Abstract: Comparisons of financial development across
countries are central to answering many of the questions on factors
leading to economic development. For this reason this study analyzes
the implications of financial system’s development on country’s
economic development. The aim of the article: to analyze the impact
of financial system’s development on economic development. The
following research methods were used: systemic, logical and
comparative analysis of scientific literature, analysis of statistical
data, time series model (Autoregressive Distributed Lag (ARDL)
Model). The empirical results suggest about positive short and long
term effect of stock market development on GDP per capita.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: This review emphasizes the effectiveness of men’s
participation in preventing domestic violence, and whether nonviolent
(NV) boys’ and men’s perceptions of intimate partner
violence (IPV) prevention programs affect their involvement. The
main goals of this assessment were to investigate (1) how NV men
engaged in anti-violence prevention programs that empower women,
(2) what were the possible perceptions of NV men involved in
prevention programs (3) how to identify effective approaches and
strategies that encouraged NV men to become involved in prevention
programs. This critical review also included the overview of
prevention programs such as: The Mentors in Violence Prevention
Programs (MVP), The White Ribbon Campaign (WRC), and
Domestic Violence Prevention Enhancement and Leadership through
Alliances (DELTA). The review suggested that (1) the expanding
prevention programs need to reach more macro settings such as work
place, faith-based and other community based organizations, and (2)
territory prevention programs should expand through addressing the
long-term effects of violence.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: Higher order ΔΣ Modulator (DSM) is basically an
unstable system. The approximate conditions for stability cannot be
used for the design of a DSM for industrial applications where risk is
involved. The existing second order, single stage, single bit, unity
feedback gain , discrete DSM cannot be used for the normalized full
range (-1 to +1) of an input signal since the DSM becomes unstable
when the input signal is above ±0.55. The stability is also not
guaranteed for input signals of amplitude less than ±0.55. In the
present paper, the above mentioned second order DSM is modified
with input signal dependent forward path gain. The proposed DSM is
suitable for industrial applications where one needs the digital
representation of the analog input signal, during each sampling
period. The proposed DSM can operate almost for the full range of
input signals (-0.95 to +0.95) without causing instability, assuming
that the second integrator output should not exceed the circuit supply
voltage, ±15 Volts.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.
Abstract: Safety is one of the most important considerations
when buying a new car. While active safety aims at avoiding
accidents, passive safety systems such as airbags and seat belts
protect the occupant in case of an accident. In addition to legal
regulations, organizations like Euro NCAP provide consumers with
an independent assessment of the safety performance of cars and
drive the development of safety systems in automobile industry.
Those ratings are mainly based on injury assessment reference values
derived from physical parameters measured in dummies during a car
crash test.
The components and sub-systems of a safety system are designed
to achieve the required restraint performance. Sled tests and other
types of tests are then carried out by car makers and their suppliers
to confirm the protection level of the safety system. A Knowledge
Discovery in Databases (KDD) process is proposed in order to
minimize the number of tests. The KDD process is based on the
data emerging from sled tests according to Euro NCAP specifications.
About 30 parameters of the passive safety systems from different data
sources (crash data, dummy protocol) are first analysed together with
experts opinions. A procedure is proposed to manage missing data
and validated on real data sets. Finally, a procedure is developed to
estimate a set of rough initial parameters of the passive system before
testing aiming at reducing the number of tests.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: Two Lithium Disilicate (LD) glass ceramics based on
SiO2-Li2O-K2O-Al2O3 system were prepared through a glass melting
method. The glass rods were then fabricated into dental crowns via a
hot pressing at 900˚C and 850˚C in order to study the effect of the
pressing temperatures on the phase formation and microstructure of
the glasses. Different samples of as cast glass and heat treated
samples (600˚C and 700˚C) were used to press for investigating the
effect of an initial microstructure on the hot pressing technique. Xray
diffraction (XRD) and scanning electron microscopy (SEM) were
performed to determine the phase formation and microstructure of the
samples, respectively. XRD results show that the main crystalline
structure was Li2Si2O5 by having Li3PO4, Li0.6Al0.6Si2O6, Li2SiO3,
Ca5 (PO4)3F and SiO2 as minor phases. Glass compositions with
different heat treatment temperatures exhibited a difference phase
formations but have less effect during pressing. SEM micrographs
showed the microstructure of Li2Si2O5 as lath-like shape in all
glasses. With increasing the initial heat treatment temperature, the
longer the lath-like crystals of lithium disilicate were increased
especially when using glass heat treatment at 700˚C followed by
pressing at 900˚C. This could be suggested that LD1 heat treatment at
700˚C which pressing at 900˚C presented the best formation by the
hot pressing and compiled microstructure.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.
Abstract: This paper illustrates the effect of nano Magnesium
Hydroxide (MH) loading on the thermal properties of Low Density
Polyethylene (LDPE)/Poly (ethylene-co vinyl acetate) (EVA) nano
composite. Thermal studies were conducted, as it understanding is
vital for preliminary development of new polymeric systems.
Thermal analysis of nanocomposite was conducted using thermo
gravimetric analysis (TGA), and differential scanning calorimetry
(DSC). Major finding of TGA indicated two main stages of
degradation process found at (350 ± 25oC) and (480 ± 25oC)
respectively. Nano metal filler expressed better fire resistance as it
stand over high degree of temperature. Furthermore, DSC analysis
provided a stable glass temperature around 51 (±1oC) and captured
double melting point at 84 (±2oC) and 108 (±2oC). This binary
melting point reflects the modification of nano filler to the polymer
matrix forming melting crystals of folded and extended chain. The
percent crystallinity of the samples grew vividly with increasing filler
content. Overall, increasing the filler loading improved the
degradation temperature and weight loss evidently and a better
process and phase stability was captured in DSC.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: Climate warming would increase rainfall by shifting
precipitation falling form from snow to rain, and would accelerate
snow cover disappearing by increasing snowpack. Using temperature
and precipitation data in the temperature-index snowmelt model, we
evaluated variability of snowfall and continuous snow cover duration
(CSCD) during 1944-2010 over Pelso, central Finland. Mann-
Kendall non-parametric test determined that annual precipitation
increased by 2.69 (mm/year, p
Abstract: Due to the advancement of Internet technology, online
learning is widely used in higher education institutions. Online
learning offers several means of communication, including online
forum. Through online forum, students and instructors are able to
discuss and share their knowledge and expertise without having a
need to attend the face-to-face, ordinary classroom session. The
purposes of this study are to analyze the students’ levels of
participation and critical thinking, types of action and factors
influencing their participation in online forum. A total of 41
postgraduate students undertaking a course in educational technology
from a public university in Malaysia were involved in this study. In
this course, the students participated in a weekly online forum as part
of the course requirement. Based on the log data file extracted from
the online forum, the students’ type of actions (view, add, update,
delete posts) and their levels of participation (passive, moderate or
active) were identified. In addition, the messages posted in the forum
were analyzed to gauge their level of critical thinking. Meanwhile,
the factors that might influence their online forum participation were
measured using a 24-items questionnaire. Based on the log data, a
total of 105 posts were sent by the participants. In addition, the
findings show that (i) majority of the students are moderate
participants, with an average of two to three posts per person, (ii)
viewing posts are the most frequent type of action (85.1%), and
followed by adding post (9.7%). Furthermore, based on the posts
they made, the most frequent type of critical thinking observed was
justification (50 input or 19.0%), followed by linking ideas and
interpretation (47 input or 18%), and novelty (38 input or 14.4%).
The findings indicate that online forum allows for social interaction
and can be used to measure the students’ critical thinking skills. In
order to achieve this, monitoring students’ activities in the online
forum is recommended.