Abstract: Sensory nerves in the foot play an important part in the diagnosis of various neuropathydisorders, especially in diabetes mellitus.However, a detailed description of the anatomical distribution of the nerves is currently lacking. A computationalmodel of the afferent nerves inthe foot may bea useful tool for the study of diabetic neuropathy. In this study, we present the development of an anatomically-based model of various major sensory nerves of the sole and dorsal sidesof the foot. In addition, we presentan algorithm for generating synthetic somatosensory nerve networks in the big-toe region of a right foot model. The algorithm was based on a modified version of the Monte Carlo algorithm, with the capability of being able to vary the intra-epidermal nerve fiber density in differentregionsof the foot model. Preliminary results from the combinedmodel show the realistic anatomical structure of the major nerves as well as the smaller somatosensory nerves of the foot. The model may now be developed to investigate the functional outcomes of structural neuropathyindiabetic patients.
Abstract: Electric vehicles are considered as technology which
can significantly reduce the problems related to road transport such
as increasing GHG emissions, air pollutions and energy import
dependency.
The core objective of this paper is to analyze the current energetic,
ecological and economic characteristics of different types of electric
vehicles.
The major conclusions of this analysis are: The high investments
cost are the major barrier for broad market breakthrough of battery
electric vehicles and fuel cell vehicles. For battery electric vehicles
also the limited driving range states a key obstacle. The analyzed
hybrids could in principle serve as a bridging technology. However,
due to their tank-to-wheel emissions they cannot state a proper
solution for urban areas.
Finally, the most important perception is that also battery electric
vehicles and fuel cell vehicles are environmentally benign solution if
the primary fuel source is renewable.
Abstract: Earlier studies in kinship networks have primarily
focused on observing the social relationships existing between family
relatives. In this study, we pre-identified hubs in the network to
investigate if they could play a catalyst role in the transfer of physical
information. We conducted a case study of a ceremony performed in
one of the families of a small Hindu community – the Uttar Rarhi
Kayasthas. Individuals (n = 168) who resided in 11 geographically
dispersed regions were contacted through our hub-based
representation. We found that using this representation, over 98% of
the individuals were successfully contacted within the stipulated
period. The network also demonstrated a small-world property, with
an average geodesic distance of 3.56.
Abstract: Grid computing is a high performance computing
environment to solve larger scale computational applications. Grid
computing contains resource management, job scheduling, security
problems, information management and so on. Job scheduling is a
fundamental and important issue in achieving high performance in
grid computing systems. However, it is a big challenge to design an
efficient scheduler and its implementation. In Grid Computing, there
is a need of further improvement in Job Scheduling algorithm to
schedule the light-weight or small jobs into a coarse-grained or
group of jobs, which will reduce the communication time,
processing time and enhance resource utilization. This Grouping
strategy considers the processing power, memory-size and
bandwidth requirements of each job to realize the real grid system.
The experimental results demonstrate that the proposed scheduling
algorithm efficiently reduces the processing time of jobs in
comparison to others.
Abstract: In a previously developed fast vortex method, the
diffusion of the vortex sheet induced at the solid wall by the no-slip
boundary conditions was modeled according to the approximation
solution of Koumoutsakos and converted into discrete blobs in the
vicinity of the wall. This scheme had been successfully applied to a
simulation of the flow induced with an impulsively initiated circular
cylinder. In this work, further modifications on this vortex method are
attempted, including replacing the approximation solution by the
boundary-element-method solution, incorporating a new algorithm for
handling the over-weak vortex blobs, and diffusing the vortex sheet
circulation in a new way suitable for high-curvature solid bodies. The
accuracy is thus largely improved. The predictions of lift and drag
coefficients for a uniform flow past a NASA airfoil agree well with the
existing literature.
Abstract: The motorway segment between Tangier and Oued
R’mel has experienced, since the beginning of building works,
significant instability and landslides linked to a number of geological,
hydrogeological and geothermic factors affecting the different
formations.
The landslides observed are not fully understood, despite many
studies conducted on this segment. This study aims at producing new
methods to better explain the phenomena behind the landslides,
taking into account the geotechnical and geothermic contexts. This
analysis builds up on previous studies and geotechnical data collected
in the field.
The final body of data collected shall be processed through the
Plaxis software for a better and customizable view of the landslide
problems in the area, which will help tofind solutions and stabilize
land in the area.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: This paper proposes a new algebraic scheme to design a PID controller for higher order linear time invariant continuous systems. Modified PSO (MPSO) based model order formulation techniques have applied to obtain the effective formulated second order system. A controller is tuned to meet the desired performance specification by using pole-zero cancellation method. Proposed PID controller is attached with both higher order system and formulated second order system. The closed loop response is observed for stabilization process and compared with general PSO based formulated second order system. The proposed method is illustrated through numerical example from literature.
Abstract: This study carried out in order to investigate the
effects of salinity on carbon isotope discrimination (Δ) of shoots and
roots of four sugar beet cultivars (cv) including Madison (British
origin) and three Iranian culivars (7233-P12, 7233-P21 and 7233-P29).
Plants were grown in sand culture medium in greenhouse conditions.
Plants irrigated with saline water (tap water as control, 50 mM, 150
mM, 250 mM and 350 mM of NaCl + CaCl2 in 5 to 1 molar ratio)
from 4 leaves stage for 16 weeks. Carbon isotope discrimination
significantly decreased with increasing salinity. Significant
differences of Δ between shoot and root were observed in all cvs and
all levels of salinity. Madison cv showed lower Δ in shoot and root
than other three cvs at all levels of salinity expect control, but cv
7233-P29 had significantly higher Δ values at saline conditions of 150
mM and above. Therefore, Δ might be applicable, as a useful tool, for
study of salinity tolerance of sugar beet genotypes.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: To understand the material characteristics of singleand
poly-crystals of pure copper, the respective relationships between
crystallographic orientations and microstructures, and the bending
and mechanical properties were examined. And texture distribution
is also analyzed. A bending test is performed in a SEM apparatus and
while its behaviors are observed in situ. Furthermore, some
analytical results related to crystal direction maps, inverse pole
figures, and textures were obtained from EBSD analyses.
Abstract: The distressing flood scenarios that occur in
recent years at the surrounding areas of Sarawak River have
left damages of properties and indirectly caused disruptions of
productive activities. This study is meant to reconstruct a 100-year
flood event that took place in this river basin. Sarawak River Subbasin
was chosen and modeled using the one-dimensional
hydrodynamic modeling approach using InfoWorks River Simulation
(RS), in combination with Geographical Information System (GIS).
This produces the hydraulic response of the river and its floodplains
in extreme flooding conditions. With different parameters introduced
to the model, correlations of observed and simulated data are
between 79% – 87%. Using the best calibrated model, flood
mitigation structures are imposed along the sub-basin. Analysis is
done based on the model simulation results. Result shows that the
proposed retention ponds constructed along the sub-basin provide the
most efficient reduction of flood by 34.18%.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: In this study, a fuzzy-logic based control system was
designed to ensure that time and energy is saved during the operation
of load elevators which are used during the construction of tall
buildings. In the control system that was devised, for the load
elevators to work more efficiently, the energy interval where the
motor worked was taken as the output variable whereas the amount
of load and the building height were taken as input variables. The
most appropriate working intervals depending on the characteristics
of these variables were defined by the help of an expert. Fuzzy expert
system software was formed using Delphi programming language. In
this design, mamdani max-min inference mechanism was used and
the centroid method was employed in the clarification procedure. In
conclusion, it is observed that the system that was designed is
feasible and this is supported by statistical analyses..
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: Simultaneous recovery of copper and DCA from
simulated MEUF concentrated stream was investigated. Effects of
surfactant (DCA) and metal (copper) concentrations, surfactant to
metal molar ratio (S/M ratio), electroplating voltage, EDTA
concentration, solution pH, and salt concentration on metal recovery
and current efficiency were studied. Electric voltage of -0.5 V was
shown to be optimum operation condition in terms of Cu recovery,
current efficiency, and surfactant recovery. Increasing Cu recovery and
current efficiency were observed with increases of Cu concentration
while keeping concentration of DCA constant. However, increasing
both Cu and DCA concentration while keeping S/M ratio constant at
2.5 showed detrimental effect on Cu recovery at DCA concentration
higher than 15 mM. Cu recovery decreases with increasing pH while
current efficiency showed an opposite trend. It is believed that
conductivity is the main cause for discrepancy of Cu recovery and
current efficiency observed at different pH. Finally, it was shown that
EDTA had adverse effect on both Cu recovery and current efficiency
while addition of NaCl salt had negative impact on current efficiency
at concentration higher than 8000 mg/L.
Abstract: Fisheries management all around the world is
hampered by the lack, or poor quality, of critical data on fish
resources and fishing operations. The main reasons for the chronic
inability to collect good quality data during fishing operations is the
culture of secrecy common among fishers and the lack of modern
data gathering technology onboard most fishing vessels. In response,
OLRAC-SPS, a South African company, developed fisheries datalogging
software (eLog in short) and named it Olrac. The Olrac eLog
solution is capable of collecting, analysing, plotting, mapping,
reporting, tracing and transmitting all data related to fishing
operations. Olrac can be used by skippers, fleet/company managers,
offshore mariculture farmers, scientists, observers, compliance
inspectors and fisheries management authorities. The authors believe
that using eLog onboard fishing vessels has the potential to
revolutionise the entire process of data collection and reporting
during fishing operations and, if properly deployed and utilised,
could transform the entire commercial fleet to a provider of good
quality data and forever change the way fish resources are managed.
In addition it will make it possible to trace catches back to the actual
individual fishing operation, to improve fishing efficiency and to
dramatically improve control of fishing operations and enforcement
of fishing regulations.