Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: Lead time is a critical measure of a supply chain's
performance. It impacts both the customer satisfactions as well as the
total cost of inventory. This paper presents the result of a study on the
analysis of the customer order lead-time for a multinational company.
In the study, the lead time was divided into three stages respectively:
order entry, order fulfillment, and order delivery. A sample of size 2,425 order lines was extracted from the
company's records to use for this study. The sample data entails
information regarding customer orders from the time of order entry
until order delivery. Data regarding the lead time of each stage for
different orders were also provided. Summary statistics on lead time
data reveals that about 30% of the orders were delivered later than the
scheduled due date. The result of the multiple linear regression
analysis technique revealed that component type, logistics parameter,
order size and the customer type have significant impacts on lead
time. Data analysis on the stages of lead time indicates that stage 2
consumed over 50% of the lead time. Pareto analysis was made to
study the reasons for the customer order delay in each stage.
Recommendation was given to resolve the problem.
Abstract: Accurate forecasting of fresh produce demand is one
the challenges faced by Small Medium Enterprise (SME)
wholesalers. This paper is an attempt to understand the cause for the
high level of variability such as weather, holidays etc., in demand of
SME wholesalers. Therefore, understanding the significance of
unidentified factors may improve the forecasting accuracy. This
paper presents the current literature on the factors used to predict
demand and the existing forecasting techniques of short shelf life
products. It then investigates a variety of internal and external
possible factors, some of which is not used by other researchers in the
demand prediction process. The results presented in this paper are
further analysed using a number of techniques to minimize noise in
the data. For the analysis past sales data (January 2009 to May 2014)
from a UK based SME wholesaler is used and the results presented
are limited to product ‘Milk’ focused on café’s in derby. The
correlation analysis is done to check the dependencies of variability
factor on the actual demand. Further PCA analysis is done to
understand the significance of factors identified using correlation.
The PCA results suggest that the cloud cover, weather summary and
temperature are the most significant factors that can be used in
forecasting the demand. The correlation of the above three factors
increased relative to monthly and becomes more stable compared to
the weekly and daily demand.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.
Abstract: Optic disk segmentation plays a key role in the mass
screening of individuals with diabetic retinopathy and glaucoma
ailments. An efficient hardware-based algorithm for optic disk
localization and segmentation would aid for developing an automated
retinal image analysis system for real time applications. Herein,
TMS320C6416DSK DSP board pixel intensity based fractal analysis
algorithm for an automatic localization and segmentation of the optic
disk is reported. The experiment has been performed on color and
fluorescent angiography retinal fundus images. Initially, the images
were pre-processed to reduce the noise and enhance the quality. The
retinal vascular tree of the image was then extracted using canny
edge detection technique. Finally, a pixel intensity based fractal
analysis is performed to segment the optic disk by tracing the origin
of the vascular tree. The proposed method is examined on three
publicly available data sets of the retinal image and also with the data
set obtained from an eye clinic. The average accuracy achieved is
96.2%. To the best of the knowledge, this is the first work reporting
the use of TMS320C6416DSK DSP board and pixel intensity based
fractal analysis algorithm for an automatic localization and
segmentation of the optic disk. This will pave the way for developing
devices for detection of retinal diseases in the future.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: In Electric Power Steering (EPS), spoke type
Brushless AC (BLAC) motors offer distinct advantages over other
electric motor types in terms torque smoothness, reliability and
efficiency. This paper deals with the shape optimization of spoke
type BLAC motor, in order to reduce cogging torque. This paper
examines 3 steps skewing rotor angle, optimizing rotor core edge and
rotor overlap length for reducing cogging torque in spoke type BLAC
motor. The methods were applied to existing machine designs and
their performance was calculated using finite- element analysis
(FEA). Prototypes of the machine designs were constructed and
experimental results obtained. It is shown that the FEA predicted the
cogging torque to be nearly reduce using those methods.
Abstract: Cyber exercises used to assess the preparedness of a
community against cyber crises, technology failures and Critical
Information Infrastructure (CII) incidents. The cyber exercises also
called cyber crisis exercise or cyber drill, involved partnerships or
collaboration of public and private agencies from several sectors.
This study investigates Organisation Cyber Resilience (OCR) of
participation sectors in cyber exercise called X Maya in Malaysia.
This study used a principal based cyber resilience survey called CSuite
Executive checklist developed by World Economic Forum in
2012. To ensure suitability of the survey to investigate the OCR, the
reliability test was conducted on C-Suite Executive checklist items.
The research further investigates the differences of OCR in ten
Critical National Infrastructure Information (CNII) sectors
participated in the cyber exercise. The One Way ANOVA test result
showed a statistically significant difference of OCR among ten CNII
sectors participated in the cyber exercise.
Abstract: Despite the advances made in various new
technologies, application of these technologies for agriculture still
remains a formidable task, as it involves integration of diverse
domains for monitoring the different process involved in agricultural
management. Advances in ambient intelligence technology represents
one of the most powerful technology for increasing the yield of
agricultural crops and to mitigate the impact of water scarcity,
climatic change and methods for managing pests, weeds and diseases.
This paper proposes a GPS-assisted, machine to machine solutions
that combine information collected by multiple sensors for the
automated management of paddy crops. To maintain the economic
viability of paddy cultivation, the various techniques used in
agriculture are discussed and a novel system which uses ambient
intelligence technique is proposed in this paper. The ambient
intelligence based agricultural system gives a great scope.
Abstract: The environmental, cultural, social, and technological
changes have led higher education institutes to question their
traditional roles. Many declarations and frameworks highlight the
importance of fulfilling social responsibility of higher education
institutes. The study aims at developing a framework of university
social responsibility and sustainability (USR&S) with focus on South
Valley University (SVU) as a case study of Egyptian Universities.
The study used meetings with 12 vice deans of community services
and environmental affairs on social responsibility and environmental
issues. The proposed framework integrates social responsibility with
strategic management through the establishment and maintenance of
the vision, mission, values, goals and management systems;
elaboration of policies; provision of actions; evaluation of services
and development of social collaboration with stakeholders to meet
current and future needs of the community and environment. The
framework links between different stakeholders internally and
externally using communication and reporting tools. The results show
that SVU integrates social responsibility and sustainability in its
strategic plans. It has policies and actions however fragmented and
lack of appropriate structure and budgeting. The proposed framework
could be valuable for researchers and decision makers of the
Egyptian Universities. The study proposed recommendations and
highlighted building on the results and conducting future research.
Abstract: Acoustic properties of polymeric liquids are high
sensitive to free gas traces in the form of fine bubbles. Their presence
is typical for such liquids because of chemical reactions, small
wettability of solid boundaries, trapping of air in technological
operations, etc. Liquid temperature influences essentially its
rheological properties, which may have an impact on the bubble
pulsations and sound propagation in the system. The target of the
paper is modeling of the liquid temperature effect on single bubble
dynamics and sound dispersion and attenuation in polymeric solution
with spherical gas bubbles. The basic sources of attenuation (heat
exchange between gas in microbubbles and surrounding liquid,
rheological and acoustic losses) are taken into account. It is supposed
that in the studied temperature range the interface mass transfer has a
minor effect on bubble dynamics. The results of the study indicate
that temperature raise yields enhancement of bubble pulsations and
increase in sound attenuation in the near-resonance range and may
have a strong impact on sound dispersion in the liquid-bubble
mixture at frequencies close to the resonance frequency of bubbles.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: This paper presents the design, development and
evaluation of an application prototype developed to support
tuberculosis (TB) patients’ treatment adherence. The system makes
use of graphics and voice reminders as opposed to text messaging to
encourage patients to follow their medication routine. To evaluate the
effect of the prototype applications, participants were given mobile
phones on which the reminder system was installed. Thirty-eight
people, including TB health workers and patients from Zanzibar,
Tanzania, participated in the evaluation exercises. The results
indicate that the participants found the mobile image-based
application is useful to support TB treatment. All participants
understood and interpreted the intended meaning of every image
correctly. The study findings revealed that the use of a mobile visualbased
application may have potential benefit to support TB patients
(both literate and illiterate) in their treatment processes.
Abstract: In light of the technological development and its
introduction into the field of education, an online course was
designed in parallel to the 'conventional' course for teaching the
''Qualitative Research Methods''. This course aimed to characterize
learning-teaching processes in a 'Qualitative Research Methods'
course studied in two different frameworks. Moreover, its objective
was to explore the difference between the culture of a physical
learning environment and that of online learning. The research
monitored four learner groups, a total of 72 students, for two years,
two groups from the two course frameworks each year. The courses
were obligatory for M.Ed. students at an academic college of
education and were given by one female-lecturer. The research was
conducted in the qualitative method as a case study in order to attain
insights about occurrences in the actual contexts and sites in which
they transpire. The research tools were open-ended questionnaire and
reflections in the form of vignettes (meaningful short pictures) to all
students as well as an interview with the lecturer. The tools facilitated
not only triangulation but also collecting data consisting of voices
and pictures of teaching and learning. The most prominent findings
are: differences between the two courses in the change features of the
learning environment culture for the acquisition of contents and
qualitative research tools. They were manifested by teaching
methods, illustration aids, lecturer's profile and students' profile.
Abstract: In this paper a novel color image compression
technique for efficient storage and delivery of data is proposed. The
proposed compression technique started by RGB to YCbCr color
transformation process. Secondly, the canny edge detection method is
used to classify the blocks into the edge and non-edge blocks. Each
color component Y, Cb, and Cr compressed by discrete cosine
transform (DCT) process, quantizing and coding step by step using
adaptive arithmetic coding. Our technique is concerned with the
compression ratio, bits per pixel and peak signal to noise ratio, and
produce better results than JPEG and more recent published schemes
(like CBDCT-CABS and MHC). The provided experimental results
illustrate the proposed technique that is efficient and feasible in terms
of compression ratio, bits per pixel and peak signal to noise ratio.
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: Neural activity in the human brain starts from the
early stages of prenatal development. This activity or signals
generated by the brain are electrical in nature and represent not only
the brain function but also the status of the whole body. At the
present moment, three methods can record functional and
physiological changes within the brain with high temporal resolution
of neuronal interactions at the network level: the
electroencephalogram (EEG), the magnet oencephalogram (MEG),
and functional magnetic resonance imaging (fMRI); each of these has
advantages and shortcomings. EEG recording with a large number of
electrodes is now feasible in clinical practice. Multichannel EEG
recorded from the scalp surface provides very valuable but indirect
information about the source distribution. However, deep electrode
measurements yield more reliable information about the source
locations intracranial recordings and scalp EEG are used with the
source imaging techniques to determine the locations and strengths of
the epileptic activity. As a source localization method, Low
Resolution Electro-Magnetic Tomography (LORETA) is solved for
the realistic geometry based on both forward methods, the Boundary
Element Method (BEM) and the Finite Difference Method (FDM). In
this paper, we review the findings EEG- LORETA about epilepsy.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.