Abstract: Sentiment analysis (SA) has received growing
attention in Arabic language research. However, few studies have yet
to directly apply SA to Arabic due to lack of a publicly available
dataset for this language. This paper partially bridges this gap due to
its focus on one of the Arabic dialects which is the Saudi dialect. This
paper presents annotated data set of 4700 for Saudi dialect sentiment
analysis with (K= 0.807). Our next work is to extend this corpus and
creation a large-scale lexicon for Saudi dialect from the corpus.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.
Abstract: In this paper, we present the design of the
super-ellipsoidal potential function (SEPF), that can be used for
autonomous collision avoidance of an unmanned aerial vehicle (UAV)
in a 3-dimensional space. In the design of SEPF, we have the
full control over the shape and size of the potential function. In
particular, we can adjust the length, width, height, and the amount
of flattening at the tips of the potential function so that the collision
avoidance motion vector generated from the potential function can
be adjusted accordingly. Based on the idea of the SEPF, we also
propose an approach for the local autonomy of a UAV for its collision
avoidance when the UAV is teleoperated by a human operator. In
our proposed approach, a teleoperated UAV can not only avoid
collision autonomously with other surrounding objects but also track
the operator’s control input as closely as possible. As a result, an
operator can always be in control of the UAV for his/her high-level
guidance and navigation task without worrying too much about
the UAVs collision avoidance while it is being teleoperated. The
effectiveness of the proposed approach is demonstrated through a
human-in-the-loop simulation of quadrotor UAV teleoperation using
virtual robot experimentation platform (v-rep) and Matlab programs.
Abstract: Reinforced earth structures are generally subjected to cyclic loading generated from earthquakes. This paper presents a summary of the results and analyses of a testing program carried out in a large-scale multi-function geosynthetic testing apparatus that accommodates soil samples up to 1.0 m3. This apparatus performs different shear and pullout tests under both static and cyclic loading. The testing program was carried out to investigate the controlling factors affecting soil/geogrid interaction under cyclic loading. The extensibility of the geogrids, the applied normal stresses, the characteristics of the cyclic loading (frequency, and amplitude), and initial static load within the geogrid sheet were considered in the testing program. Based on the findings of the testing program, the effect of these parameters on the pullout resistance of geogrids, as well as the displacement mobility under cyclic loading were evaluated. Conclusions and recommendations for the design of reinforced earth walls under cyclic loading are presented.
Abstract: The power buck converter is the most widely used
DC/DC converter topology. They have a very large application area
such as DC motor drives, photovoltaic power system which require
fast transient responses and high efficiency over a wide range of load
current. This work proposes, the modelling of DC/DC power buck
converter using state-space averaging method and the current-mode
control using a proportional-integral controller. The efficiency of the
proposed model and control loop are evaluated with operating point
changes. The simulation results proved the effectiveness of the linear
model of DC/DC power buck converter.
Abstract: Cloud computing is a business model which provides
an easier management of computing resources. Cloud users can
request virtual machine and install additional softwares and configure
them if needed. However, user can also request virtual appliance
which provides a better solution to deploy application in much faster
time, as it is ready-built image of operating system with necessary
softwares installed and configured. Large numbers of virtual
appliances are available in different image format. User can
download available appliances from public marketplace and start
using it. However, information published about the virtual appliance
differs from each providers leading to the difficulty in choosing
required virtual appliance as it is composed of specific OS with
standard software version. However, even if user choses the
appliance from respective providers, user doesn’t have any flexibility
to choose their own set of softwares with required OS and
application. In this paper, we propose a referenced architecture for
dynamically customizing virtual appliance and provision them in an
easier manner. We also add our experience in integrating our
proposed architecture with public marketplace and Mi-Cloud, a cloud
management software.
Abstract: The combination of multi–walled carbon nanotubes
(MWCNTs) with polymers offers an attractive route to reinforce the
macromolecular compounds as well as the introduction of new
properties based on morphological modifications or electronic
interactions between the two constituents. As they are only a few
nanometers in dimension, it offers ultra-large interfacial area per
volume between the nano-element and polymer matrix. Nevertheless,
the use of MWCNTs as a rough material in different applications has
been largely limited by their poor processability, insolubility, and
infusibility. Studies concerning the nanofiller reinforced polymer
composites are justified in an attempt to overcome these limitations.
This work presents one preliminary study of MWCNTs dispersion
into the PVDF homopolymer. For preparation, the composite
components were diluted in n,n-dimethylacetamide (DMAc) with
mechanical agitation assistance. After complete dilution, followed by
slow evaporation of the solvent at 60°C, the samples were dried.
Films of about 80 μm were obtained. FTIR and UV-Vis
spectroscopic techniques were used to characterize the
nanocomposites. The appearance of absorption bands in the FTIR
spectra of nanofilled samples, when compared to the spectrum of
pristine PVDF samples, are discussed and compared with the UV-Vis
measurements.
Abstract: The aim of this paper is to develop an empirical
research on the nature and consequences of corporate governance on
Eurozone Insurance Industry risk taking attitude. More particularly,
we analyzed the effect of public ownership on risk taking with
respect to privately held Insurance Companies. We also analyzed the
effects on risk taking attitude of different degrees of ownership
concentration, directors compensation, and the dimension/diversity of
the Board of Directors. Our results provide quite strong evidence that,
coherently with the Agency Theory, publicly traded insurance
companies with more concentrated ownership are less risky than the
corresponding privately held.
Abstract: Large scale Indian manufacturers started
implementing Six Sigma to their supply core to fulfill the endless
need of high quality products. As well, they initiated encouraging
their suppliers to apply the well-ascertain SS management practice
and kept no resource for supplier enterprises, generally small midsized
enterprises to think for the admittance of Six Sigma as a quality
promotion drive. There are many issues to study for requisite changes
before the introduction of Six Sigma in auto SMEs. This paper
converges on impeding factors while implementing SS drive and also
pinpoints the gains achieved through successful implementation. The
result of this study suggest some operational guidelines for effective
implementation of Six Sigma from evidences acquired through
research questionnaire and interviews with industrial professionals,
apportioned to assort auto sector mid-sized enterprises (MSEs) in
India.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: Green chemistry for plant extraction of active principles is the main interest of many researchers concerned with climate change. While classical organic solvents are detrimental to our environment, greener alternatives to ionic liquids are very promising for sustainable organic chemistry. This study focused on the determination of functional groups observed in the main constituents from the ionic liquid extracts of Coleus aromaticus Benth leaves using FT-IR Spectroscopy. Moreover, this research aimed to determine the best ionic liquid that can separate functionalized plant constituents from the leaves Coleus aromaticus Benth using Fourier Transform Infrared Spectroscopy. Coleus aromaticus Benth leaf extract in different ionic liquids, elucidated pharmacologically important functional groups present in major constituents of the plant, namely, rosmarinic acid, caffeic acid and chlorogenic acid. In connection to distinctive appearance of functional groups in the spectrum and highest % transmittance, potassium chloride-glycerol is the best ionic liquid for green extraction.
Abstract: High double excitation of two-electron atoms has been
investigated using hyperpherical coordinates within a modified
adiabatic expansion technique. This modification creates a novel
fictitious force leading to a spontaneous exchange symmetry breaking
at high double excitation. The Pauli principle must therefore be
regarded as approximation valid only at low excitation energy.
Threshold electron scattering from high Rydberg states shows an
unexpected time reversal symmetry breaking. At threshold for double
escape we discover a broad (few eV) Cooper pair.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.
Abstract: Dan C. Lortie’s Schoolteacher: A sociological study is
one of the best works on the sociology of teaching since W. Waller’s
classic study. It is a book worthy of review. Following the tradition of
symbolic interactionists, Lortie demonstrated the qualities who studied
the occupation of teaching. Using several methods to gather effective
data, Lortie has portrayed the ethos of the teaching profession.
Therefore, the work is an important book on the teaching profession
and teacher culture. Though outstanding, Lortie’s work is also flawed
in that his perspectives and methodology were adopted largely from
symbolic interactionism. First, Lortie in his work analyzed many
points regarding teacher culture; for example, he was interested in
exploring “sentiment,” “cathexis,” and “ethos.” Thus, he was more a
psychologist than a sociologist. Second, symbolic interactionism led
him to discern the teacher culture from a micro view, thereby missing
the structural aspects. For example, he did not fully discuss the issue of
gender and he ignored the issue of race. Finally, following the
qualitative sociological tradition, Lortie employed many qualitative
methods to gather data but only foucused on obtaining and presenting
interview data. Moreover, he used measurement methods that were too
simplistic for analyzing quantitative data fully.
Abstract: The Hall Coefficient (HC) and the Magnetoresistance (MR) have been studied in two-dimensional systems. The HC and the MR in Rectangular Quantum Wire (RQW) subjected to a crossed DC electric field and magnetic field in the presence of a Strong Electromagnetic Wave (EMW) characterized by electric field are studied in this work. Using the quantum kinetic equation for electrons interacting with optical phonons, we obtain the analytic expressions for the HC and the MR with a dependence on magnetic field, EMW frequency, temperatures of systems and the length characteristic parameters of RQW. These expressions are different from those obtained for bulk semiconductors and cylindrical quantum wires. The analytical results are applied to GaAs/GaAs/Al. For this material, MR depends on the ratio of the EMW frequency to the cyclotron frequency. Indeed, MR reaches a minimum at the ratio 5/4, and when this ratio increases, it tends towards a saturation value. The HC can take negative or positive values. Each curve has one maximum and one minimum. When magnetic field increases, the HC is negative, achieves a minimum value and then increases suddenly to a maximum with a positive value. This phenomenon differs from the one observed in cylindrical quantum wire, which does not have maximum and minimum values.