Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: One of the most important problems to solve is eye
location for a driver fatigue monitoring system. This paper presents an
efficient method to achieve fast and accurate eye location in grey level
images obtained in the real-word driving conditions. The structure of
eye region is used as a robust cue to find possible eye pairs. Candidates
of eye pair at different scales are selected by finding regions which
roughly match with the binary eye pair template. To obtain real one,
all the eye pair candidates are then verified by using support vector
machines. Finally, eyes are precisely located by using binary vertical
projection and eye classifier in eye pair images. The proposed method
is robust to deal with illumination changes, moderate rotations, glasses
wearing and different eye states. Experimental results demonstrate its
effectiveness.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: This study presents the application of artificial
neural network for modeling the phenolic compound
migration through vertical soil column. A three layered feed
forward neural network with back propagation training
algorithm was developed using forty eight experimental data
sets obtained from laboratory fixed bed vertical column tests.
The input parameters used in the model were the influent
concentration of phenol(mg/L) on the top end of the soil
column, depth of the soil column (cm), elapsed time after
phenol injection (hr), percentage of clay (%), percentage of
silt (%) in soils. The output of the ANN was the effluent
phenol concentration (mg/L) from the bottom end of the soil
columns. The ANN predicted results were compared with the
experimental results of the laboratory tests and the accuracy of
the ANN model was evaluated.
Abstract: This paper presented the results of an experimental
investigation into the axial fatigue behavior of a 5086 aluminum
alloy which have several notch-aspect ratios a0/c0 and notch
thickness ratio a/t with semi-elliptical surface cracks. Tests were
conducted in la b air for stress levels of 50 % of their yield
strength. Experiments were carried out for various notch to
thickness ratios. Crack growth rates of test specimens both in
surface and depth directions were determined by using die
penetration method. Fuzzy Logic method was used to predict the
deep direction crack growth because the dept of the crack is
considerably difficult to measure.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.
Abstract: In recent years, copulas have become very popular in
financial research and actuarial science as they are more flexible in
modelling the co-movements and relationships of risk factors as compared
to the conventional linear correlation coefficient by Pearson.
However, a precise estimation of the copula parameters is vital in
order to correctly capture the (possibly nonlinear) dependence structure
and joint tail events. In this study, we employ two optimization
heuristics, namely Differential Evolution and Threshold Accepting to
tackle the parameter estimation of multivariate t distribution models
in the EML approach. Since the evolutionary optimizer does not rely
on gradient search, the EML approach can be applied to estimation of
more complicated copula models such as high-dimensional copulas.
Our experimental study shows that the proposed method provides
more robust and more accurate estimates as compared to the IFM
approach.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: This paper presents ageing experiments controlled by the evolution of junction parameters. The deterioration of the device is related to high injection effects which modified the transport mechanisms in the space charge region of the junction. Physical phenomena linked to the degradation of junction parameters that affect the devices reliability are reported and discussed. We have used the method based on numerical analysis of experimental current-voltage characteristic of the junction, in order to extract the electrical parameters. The simultaneous follow-up of the evolutions of the series resistance and of the transition voltage allow us to introduce a new parameter for reliability evaluation.
Abstract: In this paper, a framework for the simplification and
standardization of metaheuristic related parameter-tuning by applying
a four phase methodology, utilizing Design of Experiments and
Artificial Neural Networks, is presented. Metaheuristics are multipurpose
problem solvers that are utilized on computational optimization
problems for which no efficient problem specific algorithm
exist. Their successful application to concrete problems requires the
finding of a good initial parameter setting, which is a tedious and
time consuming task. Recent research reveals the lack of approach
when it comes to this so called parameter-tuning process. In the
majority of publications, researchers do have a weak motivation for
their respective choices, if any. Because initial parameter settings
have a significant impact on the solutions quality, this course of
action could lead to suboptimal experimental results, and thereby
a fraudulent basis for the drawing of conclusions.
Abstract: Data Envelopment Analysis (DEA) is a methodology
that computes efficiency values for decision making units (DMU) in a
given period by comparing the outputs with the inputs. In many cases,
there are some time lag between the consumption of inputs and the
production of outputs. For a long-term research project, it is hard to
avoid the production lead time phenomenon. This time lag effect
should be considered in evaluating the performance of organizations.
This paper suggests a model to calculate efficiency values for the
performance evaluation problem with time lag. In the experimental
part, the proposed methods are compared with the CCR and an
existing time lag model using the data set of the 21st century frontier
R&D program which is a long-term national R&D program of Korea.
Abstract: Different problems may causes distortion of the rotor,
and hence vibration, which is the most severe damage of the turbine
rotors. In many years different techniques have been developed for
the straightening of bent rotors. The method for straightening can be
selected according to initial information from preliminary inspections
and tests such as nondestructive tests, chemical analysis, run out tests
and also a knowledge of the shaft material. This article covers the
various causes of excessive bends and then some applicable common
straightening methods are reviewed. Finally, hot spotting is opted for
a particular bent rotor. A 325 MW steam turbine rotor is modeled and
finite element analyses are arranged to investigate this straightening
process. Results of experimental data show that performing the exact
hot spot straightening process reduced the bending of the rotor
significantly.
Abstract: A structural study of an aqueous electrolyte whose
experimental results are available. It is a solution of LiCl-6H2O type
at glassy state (120K) contrasted with pure water at room temperature
by means of Partial Distribution Functions (PDF) issue from neutron
scattering technique. Based on these partial functions, the Reverse
Monte Carlo method (RMC) computes radial and angular correlation
functions which allow exploring a number of structural features of
the system. The obtained curves include some artifacts. To remedy
this, we propose to introduce a screened potential as an additional
constraint. Obtained results show a good matching between
experimental and computed functions and a significant improvement
in PDFs curves with potential constraint. It suggests an efficient fit of
pair distribution functions curves.
Abstract: Background: Widespread use of chemotherapeutic
drugs in the treatment of cancer has lead to higher health hazards
among employee who handle and administer such drugs, so nurses
should know how to protect themselves, their patients and their work
environment against toxic effects of chemotherapy. Aim of this study
was carried out to examine the effect of chemotherapy safety protocol
for oncology nurses on their protective measure practices. Design: A
quasi experimental research design was utilized. Setting: The study
was carried out in oncology department of Menoufia university
hospital and Tanta oncology treatment center. Sample: A
convenience sample of forty five nurses in Tanta oncology treatment
center and eighteen nurses in Menoufiya oncology department.
Tools: 1. an interviewing questionnaire that covering sociodemographic
data, assessment of unit and nurses' knowledge about
chemotherapy. II: Obeservational check list to assess nurses' actual
practices of handling and adminestration of chemotherapy. A base
line data were assessed before implementing Chemotherapy Safety
protocol, then Chemotherapy Safety protocol was implemented, and
after 2 monthes they were assessed again. Results: reveled that 88.9%
of study group I and 55.6% of study group II improved to good total
knowledge scores after educating on the safety protocol, also 95.6%
of study group I and 88.9% of study group II had good total practice
score after educating on the safety protocol. Moreover less than half
of group I (44.4%) reported that heavy workload is the most barriers
for them, while the majority of group II (94.4%) had many barriers
for adhering to the safety protocol such as they didn’t know the
protocol, the heavy work load and inadequate equipment.
Conclusions: Safety protocol for Oncology Nurses seemed to have
positive effect on improving nurses' knowledge and practice.
Recommendation: chemotherapy safety protocol should be instituted
for all oncology nurses who are working in any oncology unit and/ or
center to enhance compliance, and this protocol should be done at
frequent intervals.
Abstract: The principle of frequency and amplitude measurement of a vibrating object in water using ultrasonic speckle technique is presented in this paper. Compared with other traditional techniques, the ultrasonic speckle technique can be applied to vibration measurement of a nonmetal object with rough surface in water in a noncontact way. The relationship between speckle movement and object movement was analyzed. Based on this study, an ultrasonic speckle measurement system was set up. With this system the frequency and amplitude of an underwater vibrating cantilever beam was detected. The result shows that the experimental data is in good agreement with the calibrating data.
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.
Abstract: In this paper, a methodology of a model based on
predicting the tool forces oblique machining are introduced by
adopting the orthogonal technique. The applied analytical calculation
is mostly based on Devries model and some parts of the methodology
are employed from Amareggo-Brown model. Model validation is
performed by comparing experimental data with the prediction results
on machining titanium alloy (Ti-6Al-4V) based on micro-cutting tool
perspective. Good agreements with the experiments are observed. A
detailed friction form that affected the tool forces also been examined
with reasonable results obtained.