Abstract: Polypropylene blended with natural oil and pigment additives has been studied. Different formulations for each compound were made into polybag used for cultivation of oil palm seedlings for strength and mechanical properties studies. One group of sample was exposed under normal sunlight to initiate degradation and another group of sample was placed under shaded area for five months. All samples were tested for tensile strength to determine the degradation effects. The tensile strength of directly exposed sunlight samples and shaded area showed up to 50% and 25% degradation respectively. However, similar reduction of Young’s modulus for all samples was found for both exposures. Structural investigations were done using FTIR to detect deformation. The natural additives that were used in the studies were all natural and environmental friendly
Abstract: This paper presents a sensor-based motion planning algorithm for 3-DOF car-like robots with a nonholonomic constraint. Similar to the classic Bug family algorithms, the proposed algorithm enables the car-like robot to navigate in a completely unknown environment using only the range sensor information. The car-like robot uses the local range sensor view to determine the local path so that it moves towards the goal. To guarantee that the robot can approach the goal, the two modes of motion are repeated, termed motion-to-goal and wall-following. The motion-to-goal behavior lets the robot directly move toward the goal, and the wall-following behavior makes the robot circumnavigate the obstacle boundary until it meets the leaving condition. For each behavior, the nonholonomic motion for the car-like robot is planned in terms of the instantaneous turning radius. The proposed algorithm is implemented to the real robot and the experimental results show the performance of proposed algorithm.
Abstract: The ability of agricultural and decorative plants to
absorb and detoxify TNT and RDX has been studied. All tested 8
plants, grown hydroponically, were able to absorb these explosives
from water solutions: Alfalfa > Soybean > Chickpea> Chikling vetch
>Ryegrass > Mung bean> China bean > Maize. Differently from
TNT, RDX did not exhibit negative influence on seed germination
and plant growth. Moreover, some plants, exposed to RDX
containing solution were increased in their biomass by 20%. Study of
the fate of absorbed [1-14ðí]-TNT revealed the label distribution in
low and high-molecular mass compounds, both in roots and above
ground parts of plants, prevailing in the later. Content of 14ðí in lowmolecular
compounds in plant roots are much higher than in above
ground parts. On the contrary, high-molecular compounds are more
intensively labeled in aboveground parts of soybean. Most part (up to
70%) of metabolites of TNT, formed either by enzymatic reduction
or oxidation, is found in high molecular insoluble conjugates.
Activation of enzymes, responsible for reduction, oxidation and
conjugation of TNT, such as nitroreductase, peroxidase,
phenoloxidase and glutathione S-transferase has been demonstrated.
Among these enzymes, only nitroreductase was shown to be induced
in alfalfa, exposed to RDX. The increase in malate dehydrogenase
activities in plants, exposed to both explosives, indicates
intensification of Tricarboxylic Acid Cycle, that generates reduced
equivalents of NAD(P)H, necessary for functioning of the
nitroreductase. The hypothetic scheme of TNT metabolism in plants
is proposed.
Abstract: This study aims to investigate empirically the valuerelevance
of accounting information to domestic investors in Tehran
stock exchange from 1999 to 2006. During the present research
impacts of two factors, including positive vs. negative earnings and
the firm size are considered as well. The authors used earnings per
share and annual change of earnings per share as the income
statement indices, and book value of equity per share as the balance
sheet index. Return and Price models through regression analysis are
deployed in order to test the research hypothesis. Results depicted
that accounting information is value-relevance to domestic investors
in Tehran Stock Exchange according to both studied models.
However, income statement information has more value-relevance
than the balance sheet information. Furthermore, positive vs. negative
earnings and firm size seems to have significant impact on valuerelevance
of accounting information.
Abstract: A serious problem on the WWW is finding reliable
information. Not everything found on the Web is true and the
Semantic Web does not change that in any way. The problem will be
even more crucial for the Semantic Web, where agents will be
integrating and using information from multiple sources. Thus, if an
incorrect premise is used due to a single faulty source, then any
conclusions drawn may be in error. Thus, statements published on
the Semantic Web have to be seen as claims rather than as facts, and
there should be a way to decide which among many possibly
inconsistent sources is most reliable. In this work, we propose a trust
model for the Semantic Web. The proposed model is inspired by the
use trust in human society. Trust is a type of social knowledge and
encodes evaluations about which agents can be taken as reliable
sources of information or services. Our proposed model allows
agents to decide which among different sources of information to
trust and thus act rationally on the semantic web.
Abstract: Calcite aCalcite and aragonite are the two common
polymorphs of CaCO3 observed as biominerals. It is universal that
the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM).
In vivo crystallization, Mg2+ inhibits calcite formation. For this
reason, stony corals skeleton may be formed only aragonite crystals
in the biocalcification. It is special in case of soft corals of which
formed only calcite crystal; however, this interesting phenomenon,
still uncharacterized in the marine environment, has been explored in
this study using newly purified cell-free proteins isolated from the
endoskeletal sclerites of soft coral. By recording the decline of pH in
vitro, the control of CaCO3 nucleation and crystal growth by the cellfree
proteins was revealed. Using Atomic Force Microscope, here we
find that these endoskeletal cell-free proteins significantly design the
morphological shape in the molecular-scale kinetics of crystal
formation and those proteins act as surfactants to promote ion
attachment at calcite steps.nd aragonite are the two common polymorphs of CaCO3 observed as biominerals. It is universal that the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM). In vivo crystallization, Mg2+ inhibits calcite formation. For this reason, stony corals skeleton may be formed only aragonite crystals in the biocalcification. It is special in case of soft corals of which formed only calcite crystal; however, this interesting phenomenon, still uncharacterized in the marine environment, has been explored in this study using newly purified cell-free proteins isolated from the endoskeletal sclerites of soft coral. By recording the decline of pH in vitro, the control of CaCO3 nucleation and crystal growth by the cell-free proteins was revealed. Using Atomic Force Microscope, here we find that these endoskeletal cell-free proteins significantly design the morphological shape in the molecular-scale kinetics of crystal formation and those proteins act as surfactants to promote ion attachment at calcite steps. KeywordsBiomineralization, Calcite, Cell-free protein, Soft coral
Abstract: Machine Translation (MT) between the Thai and English languages has been a challenging research topic in natural language processing. Most research has been done on English to Thai machine translation, but not the other way around. This paper presents a Thai to English Machine Translation System that translates a Thai sentence into interlingua of a Thai LFG tree using LFG grammar and a bottom up parser. The Thai LFG tree is then transformed into the corresponding English LFG tree by pattern matching and node transformation. Finally, an equivalent English sentence is created using structural information prescribed by the English LFG tree. Based on results of experiments designed to evaluate the performance of the proposed system, it can be stated that the system has been proven to be effective in providing a useful translation from Thai to English.
Abstract: the present paper, using the technique of differential subordination, we obtain certain results for analytic functions defined by a multiplier transformation in the open unit disc E = { z : IzI < 1}. We claim that our results extend and generalize the existing results in this particular direction
Abstract: Excessive ductility demand on shorter piers is a
common problem for irregular bridges subjected to strong ground
motion. Various techniques have been developed to reduce the
likelihood of collapse of bridge due to failure of shorter piers. This
paper presents the new approach to improve the seismic behavior of
such bridges using Nitinol shape memory alloys (SMAs).
Superelastic SMAs have the ability to remain elastic under very large
deformation due to martensitic transformation. This unique property
leads to enhanced performance of controlled bridge compared with
the performance of the reference bridge. To evaluate the effectiveness
of the devices, nonlinear time history analysis is performed on a RC
single column bent highway bridge using a suite of representative
ground motions. The results show that this method is very effective in
limiting the ductility demand of shorter pier.
Abstract: Obstructive sleep apnea in patients, between 70 and 80
percent, can be cured with just a posture correcting. The most import
thing to do this is detection of obstructive sleep apnea. Detection of
obstructive sleep apnea can be performed through heart rate variability
analysis using power spectrum density analysis. After HRV analysis
we needed to know the current position information for correcting the
position. The pressure sensors of the array type were used to obtain
position information. These sensors can obtain information from the
experimenter about position. In addition, air cylinder corrected the
position of the experimenter by lifting the bed. The experimenter can
be changed position without breaking during sleep by the system.
Polysomnograph recording were obtained from 10 patients. The
results of HRV analysis were that NLF and LF/HF ratio increased,
while NHF decreased during OSA. Position change had to be done the
periods.
Abstract: Patients with diabetes are susceptible to chronic foot
wounds which may be difficult to manage and slow to heal.
Diagnosis and treatment currently rely on the subjective judgement of
experienced professionals. An objective method of tissue assessment
is required. In this paper, a data fusion approach was taken to wound
tissue classification. The supervised Maximum Likelihood and
unsupervised Multi-Modal Expectation Maximisation algorithms
were used to classify tissues within simulated wound models by
weighting the contributions of both colour and 3D depth information.
It was found that, at low weightings, depth information could show
significant improvements in classification accuracy when compared
to classification by colour alone, particularly when using the
maximum likelihood method. However, larger weightings were
found to have an entirely negative effect on accuracy.
Abstract: AAM has been successfully applied to face alignment,
but its performance is very sensitive to initial values. In case the initial
values are a little far distant from the global optimum values, there
exists a pretty good possibility that AAM-based face alignment may
converge to a local minimum. In this paper, we propose a progressive
AAM-based face alignment algorithm which first finds the feature
parameter vector fitting the inner facial feature points of the face and
later localize the feature points of the whole face using the first
information. The proposed progressive AAM-based face alignment
algorithm utilizes the fact that the feature points of the inner part of the
face are less variant and less affected by the background surrounding
the face than those of the outer part (like the chin contour). The
proposed algorithm consists of two stages: modeling and relation
derivation stage and fitting stage. Modeling and relation derivation
stage first needs to construct two AAM models: the inner face AAM
model and the whole face AAM model and then derive relation matrix
between the inner face AAM parameter vector and the whole face
AAM model parameter vector. In the fitting stage, the proposed
algorithm aligns face progressively through two phases. In the first
phase, the proposed algorithm will find the feature parameter vector
fitting the inner facial AAM model into a new input face image, and
then in the second phase it localizes the whole facial feature points of
the new input face image based on the whole face AAM model using
the initial parameter vector estimated from using the inner feature
parameter vector obtained in the first phase and the relation matrix
obtained in the first stage. Through experiments, it is verified that the
proposed progressive AAM-based face alignment algorithm is more
robust with respect to pose, illumination, and face background than the
conventional basic AAM-based face alignment algorithm.
Abstract: This paper aimed to study the factors that relate to
working behavior of employees at Pakkred Municipality, Nonthaburi
Province. A questionnaire was utilized as the tool in collecting
information. Descriptive statistics included frequency, percentage,
mean and standard deviation. Independent- sample t- test, analysis of
variance and Pearson Correlation were also used. The findings of this
research revealed that the majority of the respondents were female,
between 25- 35 years old, married, with a Bachelor degree. The
average monthly salary of respondents was between 8,001- 12,000
Baht, and having about 4-7 years of working experience. Regarding
the overall working motivation factors, the findings showed that
interrelationship, respect, and acceptance were ranked as highly
important factors, whereas motivation, remunerations & welfare,
career growth, and working conditions were ranked as moderately
important factors. Also, overall working behavior was ranked as high.
The hypotheses testing revealed that different genders had a
different working behavior and had a different way of working as a
team, which was significant at the 0.05 confidence level, Moreover,
there was a difference among employees with different monthly
salary in working behavior, problem- solving and decision making,
which all were significant at the 0.05 confidence level. Employees
with different years of working experience were found to have work
working behavior both individual and as a team at the statistical
significance level of 0.01 and 0.05. The result of testing the
relationship between motivation in overall working revealed that
interrelationship, respect and acceptance from others, career growth,
and working conditions related to working behavior at a moderate
level, while motivation in performing duties and remunerations and
welfares related to working behavior towards the same direction at a
low level, with a statistical significance of 0.01.
Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: When the failure function is monotone, some monotonic reliability methods are used to gratefully simplify and facilitate the reliability computations. However, these methods often work in a transformed iso-probabilistic space. To this end, a monotonic simulator or transformation is needed in order that the transformed failure function is still monotone. This note proves at first that the output distribution of failure function is invariant under the transformation. And then it presents some conditions under which the transformed function is still monotone in the newly obtained space. These concern the copulas and the dependence concepts. In many engineering applications, the Gaussian copulas are often used to approximate the real word copulas while the available information on the random variables is limited to the set of marginal distributions and the covariances. So this note catches an importance on the conditional monotonicity of the often used transformation from an independent random vector into a dependent random vector with Gaussian copulas.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: The objective of this study is to propose a statistical
modeling method which enables simultaneous term structure
estimation of the risk-free interest rate, hazard and loss given default,
incorporating the characteristics of the bond issuing company such as
credit rating and financial information. A reduced form model is used
for this purpose. Statistical techniques such as spline estimation and
Bayesian information criterion are employed for parameter estimation
and model selection. An empirical analysis is conducted using the
information on the Japanese bond market data. Results of the
empirical analysis confirm the usefulness of the proposed method.
Abstract: Does a communication modality matter in delivering e-learning information? With the recent growth of broadcasting systems, media technologies and e-learning contents, various systems with different communication modalities have been introduced. In accordance with these trends, this study examines the effects of the information delivery modality on psychology of students. Findings from an experiment indicated that the delivering information which includes a video modality elicited higher degrees of credibility, quality, representativeness of content, and perceived suitability for delivering information than those of auditory information. However, there is no difference between content liking and attitude. The Implications of the findings and the limitations are discussed.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: Combined therapy using Interferon and Ribavirin is the standard treatment in patients with chronic hepatitis C. However, the number of responders to this treatment is low, whereas its cost and side effects are high. Therefore, there is a clear need to predict patient’s response to the treatment based on clinical information to protect the patients from the bad drawbacks, Intolerable side effects and waste of money. Different machine learning techniques have been developed to fulfill this purpose. From these techniques are Associative Classification (AC) and Decision Tree (DT). The aim of this research is to compare the performance of these two techniques in the prediction of virological response to the standard treatment of HCV from clinical information. 200 patients treated with Interferon and Ribavirin; were analyzed using AC and DT. 150 cases had been used to train the classifiers and 50 cases had been used to test the classifiers. The experiment results showed that the two techniques had given acceptable results however the best accuracy for the AC reached 92% whereas for DT reached 80%.