Abstract: Laser interferometric methods have been utilized for the measurement of natural convection heat transfer from a heated vertical flat plate, in the investigation presented here. The study mainly aims at comparing two different fringe orientations in the wedge fringe setting of Mach-Zehnder interferometer (MZI), used for the measurements. The interference fringes are set in horizontal and vertical orientations with respect to the heated surface, and two different fringe analysis methods, namely the stepping method and the method proposed by Naylor and Duarte, are used to obtain the heat transfer coefficients. The experimental system is benchmarked with theoretical results, thus validating its reliability in heat transfer measurements. The interference fringe patterns are analyzed digitally using MATLAB 7 and MOTIC Plus softwares, which ensure improved efficiency in fringe analysis, hence reducing the errors associated with conventional fringe tracing. The work also discuss the relative merits and limitations of the two methods used.
Abstract: We study the dynamic response of a wind turbine
structure subjected to theoretical seismic motions, taking into account
the rotational component of ground shaking. Models are generated
for a shallow moderate crustal earthquake in the Madrid Region
(Spain). Synthetic translational and rotational time histories are
computed using the Discrete Wavenumber Method, assuming a point
source and a horizontal layered earth structure. These are used to
analyze the dynamic response of a wind turbine, represented by a
simple finite element model. Von Mises stress values at different
heights of the tower are used to study the dynamical structural
response to a set of synthetic ground motion time histories
Abstract: Geometric design is an important part of planning
process design for physical highway to fill up basic function of roads,
to give good traffic service. It is found that most of the road safety
problems occur at the horizontal curves and complex-compound
curves. In this paper, review on Sagarinn-Myinsain Portion of Nay
Pyi Taw - Mandalay highway has been conducted in aspect of
geometric design induced road safety condition. Horizontal
alignment of geometric features and curve details are reviewed based
on (AASHTO) standard and revised by Autodesk Land Desktop
Software. Moreover, 85th Percentile Operation Speeds (V85) with
driver confidence on horizontal curves is evaluated in order to obtain
the range of highway safety factor (FS). The length of the selected
highway portion is 13.65 miles and 8 lanes. The results of this study
can be used to investigate the possible hazardous locations in
advance and to revise how design radius and super elevation should
be for better road safety performance for the selected portion.
Moreover, the relationship between highway safety and highway
geometry characteristics can also be known.
Abstract: Investigation of soil properties like Cation Exchange
Capacity (CEC) plays important roles in study of environmental
reaserches as the spatial and temporal variability of this property
have been led to development of indirect methods in estimation of
this soil characteristic. Pedotransfer functions (PTFs) provide an
alternative by estimating soil parameters from more readily available
soil data. 70 soil samples were collected from different horizons of
15 soil profiles located in the Ziaran region, Qazvin province, Iran.
Then, multivariate regression and neural network model (feedforward
back propagation network) were employed to develop a
pedotransfer function for predicting soil parameter using easily
measurable characteristics of clay and organic carbon. The
performance of the multivariate regression and neural network model
was evaluated using a test data set. In order to evaluate the models,
root mean square error (RMSE) was used. The value of RMSE and
R2 derived by ANN model for CEC were 0.47 and 0.94 respectively,
while these parameters for multivariate regression model were 0.65
and 0.88 respectively. Results showed that artificial neural network
with seven neurons in hidden layer had better performance in
predicting soil cation exchange capacity than multivariate regression.
Abstract: Horizontal platform system (HPS) is popularly applied
in offshore and earthquake technology, but it is difficult and
time-consuming for regulation. In order to understand the nonlinear
dynamic behavior of HPS and reduce the cost when using it, this paper
employs differential transformation method to study the bifurcation
behavior of HPS. The numerical results reveal a complex dynamic
behavior comprising periodic, sub-harmonic, and chaotic responses.
Furthermore, the results reveal the changes which take place in the
dynamic behavior of the HPS as the external torque is increased.
Therefore, the proposed method provides an effective means of
gaining insights into the nonlinear dynamics of horizontal platform
system.
Abstract: Surface currents play a major role in the distribution
of contaminants, the connectivity of marine populations, and can
influence the vertical and horizontal distribution of nutrients within
the water column. This paper aims to determine the effects of sea
breeze-wind patterns on the climatology of the surface currents on the
continental shelf surrounding Rottnest Island, WA Australia. The
alternating wind patterns allow for full cyclic rotations of wind
direction, permitting the interpretation of the effect of the wind on the
surface currents. It was found that the surface currents only clearly
follow the northbound Capes Current in times when the Fremantle
Doctor sets in. Surface currents react within an hour to a change of
direction of the wind, allowing southerly currents to dominate during
strong northerly sea breezes, often followed by mixed currents
dominated by eddies in the inter-lying times.
Abstract: From the importance of the conference and its
constructive role in the studies discussion, there must be a strong
organization that allows the exploitation of the discussions in opening
new horizons. The vast amount of information scattered across the
web, make it difficult to find experts, who can play a prominent role
in organizing conferences. In this paper we proposed a new approach
of extracting researchers- information from various Web resources
and correlating them in order to confirm their correctness. As a
validator of this approach, we propose a service that will be useful to
set up a conference. Its main objective is to find appropriate experts,
as well as the social events for a conference. For this application we
us Semantic Web technologies like RDF and ontology to represent
the confirmed information, which are linked to another ontology
(skills ontology) that are used to present and compute the expertise.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: Horizontal wells are proven to be better producers
because they can be extended for a long distance in the pay zone.
Engineers have the technical means to forecast the well productivity
for a given horizontal length. However, experiences have shown that
the actual production rate is often significantly less than that of
forecasted. It is a difficult task, if not impossible to identify the real
reason why a horizontal well is not producing what was forecasted.
Often the source of problem lies in the drilling of horizontal section
such as permeability reduction in the pay zone due to mud invasion
or snaky well patterns created during drilling. Although drillers aim
to drill a constant inclination hole in the pay zone, the more frequent
outcome is a sinusoidal wellbore trajectory. The two factors, which
play an important role in wellbore tortuosity, are the inclination and
side force at bit. A constant inclination horizontal well can only be
drilled if the bit face is maintained perpendicular to longitudinal axis
of bottom hole assembly (BHA) while keeping the side force nil at
the bit. This approach assumes that there exists no formation force at
bit. Hence, an appropriate BHA can be designed if bit side force and
bit tilt are determined accurately. The Artificial Neural Network
(ANN) is superior to existing analytical techniques. In this study, the
neural networks have been employed as a general approximation tool
for estimation of the bit side forces. A number of samples are
analyzed with ANN for parameters of bit side force and the results
are compared with exact analysis. Back Propagation Neural network
(BPN) is used to approximation of bit side forces. Resultant low
relative error value of the test indicates the usability of the BPN in
this area.
Abstract: Taking the provincial capital, labor and energy as
inputs, regional GDP as output from 1995 to 2007, the paper
quantifies the vertical and lateral energy saving potential by
introducing the radial adjustment and slack adjustment of DEA. The
results show that by the vertical, the achievement of energy saving in
2007 is better than their respective historical performances. By
horizontal, in 2007 it can be found that Tianjin, Liaoning, Shanghai
and Yunnan do better in energy saving than other provinces. In
national wide, the higher of energy efficiency, the larger of per capita
GDP and the proportion of the tertiary industry in the national
economy, the more open to the outside, the lower the energy saving
potential demonstrates, while the energy endowment has negative
effect on energy saving potential.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: Two-phase frictional pressure drop data were
obtained for condensation of carbon dioxide in single horizontal
micro tube of inner diameter ranged from 0.6 mm up to 1.6 mm over
mass flow rates from 2.5*10-5 to 17*10-5 kg/s and vapor qualities
from 0.0 to 1.0. The inlet condensing pressure is changed from 33.5
to 45 bars. The saturation temperature ranged from -1.5 oC up to 10
oC. These data have then been compared against three (two-phase)
frictional pressure drop prediction methods. The first method is by
Muller-Steinhagen and Heck (Muller-Steinhagen H, Heck K. A
simple friction pressure drop correlation for two-phase flow in pipes.
Chem. Eng. Process 1986;20:297–308) and that by Gronnerud R.
Investigation of liquid hold-up, flow-resistance and heat transfer in
circulation type evaporators, part IV: two-phase flow resistance in
boiling refrigerants, Annexe 1972. Then the method used by
FriedelL. Improved friction pressures drop in horizontal and vertical
two-phase pipe flow. European Two-Phase Flow Group Meeting,
Paper E2; 1979 June, Ispra, Italy. The methods are used by M.B Ould
Didi et al (2001) “Prediction of two-phase pressure gradients of
refrigerant in horizontal tubes". Int.J.of Refrigeration 25(2002) 935-
947. The best available method for annular flow was that of Muller-
Steinhagen and Heck. It was observed that the peak in the two-phase
frictional pressure gradient is at high vapor qualities.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: A submerged horizontal plate type breakwater is
pointed out as an efficient wave protection device for cage culture in
marine fishery. In order to reveal the wave elimination principle of this
type breakwater, boundary element method is utilized to investigate
this problem. The flow field and the trajectory of water particles are
studied carefully. The flow field analysis shows that: the interaction of
incident wave and adverse current above the plate disturbs the water
domain drastically. This can slow down the horizontal velocity and
vertical velocity of the water particles.
Abstract: In this paper, we present a novel approach to accurately
detect text regions including shop name in signboard images with
complex background for mobile system applications. The proposed
method is based on the combination of text detection using edge
profile and region segmentation using fuzzy c-means method. In the
first step, we perform an elaborate canny edge operator to extract all
possible object edges. Then, edge profile analysis with vertical and
horizontal direction is performed on these edge pixels to detect
potential text region existing shop name in a signboard. The edge
profile and geometrical characteristics of each object contour are
carefully examined to construct candidate text regions and classify the
main text region from background. Finally, the fuzzy c-means
algorithm is performed to segment and detected binarize text region.
Experimental results show that our proposed method is robust in text
detection with respect to different character size and color and can
provide reliable text binarization result.
Abstract: This paper proposes a vertical beamforming concept
to a cellular network employing Fractional Frequency Reuse
technique including with cell sectorization. Two different beams are
utilized in cell-center and cell-edge, separately. The proposed concept
is validated through computer simulation in term of SINR and
channel capacity. Also, comparison when utilizing horizontal and
vertical beam formation is in focus. The obtained results indicate
that the proposed concept can improve the performance of the
cellular networks comparing with the one using horizontal
beamforming.
Abstract: In this manuscript, the LBM is applied for simulating of Mixed Convection in a Lid-Driven cavity with an open side. The cavity horizontal walls are insulated while the west Lid-driven wall is maintained at a uniform temperature higher than the ambient. Prandtl number (Pr) is fixed to 0.71 (air) while Reynolds number (Re) , Richardson number (Ri) and aspect ratio (A) of the cavity are changed in the range of 50-150 , of 0.1-10 and of 1-4 , respectively. The numerical code is validated for the standard square cavity, and then the results of an open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number (Nu) on lid- driven wall decreases and with same Reynolds number (Re) by increasing of aspect ratio (A), Richardson number plays more important role in heat transfer rate.
Abstract: The present paper is an experimental investigation of
roughness effects on nucleate pool boiling of refrigerant R113 on
horizontal circular copper surfaces. The copper samples were treated
by different sand paper grit sizes to achieve different surface
roughness. The average surface roughness of the four samples was
0.901, 0.735, 0.65, and 0.09, respectively. The experiments were
performed in the heat flux range of 8 to 200kW/m2. The heat transfer
coefficient was calculated by measuring wall superheat of the
samples and the input heat flux. The results show significant
improvement of heat transfer coefficient as the surface roughness is
increased. It is found that the heat transfer coefficient of the sample
with Ra=0.901 is 3.4, 10.5, and 38.5% higher in comparison with
surfaces with Ra of 0.735, 0.65, and 0.09 at heat flux of 170 kW/m2.
Moreover, the results are compared with literature data and the well
known Cooper correlation.
Abstract: In this paper, a comparative study of application of
supervised and unsupervised learning algorithms on illumination
invariant face recognition has been carried out. The supervised
learning has been carried out with the help of using a bi-layered
artificial neural network having one input, two hidden and one output
layer. The gradient descent with momentum and adaptive learning
rate back propagation learning algorithm has been used to implement
the supervised learning in a way that both the inputs and
corresponding outputs are provided at the time of training the
network, thus here is an inherent clustering and optimized learning of
weights which provide us with efficient results.. The unsupervised
learning has been implemented with the help of a modified
Counterpropagation network. The Counterpropagation network
involves the process of clustering followed by application of Outstar
rule to obtain the recognized face. The face recognition system has
been developed for recognizing faces which have varying
illumination intensities, where the database images vary in lighting
with respect to angle of illumination with horizontal and vertical
planes. The supervised and unsupervised learning algorithms have
been implemented and have been tested exhaustively, with and
without application of histogram equalization to get efficient results.