studies and recommends
strategies for using feedback mechanism to improve students’
learning in designing and simulation-based IT training.
Abstract: AmI proposes a new way of thinking about computers, which follows the ideas of the Ubiquitous Computing vision of Mark Weiser. In these, there is what is known as a Disappearing Computer Initiative, with users immersed in intelligent environments. Hence, technologies need to be adapted so that they are capable of replacing the traditional inputs to the system by embedding these in every-day artifacts. In this work, we present an approach, which uses Radiofrequency Identification (RFID) and Near Field Communication (NFC) technologies. In the latter, a new form of interaction appears by contact. We compare both technologies by analyzing their requirements and advantages. In addition, we propose using a combination of RFID and NFC.