Abstract: the reliability analysis of the medical equipments can
help to increase the availability and the efficiency of the systems. In
this manuscript we present a simple method of decomposition that
could be easily applied on the complex medical systems. Using this
method we can easily calculate the effect of the subsystems or
components on the reliability of the overall system. Furthermore, to
investigate the effect of subsystems or components on system
performance, we perform a numerical study varying every time the
worst reliability of subsystem or component with another which has
higher reliability. It can also be useful to engineers and designers of
medical equipment, who wishes to optimize the complex systems.
Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: Security management has changed from the
management of security equipments and useful interface to manager.
It analyzes the whole security conditions of network and preserves the
network services from attacks. Secure router technology has security
functions, such as intrusion detection, IPsec(IP Security) and access
control, are applied to legacy router for secure networking. It controls
an unauthorized router access and detects an illegal network intrusion.
This paper relates to a security engine management of router based on
a security policy, which is the definition of security function against a
network intrusion. This paper explains the security policy and designs
the structure of security engine management framework.
Abstract: Low power consumption is a major constraint for battery-powered system like computer notebook or PDA. In the past, specialists usually designed both specific optimized equipments and codes to relief this concern. Doing like this could work for quite a long time, however, in this era, there is another significant restraint, the time to market. To be able to serve along the power constraint while can launch products in shorter production period, objectoriented programming (OOP) has stepped in to this field. Though everyone knows that OOP has quite much more overhead than assembly and procedural languages, development trend still heads to this new world, which contradicts with the target of low power consumption. Most of the prior power related software researches reported that OOP consumed much resource, however, as industry had to accept it due to business reasons, up to now, no papers yet had mentioned about how to choose the best OOP practice in this power limited boundary. This article is the pioneer that tries to specify and propose the optimized strategy in writing OOP software under energy concerned environment, based on quantitative real results. The language chosen for studying is C# based on .NET Framework 2.0 which is one of the trendy OOP development environments. The recommendation gotten from this research would be a good roadmap that can help developers in coding that well balances between time to market and time of battery.
Abstract: The myoelectric signal (MES) is one of the Biosignals
utilized in helping humans to control equipments. Recent approaches
in MES classification to control prosthetic devices employing pattern
recognition techniques revealed two problems, first, the classification
performance of the system starts degrading when the number of
motion classes to be classified increases, second, in order to solve the
first problem, additional complicated methods were utilized which
increase the computational cost of a multifunction myoelectric
control system. In an effort to solve these problems and to achieve a
feasible design for real time implementation with high overall
accuracy, this paper presents a new method for feature extraction in
MES recognition systems. The method works by extracting features
using Wavelet Packet Transform (WPT) applied on the MES from
multiple channels, and then employs Fuzzy c-means (FCM)
algorithm to generate a measure that judges on features suitability for
classification. Finally, Principle Component Analysis (PCA) is
utilized to reduce the size of the data before computing the
classification accuracy with a multilayer perceptron neural network.
The proposed system produces powerful classification results (99%
accuracy) by using only a small portion of the original feature set.
Abstract: Artifact is one of the most important factors in
degrading the CT image quality and plays an important role in
diagnostic accuracy. In this paper, some artifacts typically appear in
Spiral CT are introduced. The different factors such as patient,
equipment and interpolation algorithm which cause the artifacts are
discussed and new developments and image processing algorithms to
prevent or reduce them are presented.
Abstract: In aircraft applications, according to the nature of
electrical equipment its location may be in unpressurized area or very
close to the engine; thus, the environmental conditions may change
from atmospheric pressure to less than 100 mbar, and the temperature
may be higher than the ambient one as in most real working
conditions of electrical equipment. Then, the classical Paschen curve
has to be replotted since these parameters may affect the discharge
ignition voltage. In this paper, we firstly investigate the domain of
validity of two corrective expressions on the Paschen-s law found in
the literature, in case of changing the air environment and known as
Peek and Dunbar corrections. Results show that these corrections are
no longer valid for combined variation of temperature and pressure.
After that, a new empirical expression for breakdown voltage is
proposed and is validated in the case of combined variations of
temperature and pressure.
Abstract: Since the last two decades, container transportation
system has been faced under increasing development. This fact
shows the importance of container transportation system as a key role
of container terminals to link between sea and land. Therefore, there
is a continuous need for the optimal use of equipment and facilities in
the ports. Regarding the complex structure of container ports, this
paper presents a simulation model that compares tow storage
strategies for storing containers in the yard. For this purpose, we
considered loading and unloading norm as an important criterion to
evaluate the performance of Shahid Rajaee container port. By
analysing the results of the model, it will be shown that using
marshalling yard policy instead of current storage system has a
significant effect on the performance level of the port and can
increase the loading and unloading norm up to 14%.
Abstract: EEG signal is one of the oldest measures of brain
activity that has been used vastly for clinical diagnoses and
biomedical researches. However, EEG signals are highly
contaminated with various artifacts, both from the subject and from
equipment interferences. Among these various kinds of artifacts,
ocular noise is the most important one. Since many applications such
as BCI require online and real-time processing of EEG signal, it is
ideal if the removal of artifacts is performed in an online fashion.
Recently, some methods for online ocular artifact removing have
been proposed. One of these methods is ARMAX modeling of EEG
signal. This method assumes that the recorded EEG signal is a
combination of EOG artifacts and the background EEG. Then the
background EEG is estimated via estimation of ARMAX parameters.
The other recently proposed method is based on adaptive filtering.
This method uses EOG signal as the reference input and subtracts
EOG artifacts from recorded EEG signals. In this paper we
investigate the efficiency of each method for removing of EOG
artifacts. A comparison is made between these two methods. Our
undertaken conclusion from this comparison is that adaptive filtering
method has better results compared with the results achieved by
ARMAX modeling.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
relationship between the minimum direct and indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of direct and indirect jerks are found using the dynamic optimization
methods together with the numerical approximation. This is to allow
us to simulate and compare visually and statistically the time history
of control inputs employed by minimum direct and indirect jerk
designs. By considering minimum indirect jerk problem, the
numerical solution becomes much easier and yields to the similar
results as minimum direct jerk problem.
Abstract: In the upstream we place a piece of ring and rotate
it with 83Hz, 166Hz, 333Hz,and 666H to find the effect of the
periodic distortion.In the experiment this type of the perturbation
will not allow since the mechanical failure of any parts of the
equipment in the upstream will destroy the blade system. This type of
study will be only possible by CFD. We use two pumps NS32
(ENSAM) and three blades pump (Tamagawa Univ). The benchmark
computations were performed without perturbation parts, and confirm
the computational results well agreement in head-flow rate. We
obtained the pressure fluctuation growth rate that is representing the
global instability of the turbo-system. The fluctuating torque
components were 0.01Nm(5000rpm), 0.1Nm(10000rmp),
0.04Nm(20000rmp), 0.15Nm( 40000rmp) respectively. Only for
10000rpm(166Hz) the output toque was random, and it implies that it
creates unsteady flow by separations on the blades, and will reduce the
pressure loss significantly
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: The current trend of increasing quality and demands
of the final product is affected by time analysis of the entire
manufacturing process. The primary requirement of manufacturing is
to produce as many products as soon as possible, at the lowest
possible cost, but of course with the highest quality. Such
requirements may be satisfied only if all the elements entering and
affecting the production cycle are in a fully functional condition.
These elements consist of sensory equipment and intelligent control
elements that are essential for building intelligent manufacturing
systems. The intelligent manufacturing paradigm includes a new
approach to production system structure design. Intelligent behaviors
are based on the monitoring of important parameters of system and
its environment. The flexible reaction to changes. The realization and
utilization of this design paradigm as an "intelligent manufacturing
system" enables the flexible system reaction to production
requirement as soon as environmental changes too. Results of these
flexible reactions are a smaller layout space, be decreasing of
production and investment costs and be increasing of productivity.
Intelligent manufacturing system itself should be a system that can
flexibly respond to changes in entering and exiting the process in
interaction with the surroundings.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: In most cases, it is considerably difficult to directly measure structural vibration with a lot of sensors because of complex
geometry, time and equipment cost. For this reason, this paper deals
with the problem of locating sensors on a plate model by four advanced sensor placement optimization (S.P.O) techniques. It also
suggests the evaluation index representing the characteristic of orthogonal between each of natural modes. The index value provides the assistance to selecting of proper S.P.O technique and optimal
positions for monitoring of dynamic systems without the experiment.
Abstract: The aim of the article is to describe modern
contemporary systems of employees' remuneration used in
organizations, to give a general overview of these questions based on
the questionnaire survey made by the authors, as well as to assess
possible effects of economic crisis in this area. It is necessary to be
aware of the fact that firm's success in the contemporary business
environment depends not only on the technical equipment, financial
resources, availability of raw materials and information and effective
management, but one of the crucial factors of firm's success is its
human potential. The article emphasizes that the well working
remuneration system has a very important position in the
organization in the broadest sense. The paper also aims to the current
situation in the area of employees' remuneration in one of Czech
Republic regions, in the Moravian-Silesian Region.
Abstract: Paper is dealing with vulnerability concerning elements of hydrological structures and elements of technological equipments which are acceptable for groundwater resources. The vulnerability assessment stems from the application of the register of hazards and a potential threat to individual water source elements within each type of hazard. The proposed procedure is pattern for assessing the risks of disturbance, damage, or destruction of water source by the identified natural or technological hazards and consequently for classification of these risks in relation to emergency water supply. Using of this procedure was verified on selected groundwater resource in particular region, which seems to be as potentially useful for crisis planning system.
Abstract: Increasing use of cell phone as a medium of human interaction is playing a vital role in solving riddles of crime as well. A young girl went missing from her home late in the evening in the month of August, 2008 when her enraged relatives and villagers physically assaulted and chased her fiancée who often frequented her home. Two years later, her mother lodged a complaint against the relatives and the villagers alleging that after abduction her daughter was either sold or killed as she had failed to trace her. On investigation, a rusted cell phone with partial visible IMEI number, clothes, bangles, human skeleton etc. recovered from abandoned well in the month of May, 2011 were examined in the lab. All hopes pinned on identity of cell phone, for only linking evidence to fix the scene of occurrence supported by call detail record (CDR) and to dispel doubts about mode of sudden disappearance or death as DNA technology did not help in establishing identity of the deceased. The conventional scientific methods were used without success and international mobile equipment identification number of the cell phone could be generated by using statistical analysis followed by online verification.
Abstract: Energy generated by the force of water in hydropower
can provide a more sustainable, non-polluting alternative to fossil
fuels, along with other renewable sources of energy, such as wind,
solar and tidal power, bio energy and geothermal energy. Small scale
hydroelectricity in Iran is well suited for “off-grid" rural electricity
applications, while other renewable energy sources, such as wind,
solar and biomass, can be beneficially used as fuel for pumping
groundwater for drinking and small scale irrigation in remote rural
areas or small villages. Small Hydro Power plants in Iran have very
low operating and maintenance costs because they consume no fossil
or nuclear fuel and do not involve high temperature processes. The
equipment is relatively simple to operate and maintain. Hydropower
equipment can adjust rapidly to load changes. The extended
equipment life provides significant economic advantages. Some
hydroelectric plants installed 100 years ago still operate reliably. The
Polkolo river is located on Karun basin at southwest of Iran. Situation
and conditions of Polkolo river are evaluated for construction of
small hydropower in this article. The topographical conditions and
the existence of permanent water from springs provide the suitability
to install hydroelectric power plants on the river Polkolo. The
cascade plant consists of 9 power plants connected with each other
and is having the total head as 1100m and discharge about 2.5cubic
meter per second. The annual production of energy is 105.5 million
kwh.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.