Abstract: The design, manufacture, and operation of thin-walled
pressure vessels must be based on maximum safe operating pressure
and an adequate factor of safety (FoS). This research paper first
reports experimental evaluation of longitudinal and hoops stresses
based on working pressure as well as maximum pressure; and then
includes a critical study of factor of safety (FoS) in the design of a
glass fiber pressure vessel. Experimental work involved the use of
measuring instruments and the readings from pressure gauges.
Design calculations involved the computations of design stress and
FoS; the latter was based on breaking strength of 55 MPa for the
glass fiber (pressure-vessel material). The experimentally determined
FoS value has been critically compared with the general FoS allowed
in the design of glass fiber pressure vessels.
Abstract: Photonic Crystal Fibers (PCFs) can be used in optical
communications as transmission lines. For this reason, the PCFs with
low confinement loss, low chromatic dispersion, and low nonlinear
effects are highly suitable transmission media. In this paper, we
introduce a new design of index-guiding nanostructured photonic
crystal fiber (IG-NPCF) with ultra-low chromatic dispersion, low
nonlinearity effects, and low confinement loss. Relatively low
dispersion is achieved in the wavelength range of 1200 to 1600nm
using the proposed design. According to the new structure of
nanostructured PCF presented in this study, the chromatic dispersion
slope is -30(ps/km.nm) and the confinement loss reaches below 10-7
dB/km. While in the wavelength range mentioned above at the same
time an effective area of more than 50.2μm2 is obtained.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: This paper investigates the viability of using carbon
fiber reinforced epoxy composites modified with carbon nanotubes to
strengthening reinforced concrete (RC) columns. Six RC columns
was designed and constructed according to ASCE standards. The
columns were wrapped using carbon fiber sheets impregnated with
either neat epoxy or CNTs modified epoxy. These columns were then
tested under concentric axial loading. Test results show that;
compared to the unwrapped specimens; wrapping concrete columns
with carbon fiber sheet embedded in CNTs modified epoxy resulted
in an increase in its axial load resistance, maximum displacement,
and toughness values by 24%, 109% and 232%, respectively. These
results reveal that adding CNTs into epoxy resin enhanced the
confinement effect, specifically, increased the axial load resistance,
maximum displacement, and toughness values by 11%, 6%, and
19%, respectively compared with columns strengthening with carbon
fiber sheet embedded in neat epoxy.
Abstract: Non-destructive testing and evaluation techniques for
assessing the integrity of composite structures are essential to both
reduce manufacturing costs and out of service time of transport means
due to maintenance. In this study, Analyze into non-destructive test
characterization of carbon fiber reinforced plastics (CFRP) internal
and external defects using thermo-graphic camera and transient
thermography method. non-destructive testing were characterized by
defect size (Ø8, Ø10, Ø12, Ø14) and depth (1.2mm, 2.4mm).
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: The main purpose of this work was verify the
influence of the accelerated carbonation in the physical and
mechanical properties of the hybrid composites, reinforced with
micro and nanofibers and composites with microfibers. The
composites were produced by the slurry vacuum dewatering method,
followed by pressing. It was produced using two formulations: 8% of
eucalyptus pulp + 1% of the nanofibrillated cellulose and 9% of
eucalyptus pulp, both were subjected to accelerated carbonation. The
results showed that the accelerated carbonation contributed to
improve the physical and mechanical properties of the hybrid
composites and of the composites reinforced with microfibers
(eucalyptus pulp).
Abstract: We model and simulate the combined effect of fiber
dispersion and frequency chirp of a directly modulated high-speed
laser diode on the figures of merit of a non-amplified 40-Gbps optical
fiber link. We consider both the return to zero (RZ) and non-return to
zero (NRZ) patterns of the pseudorandom modulation bits. The
performance of the fiber communication system is assessed by the
fiber-length limitation due to the fiber dispersion. We study the
influence of replacing standard single-mode fibers by non-zero
dispersion-shifted fibers on the maximum fiber length and evaluate
the associated power penalty. We introduce new dispersion
tolerances for 1-dB power penalty of the RZ and NRZ 40-Gbps
optical fiber links.
Abstract: We have experimentally demonstrated bright-dark
pulses in a nonlinear polarization rotation (NPR) based mode-locked
Erbium-doped fiber laser (EDFL) with a long cavity configuration.
Bright–dark pulses could be achieved when the laser works in the
passively mode-locking regime and the net group velocity dispersion
is quite anomalous. The EDFL starts to generate a bright pulse train
with degenerated dark pulse at the mode-locking threshold pump
power of 35.09 mW by manipulating the polarization states of the
laser oscillation modes using a polarization controller (PC). A split
bright–dark pulse is generated when further increasing the pump
power up to 37.95 mW. Stable bright pulses with no obvious
evidence of a dark pulse can also be generated when further adjusting
PC and increasing the pump power up to 52.19 mW. At higher pump
power of 54.96 mW, a new form of bright-dark pulse emission was
successfully identified with the repetition rate of 29 kHz. The bright
and dark pulses have a duration of 795.5 ns and 640 ns, respectively.
Abstract: As the human race will continue to explore the space
by creating new space transportation means and sending them to other
planets, the enhance of atmospheric reentry study is crucial. In this
context, an analysis of mass recession rate of ablative materials for
thermal shields of reentry spacecrafts is important to be carried out.
The paper describes a new estimation method for calculating the mass
recession of an ablator system made of carbon fiber reinforced plastic
materials. This method is based on Arrhenius equation for low
temperatures and, for high temperatures, on a theory applied for the
recession phenomenon of carbon fiber reinforced plastic materials,
theory which takes into account the presence of the resin inside the
materials. The space mission of USERS spacecraft is considered as a
case study.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: Thermal insulation materials based on natural fibers
represent a very promising area of materials based on natural easy
renewable row sources. These materials may be in terms of the
properties of most competing synthetic insulations, but show
somewhat higher moisture sensitivity and thermal insulation
properties are strongly influenced by the density and orientation of
fibers. The paper described the problem of hygrothermal behavior of
thermal insulation materials based on natural plant and animal fibers.
This is especially the dependence of the thermal properties of these
materials on the type of fiber, bulk density, temperature, moisture and
the fiber orientation.
Abstract: A simple multi-wavelength passively Q-switched
Erbium-doped fiber laser (EDFL) is demonstrated using low cost
multi-walled carbon nanotubes (MWCNTs) based saturable absorber
(SA), which is prepared using polyvinyl alcohol (PVA) as a host
polymer. The multi-wavelength operation is achieved based on
nonlinear polarization rotation (NPR) effect by incorporating 50 m
long photonic crystal fiber (PCF) in the ring cavity. The EDFL
produces a stable multi-wavelength comb spectrum for more than 14
lines with a fixed spacing of 0.48 nm. The laser also demonstrates a
stable pulse train with the repetition rate increases from 14.9 kHz to
25.4 kHz as the pump power increases from the threshold power of
69.0 mW to the maximum pump power of 133.8 mW. The minimum
pulse width of 4.4 μs was obtained at the maximum pump power of
133.8 mW while the highest energy of 0.74 nJ was obtained at pump
power of 69.0 mW.
Abstract: In this study, a liquid phase microextraction by hollow fiber (HF-LPME) combined with high performance liquid chromatography-UV detector was applied to preconcentrate and determine trace levels of Cyproheptadine in human urine and plasma samples. Cyproheptadine was extracted from 10 mL alkaline aqueous solution (pH: 9.81) into an organic solvent (n-octnol) which was immobilized in the wall pores of a hollow fiber. Then was back-extracted into an acidified aqueous solution (pH: 2.59) located inside the lumen of the hollow fiber. This method is simple, efficient and cost-effective. It is based on pH gradient and differences between two aqueous phases. In order to optimize the HF-LPME some affecting parameters including the pH of donor and acceptor phases, the type of organic solvent, ionic strength, stirring rate, extraction time and temperature were studied and optimized. Under optimal conditions enrichment factor, limit of detection (LOD) and relative standard deviation (RSD(%), n=3) were up to 112, 15 μg.L−1 and 2.7, respectively.
Abstract: Tsunami early detection and warning systems have proved to be of ultimate importance, especially after the destructive tsunami that hit Japan in March 2012. Such systems are crucial to inform the authorities of any risk of a tsunami and of the degree of its danger in order to make the right decision and notify the public of the actions they need to take to save their lives. The purpose of this research is to enhance existing tsunami detection and warning systems. We first propose an automated and miniaturized model of an early tsunami detection and warning system. The model for the operation of a tsunami warning system is simulated using the data acquisition toolbox of Matlab and measurements acquired from specified internet pages due to the lack of the required real-life sensors, both seismic and hydrologic, and building a graphical user interface for the system. In the second phase of this work, we implement various satellite image filtering schemes to enhance the acquired synthetic aperture radar images of the tsunami affected region that are masked by speckle noise. This enables us to conduct a post-tsunami damage extent study and calculate the percentage damage. We conclude by proposing improvements to the existing telecommunication infrastructure of existing warning tsunami systems using a migration to IP-based networks and fiber optics links.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: PAN nanofibers reinforced with amine functionalized
carbon nanotubes. The effect of amine functionalization and the
effect of concentration of CNT on the conductivity and mechanical
and morphological properties of composite nanofibers were
examined. 1%CNT-NH2 loaded PAN/CNT nanofiber showed the best
mechanical properties. Conductivity increased with the incorporation
of carbon nanotubes. While an increase of concentration of CNT
increases the diameter of nanofiber, the use of functionalized CNT
results to decrease of diameter of nanofiber.