Abstract: This paper is concerned with an epidemic model with delay. By using the comparison theorem of the differential equation and constructing a suitable Lyapunov functional, Some sufficient conditions which guarantee the permeance and existence of a unique globally attractive positive almost periodic solution of the model are obtain. Finally, an example is employed to illustrate our result.
Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Abstract: A novel low-cost impedance control structure is
proposed for monitoring the contact force between end-effector and
environment without installing an expensive force/torque sensor.
Theoretically, the end-effector contact force can be estimated from the
superposition of each joint control torque. There have a nonlinear
matrix mapping function between each joint motor control input and
end-effector actuating force/torques vector. This new force control
structure can be implemented based on this estimated mapping matrix.
First, the robot end-effector is manipulated to specified positions, then
the force controller is actuated based on the hall sensor current
feedback of each joint motor. The model-free fuzzy sliding mode
control (FSMC) strategy is employed to design the position and force
controllers, respectively. All the hardware circuits and software
control programs are designed on an Altera Nios II embedded
development kit to constitute an embedded system structure for a
retrofitted Mitsubishi 5 DOF robot. Experimental results show that PI
and FSMC force control algorithms can achieve reasonable contact
force monitoring objective based on this hardware control structure.
Abstract: When it comes to last, it is regarded as the critical
foundation of shoe design and development. A computer aided
methodology for various last form designs is proposed in this study.
The reverse engineering is mainly applied to the process of scanning
for the last form. Then with the minimum energy for revision of
surface continuity, the surface reconstruction of last is rebuilt by the
feature curves of the scanned last. When the surface reconstruction of
last is completed, the weighted arithmetic mean method is applied to
the computation on the shape morphing for the control mesh of last,
thus 3D last form of different sizes is generated from its original form
feature with functions remained. In the end, the result of this study is
applied to an application for 3D last reconstruction system. The
practicability of the proposed methodology is verified through later
case studies.
Abstract: This paper presents a novel method for remaining
useful life prediction using the Elliptical Basis Function (EBF)
network and a Markov chain. The EBF structure is trained by a
modified Expectation-Maximization (EM) algorithm in order to take
into account the missing covariate set. No explicit extrapolation is
needed for internal covariates while a Markov chain is constructed to
represent the evolution of external covariates in the study. The
estimated external and the unknown internal covariates constitute an
incomplete covariate set which are then used and analyzed by the EBF
network to provide survival information of the asset. It is shown in the
case study that the method slightly underestimates the remaining
useful life of an asset which is a desirable result for early maintenance
decision and resource planning.
Abstract: A Negotiation Support is required on a value-based decision to enable each stakeholder to evaluate and rank the solution alternatives before engaging into negotiation with the other stakeholders. This study demonstrates a process of negotiation support model for selection of a building system from value-based design perspective. The perspective is based on comparison of function and cost of a building system. Multi criteria decision techniques were applied to determine the relative value of the alternative solutions for performing the function. A satisfying option game theory are applied to the criteria of value-based decision which are LCC (life cycle cost) and function based FAST. The results demonstrate a negotiation process to select priorities of a building system. The support model can be extended to an automated negotiation by combining value based decision method, group decision and negotiation support.
Abstract: Because of the low maintenance and robustness induction motors have many applications in the industries. The speed control of induction motor is more important to achieve maximum torque and efficiency. Various speed control techniques like, Direct Torque Control, Sensorless Vector Control and Field Oriented Control are discussed in this paper. Soft computing technique – Fuzzy logic is applied in this paper for the speed control of induction motor to achieve maximum torque with minimum loss. The fuzzy logic controller is implemented using the Field Oriented Control technique as it provides better control of motor torque with high dynamic performance. The motor model is designed and membership functions are chosen according to the parameters of the motor model. The simulated design is tested using various tool boxes in MATLAB. The result concludes that the efficiency and reliability of the proposed speed controller is good.
Abstract: Cardiovascular diseases, principally atherosclerosis, are responsible for 30% of world deaths. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis.It is increasingly recognized that the initiation and progression of disease and the occurrence of clinical events is a complex interplay between the local biomechanical environment and the local vascular biology. The aim of this study is to investigate the flow behavior through a stenosed artery. A physical experiment was performed using an artery model and blood analogue fluid. An axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. The flow field was measured using particle image velocimetry (PIV). Spherical particles with 20μm diameter were seeded in a water-glycerol-NaCl mixture. Steady flow Reynolds numbers are 250. The area of interest is the region after the stenosis where the flow separation occurs. The velocity field was measured and the velocity gradient was investigated. There was high particle concentration in the recirculation zone. High velocity gradient formed immediately after the stenosis throat created a lift force that enhanced particle migration to the flow separation area.
Abstract: Static analysis of source code is used for auditing web
applications to detect the vulnerabilities. In this paper, we propose a
new algorithm to analyze the PHP source code for detecting LFI and
RFI potential vulnerabilities. In our approach, we first define some
patterns for finding some functions which have potential to be abused
because of unhandled user inputs. More precisely, we use regular
expression as a fast and simple method to define some patterns for
detection of vulnerabilities. As inclusion functions could be also used
in a safe way, there could occur many false positives (FP). The first
cause of these FP-s could be that the function does not use a usersupplied
variable as an argument. So, we extract a list of usersupplied
variables to be used for detecting vulnerable lines of code.
On the other side, as vulnerability could spread among the variables
like by multi-level assignment, we also try to extract the hidden usersupplied
variables. We use the resulted list to decrease the false
positives of our method. Finally, as there exist some ways to prevent
the vulnerability of inclusion functions, we define also some patterns
to detect them and decrease our false positives.
Abstract: Tool wear and surface roughness prediction plays a
significant role in machining industry for proper planning and control
of machining parameters and optimization of cutting conditions. This
paper deals with developing an artificial neural network (ANN)
model as a function of cutting parameters in turning steel under
minimum quantity lubrication (MQL). A feed-forward
backpropagation network with twenty five hidden neurons has been
selected as the optimum network. The co-efficient of determination
(R2) between model predictions and experimental values are 0.9915,
0.9906, 0.9761 and 0.9627 in terms of VB, VM, VS and Ra
respectively. The results imply that the model can be used easily to
forecast tool wear and surface roughness in response to cutting
parameters.
Abstract: In this paper, a neural network tuned fuzzy controller
is proposed for controlling Multi-Input Multi-Output (MIMO)
systems. For the convenience of analysis, the structure of MIMO
fuzzy controller is divided into single input single-output (SISO)
controllers for controlling each degree of freedom. Secondly,
according to the characteristics of the system-s dynamics coupling, an
appropriate coupling fuzzy controller is incorporated to improve the
performance. The simulation analysis on a two-level mass–spring
MIMO vibration system is carried out and results show the
effectiveness of the proposed fuzzy controller. The performance
though improved, the computational time and memory used is
comparatively higher, because it has four fuzzy reasoning blocks and
number may increase in case of other MIMO system. Then a fuzzy
neural network is designed from a set of input-output training data to
reduce the computing burden during implementation. This control
strategy can not only simplify the implementation problem of fuzzy
control, but also reduce computational time and consume less
memory.
Abstract: In the closed quantum system, if the control system is
strongly regular and all other eigenstates are directly coupled to the
target state, the control system can be asymptotically stabilized at the
target eigenstate by the Lyapunov control based on the state error.
However, if the control system is not strongly regular or as long as
there is one eigenstate not directly coupled to the target state, the
situations will become complicated. In this paper, we propose an
implicit Lyapunov control method based on the state error to solve the
convergence problems for these two degenerate cases. And at the same
time, we expand the target state from the eigenstate to the arbitrary
pure state. Especially, the proposed method is also applicable in the
control system with multi-control Hamiltonians. On this basis, the
convergence of the control systems is analyzed using the LaSalle
invariance principle. Furthermore, the relation between the implicit
Lyapunov functions of the state distance and the state error is
investigated. Finally, numerical simulations are carried out to verify
the effectiveness of the proposed implicit Lyapunov control method.
The comparisons of the control effect using the implicit Lyapunov
control method based on the state distance with that of the state error
are given.
Abstract: A stiffened laminated composite panel (1 m length ×
0.5m width) was optimized for minimum weight and deflection under
several constraints using genetic algorithm. Here, a significant study
on the performance of a penalty function with two kinds of static and
dynamic penalty factors was conducted. The results have shown that
linear dynamic penalty factors are more effective than the static ones.
Also, a specially combined linear-exponential function has shown to
perform more effective than the previously mentioned penalty
functions. This was then resulted in the less sensitivity of the GA to
the amount of penalty factor.
Abstract: A new nonlinear PID controller and its stability
analysis are presented in this paper. A nonlinear function is deduced
from the similarities between the control effort and the electric-field
effect of a capacitor. The conventional linear PID controller can be
modified into a nonlinear one by this function. To analyze the stability
of the nonlinear PID controlled system, an idea of energy equivalence
is adapted to avoid the conservativeness which is usually arisen from
some traditional theorems and Criterions. The energy equivalence is
naturally related with the conceptions of Passivity and T-Passivity. As
a result, an engineering guideline for the parameter design of the
nonlinear PID controller is obtained. An inverted pendulum system is
tested to verify the nonlinear PID control scheme.
Abstract: Controlled modification of appropriate sharpness for
nanotips is of paramount importance to develop novel materials and
functional devices at a nanometer resolution. Herein, we present a
reliable and unique strategy of laser irradiation enhanced
physicochemical etching to manufacture super sharp tungsten tips
with reproducible shape and dimension as well as high yields
(~80%). The corresponding morphology structure evolution of
tungsten tips and laser-tip interaction mechanisms were
systematically investigated and discussed using field emission
scanning electron microscope (SEM) and physical optics statistics
method with different fluences under 532 nm laser irradiation. This
work paves the way for exploring more accessible metallic tips
applications with tunable apex diameter and aspect ratio, and,
furthermore, facilitates the potential sharpening enhancement
technique for other materials used in a variety of nanoscale devices.
Abstract: A lot of Scientific and Engineering problems require the solution of large systems of linear equations of the form bAx in an effective manner. LU-Decomposition offers good choices for solving this problem. Our approach is to find the lower bound of processing elements needed for this purpose. Here is used the so called Omega calculus, as a computational method for solving problems via their corresponding Diophantine relation. From the corresponding algorithm is formed a system of linear diophantine equalities using the domain of computation which is given by the set of lattice points inside the polyhedron. Then is run the Mathematica program DiophantineGF.m. This program calculates the generating function from which is possible to find the number of solutions to the system of Diophantine equalities, which in fact gives the lower bound for the number of processors needed for the corresponding algorithm. There is given a mathematical explanation of the problem as well. Keywordsgenerating function, lattice points in polyhedron, lower bound of processor elements, system of Diophantine equationsand : calculus.
Abstract: A new chelating resin is prepared by coupling
Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer.
The resulting sorbent has been characterized by FT-IR, elemental
analysis and thermogravimetric analysis (TGA) and studied for
preconcentrating of Cu (II) using flame atomic absorption
spectrometry (FAAS) for metal monitoring. The optimum pH value
for sorption of the copper ions was 6.5. The resin was subjected to
evaluation through batch binding of mentioned metal ion.
Quantitative desorption occurs instantaneously with 0.5 M HNO3.
The sorption capacity was found 4.8 mmol.g-1 of resin for Cu (II) in
the aqueous solution. The chelating resin can be reused for 10 cycles
of sorption-desorption without any significant change in sorption
capacity. A recovery of 99% was obtained the metal ions with 0.5 M
HNO3 as eluting agent. The method was applied for metal ions
determination from industrial waste water sample.
Abstract: This paper deals with the synthesis of fuzzy controller
applied to a permanent magnet synchronous machine (PMSM) with a
guaranteed H∞ performance. To design this fuzzy controller,
nonlinear model of the PMSM is approximated by Takagi-Sugeno
fuzzy model (T-S fuzzy model), then the so-called parallel
distributed compensation (PDC) is employed. Next, we derive the
property of the H∞ norm. The latter is cast in terms of linear matrix
inequalities (LMI-s) while minimizing the H∞ norm of the transfer
function between the disturbance and the error ( ) ev T . The
experimental and simulations results were conducted on a permanent
magnet synchronous machine to illustrate the effects of the fuzzy
modelling and the controller design via the PDC.
Abstract: This paper suggests ranking alternatives under fuzzy
MCDM (multiple criteria decision making) via an centroid based
ranking approach, where criteria are classified to benefit qualitative,
benefit quantitative and cost quantitative ones. The ratings of
alternatives versus qualitative criteria and the importance weights of
all criteria are assessed in linguistic values represented by fuzzy
numbers. The membership function for the final fuzzy evaluation
value of each alternative can be developed through α-cuts and
interval arithmetic of fuzzy numbers. The distance between the
original point and the relative centroid is applied to defuzzify the
final fuzzy evaluation values in order to rank alternatives. Finally a
numerical example demonstrates the computation procedure of the
proposed model.
Abstract: A 3D simulation study for an incompressible
slip flow around a spherical aerosol particle was performed.
The full Navier-Stokes equations were solved and the velocity
jump at the gas-particle interface was treated numerically by
imposition of the slip boundary condition. Analytical solution
to the Stokesian slip flow past a spherical particle was used as
a benchmark for code verification, and excellent agreement
was achieved. The Simulation results showed that in addition
to the Knudsen number, the Reynolds number affects the slip
correction factor. Thus, the Cunningham-based slip corrections
must be augmented by the inclusion of the effect of
Reynolds number for application to Lagrangian tracking of
fine particles. A new expression for the slip correction factor
as a function of both Knudsen number and Reynolds number
was developed.