Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: In first stage of each microwave receiver there is Low
Noise Amplifier (LNA) circuit, and this stage has important rule in
quality factor of the receiver. The design of a LNA in Radio
Frequency (RF) circuit requires the trade-off many importance
characteristics such as gain, Noise Figure (NF), stability, power
consumption and complexity. This situation Forces desingners to
make choices in the desing of RF circuits. In this paper the aim is to
design and simulate a single stage LNA circuit with high gain and
low noise using MESFET for frequency range of 5 GHz to 6 GHz.
The desing simulation process is down using Advance Design
System (ADS). A single stage LNA has successfully designed with
15.83 dB forward gain and 1.26 dB noise figure in frequency of 5.3
GHz. Also the designed LNA should be working stably In a
frequency range of 5 GHz to 6 GHz.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: Protective relays are components of a protection system
in a power system domain that provides decision making element for
correct protection and fault clearing operations. Failure of the
protection devices may reduce the integrity and reliability of the power
system protection that will impact the overall performance of the
power system. Hence it is imperative for power utilities to assess the
reliability of protective relays to assure it will perform its intended
function without failure. This paper will discuss the application of
reliability analysis using statistical method called Life Data Analysis
in Tenaga Nasional Berhad (TNB), a government linked power utility
company in Malaysia, namely Transmission Division, to assess and
evaluate the reliability of numerical overcurrent protective relays from
two different manufacturers.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.
Abstract: In this paper, we propose an architecture for easily
constructing a robot controller. The architecture is a multi-agent
system which has eight agents: the Man-machine interface, Task
planner, Task teaching editor, Motion planner, Arm controller,
Vehicle controller, Vision system and CG display. The controller has
three databases: the Task knowledge database, the Robot database and
the Environment database. Based on this controller architecture, we
are constructing an experimental power distribution line maintenance
robot system and are doing the experiment for the maintenance tasks,
for example, “Bolt insertion task".
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: This paper presents the study of a variable speed wind
energy conversion system based on a Doubly Fed Induction Generator
(DFIG) based on a sliding mode control applied to achieve control of
active and reactive powers exchanged between the stator of the DFIG
and the grid to ensure a Maximum Power Point Tracking (MPPT) of
a wind energy conversion system. The proposed control algorithm is
applied to a DFIG whose stator is directly connected to the grid and
the rotor is connected to the PWM converter. To extract a maximum
of power, the rotor side converter is controlled by using a stator
flux-oriented strategy. The created decoupling control between active
and reactive stator power allows keeping the power factor close to
unity. Simulation results show that the wind turbine can operate at
its optimum energy for a wide range of wind speed.
Abstract: Most high-performance ac drives utilize a current
controller. The controller switches a voltage source inverter (VSI)
such that the motor current follows a set of reference current
waveforms. Fixed-band hysteresis (FBH) current control has been
widely used for the PWM inverter. We want to apply the same
controller for the PWM AC chopper. The aims of the controller is to
optimize the harmonic content at both input and output sides, while
maintaining acceptable losses in the ac chopper and to control in
wide range the fundamental output voltage. Fixed band controller has
been simulated and analyzed for a single-phase AC chopper and are
easily extended to three-phase systems. Simulation confirmed the
advantages and the excellent performance of the modulation method
applied for the AC chopper.
Abstract: Ultra-low-power (ULP) circuits have received
widespread attention due to the rapid growth of biomedical
applications and Battery-less Electronics. Subthreshold region of
transistor operation is used in ULP circuits. Major research challenge
in the subthreshold operating region is to extract the ULP benefits
with minimal degradation in speed and robustness. Process, Voltage
and Temperature (PVT) variations significantly affect the
performance of subthreshold circuits. Designed performance
parameters of ULP circuits may vary largely due to temperature
variations. Hence, this paper investigates the effect of temperature
variation on device and circuit performance parameters at different
biasing voltages in the subthreshold region. Simulation results clearly
demonstrate that in deep subthreshold and near threshold voltage
regions, performance parameters are significantly affected whereas in
moderate subthreshold region, subthreshold circuits are more
immune to temperature variations. This establishes that moderate
subthreshold region is ideal for temperature immune circuits.
Abstract: Equilibrium and stability equations of a thin rectangular plate with length a, width b, and thickness h(x)=C1x+C2, made of functionally graded materials under thermal loads are derived based on the first order shear deformation theory. It is assumed that the material properties vary as a power form of thickness coordinate variable z. The derived equilibrium and buckling equations are then solved analytically for a plate with simply supported boundary conditions. One type of thermal loading, uniform temperature rise and gradient through the thickness are considered, and the buckling temperatures are derived. The influences of the plate aspect ratio, the relative thickness, the gradient index and the transverse shear on buckling temperature difference are all discussed.
Abstract: In this paper the modeling and analysis of Space
Vector Pulse Width Modulation (SVPWM) based Dynamic Voltage
Restorer (DVR) using PSCAD/EMTDC software will be presented in
details. The simulation includes full modeling of the SVPWM
technique used to control the DVR inverter. A test power system
composed of three phase voltage source, sag generator, DVR and
three phase resistive load is used to demonstrate restoration capability
of the DVR. The simulation results of the presented DVR proved
excellent voltage sag mitigation to protect sensitive loads.
Abstract: Distance protection of transmission lines including advanced flexible AC transmission system (FACTS) devices has been a very challenging task. FACTS devices of interest in this paper are static synchronous series compensators (SSSC) and unified power flow controller (UPFC). In this paper, a new algorithm is proposed to detect and classify the fault and identify the fault position in a transmission line with respect to a FACTS device placed in the midpoint of the transmission line. Discrete wavelet transformation and wavelet entropy calculations are used to analyze during fault current and voltage signals of the compensated transmission line. The proposed algorithm is very simple and accurate in fault detection and classification. A variety of fault cases and simulation results are introduced to show the effectiveness of such algorithm.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.