Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: The aim of this study is to investigate the relationship
between expectation, satisfaction and loyalty of South Korean
tourists visiting Turkey. In the research, a questionnaire was used as a
data collecting tool. The questionnaires are filled by South Korean
tourists coming to Turkey through package tours and individual. The
survey was conducted in 2014 in Nevsehir (Cappadocia Region) and
Istanbul. Tourist guides and agency staff have helped the
implementation of surveys. The survey questions are composed of 4
parts, which are “demographic characteristics of tourists”, “travel
behavior characteristics”, “perception of expectations on destination
attributes” and “perception of destination loyalty”. 5-point Likert
type scale including 28 destination attributes was used to measure the
expectations of South Korean tourists coming to Turkey. Questions
were directed to the tourists to measure the destination loyalty. The
questions relating to destination loyalty are “Talking about Turkey to
others”, “Recommendation Turkey to others” and “Tourists’
intentions to revisit Turkey”. The basic hypothesis of the research is
that there is a statistically significant relationship among
expectations, satisfactions and destination loyalty of South Korean
tourists coming to Turkey. The results indicated that the expectation
had a significant effect on overall satisfaction. In addition it was seen
that between overall satisfaction of tourists and destination loyalty
had a significant relationship. Based on findings, some suggestions
for tour operators and travel agencies were made.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: A compact Ultra Wide Band (UWB) antenna with coplanar
waveguide feed has been designed and results are verified in
this paper. The antenna has been designed on FR4 substrate with
dielectric constant (εr) of 4.4 and dimensions of 32mm x 26mm x
0.8mm. The presented antenna shows return loss characteristics in the
band of 3.1 to 10.6 GHz as prescribed by FCC, USA. Parametric
studies have been done and results thus obtained have been
presented. Simulated results have been verified on Rohde & Swartz
VNA. The measured results are in good agreement with simulated
results which make the presented antenna suitable to be used for
wearable applications. Performance analysis of antenna has also been
shown in the presence of three layered Human Arm model. Results
obtained in presence of Human Arm model has been compared with
that in free space.
Abstract: Different terms of the Statistical Process Control (SPC)
has sketch in the fuzzy environment. However, Measurement System
Analysis (MSA), as a main branch of the SPC, is rarely investigated
in fuzzy area. This procedure assesses the suitability of the data to be
used in later stages or decisions of the SPC. Therefore, this research
focuses on some important measures of MSA and through a new
method introduces the measures in fuzzy environment. In this
method, which works based on Buckley approach, imprecision and
vagueness nature of the real world measurement are considered
simultaneously. To do so, fuzzy version of the gauge capability (Cg
and Cgk) are introduced. The method is also explained through
example clearly.
Abstract: This paper presents a power control for a Doubly Fed
Induction Generator (DFIG) using in Wind Energy Conversion
System (WECS) connected to the grid. The proposed control strategy
employs two nonlinear controllers, Backstipping (BSC) and slidingmode
controller (SMC) scheme to directly calculate the required
rotor control voltage so as to eliminate the instantaneous errors of
active and reactive powers. In this paper the advantages of BSC and
SMC are presented, the performance and robustness of this two
controller’s strategy are compared between them. First, we present a
model of wind turbine and DFIG machine, then a synthesis of the
controllers and their application in the DFIG power control.
Simulation results on a 1.5MW grid-connected DFIG system are
provided by MATLAB/Simulink.
Abstract: File sharing in networks is generally achieved using
Peer-to-Peer (P2P) applications. Structured P2P approaches are
widely used in adhoc networks due to its distributed and scalability
features. Efficient mechanisms are required to handle the huge
amount of data distributed to all peers. The intrinsic characteristics of
P2P system makes for easier content distribution when compared to
client-server architecture. All the nodes in a P2P network act as both
client and server, thus, distributing data takes lesser time when
compared to the client-server method. CHORD protocol is a resource
routing based where nodes and data items are structured into a 1-
dimensional ring. The structured lookup algorithm of Chord is
advantageous for distributed P2P networking applications. However,
structured approach improves lookup performance in a high
bandwidth wired network it could contribute to unnecessary overhead
in overlay networks leading to degradation of network performance.
In this paper, the performance of existing CHORD protocol on
Wireless Mesh Network (WMN) when nodes are static and dynamic
is investigated.
Abstract: Bloom’s Taxonomy has been changed during the
years. The idea of this writing is about the revision that has happened
in both facts and terms. It also contains case studies of using
cognitive Bloom’s taxonomy in teaching geometric solids to the
secondary school students, affective objectives in a creative
workshop for adults and psychomotor objectives in fixing a
malfunctioned refrigerator lamp. There is also pointed to the
important role of classification objectives in adult education as a way
to prevent memory loss.
Abstract: Phonocardiography is important in appraisal of
congenital heart disease and pulmonary hypertension as it reflects the
duration of right ventricular systoles. The systolic murmur in patients
with intra-cardiac shunt decreases as pulmonary hypertension
develops and may eventually disappear completely as the pulmonary
pressure reaches systemic level. Phonocardiography and auscultation
are non-invasive, low-cost, and accurate methods to assess heart
disease. In this work an objective signal processing tool to extract
information from phonocardiography signal using Wavelet is
proposed to classify the murmur as normal or abnormal. Since the
feature vector is large, a Binary Particle Swarm Optimization (PSO)
with mutation for feature selection is proposed. The extracted
features improve the classification accuracy and were tested across
various classifiers including Naïve Bayes, kNN, C4.5, and SVM.
Abstract: Bicycle Level of Service (BLOS) is a measure for
evaluating street conditions for cyclists. Currently, various methods
are proposed for BLOS. These analytical methods however have
some drawbacks: they usually assume cyclists as users that can share
street facilities with motorized vehicles, it is not easy to link them to
design process and they are not easy to follow. In addition, they only
support a narrow range of cycling facilities and may not be applicable
for all situations. Along this, the current paper introduces various
effective design factors for bicycle-friendly streets. This study
considers cyclists as users of streets who have special needs and
facilities. Therefore, the key factors that influence BLOS based on
different cycling facilities that are proposed by developed guidelines
and literature are identified. The combination of these factors
presents a complete set of effective design factors for bicycle-friendly
streets. In addition, the weight of each factor in existing BLOS
models is estimated and these effective factors are ranked based on
these weights. These factors and their weights can be used in further
studies to propose special bicycle-friendly street design model.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: Residential buildings consume significant amounts of
energy and produce large amount of emissions and waste. However,
there is a substantial potential for energy savings in this sector which
needs to be evaluated over the life cycle of residential buildings. Life
Cycle Assessment (LCA) methodology has been employed to study
the primary energy uses and associated environmental impacts of
different phases (i.e., product, construction, use, end of life, and
beyond building life) for residential buildings. Four different
alternatives of residential buildings in Vancouver (BC, Canada) with
a 50-year lifespan have been evaluated, including High Rise
Apartment (HRA), Low Rise Apartment (LRA), Single family
Attached House (SAH), and Single family Detached House (SDH).
Life cycle performance of the buildings is evaluated for embodied
energy, embodied environmental impacts, operational energy,
operational environmental impacts, total life-cycle energy, and total
life cycle environmental impacts. Estimation of operational energy
and LCA are performed using DesignBuilder software and Athena
Impact estimator software respectively.
The study results revealed that over the life span of the buildings,
the relationship between the energy use and the environmental
impacts are identical. LRA is found to be the best alternative in terms
of embodied energy use and embodied environmental impacts; while,
HRA showed the best life-cycle performance in terms of minimum
energy use and environmental impacts. Sensitivity analysis has also
been carried out to study the influence of building service lifespan
over 50, 75, and 100 years on the relative significance of embodied
energy and total life cycle energy. The life-cycle energy requirements
for SDH are found to be a significant component among the four
types of residential buildings. The overall disclose that the primary
operations of these buildings accounts for 90% of the total life cycle
energy which far outweighs minor differences in embodied effects
between the buildings.
Abstract: Elastomeric polymer foam has been used widely in
the automotive industry, especially for isolating unwanted vibrations.
Such material is able to absorb unwanted vibration due to its
combination of elastic and viscous properties. However, the ‘creep
effect’, poor stress distribution and susceptibility to high
temperatures are the main disadvantages of such a system.
In this study, improvements in the performance of elastomeric
foam as a vibration isolator were investigated using the concept of
Foam Filled Fluid (FFFluid). In FFFluid devices, the foam takes the
form of capsule shapes, and is mixed with viscous fluid, while the
mixture is contained in a closed vessel. When the FFFluid isolator is
affected by vibrations, energy is absorbed, due to the elastic strain of
the foam. As the foam is compressed, there is also movement of the
fluid, which contributes to further energy absorption as the fluid
shears. Also, and dependent on the design adopted, the packaging
could also attenuate vibration through energy absorption via friction
and/or elastic strain.
The present study focuses on the advantages of the FFFluid
concept over the dry polymeric foam in the role of vibration isolation.
This comparative study between the performance of dry foam and the
FFFluid was made according to experimental procedures. The paper
concludes by evaluating the performance of the FFFluid isolator in
the suspension system of a light vehicle. One outcome of this
research is that the FFFluid may preferable over elastomer isolators
in certain applications, as it enables a reduction in the effects of high
temperatures and of ‘creep effects’, thereby increasing the reliability
and load distribution. The stiffness coefficient of the system has
increased about 60% by using an FFFluid sample. The technology
represented by the FFFluid is therefore considered by this research
suitable for application in the suspension system of a light vehicle.
Abstract: The aim of this research is to clarify the difference by
industry segment or product characteristics as regards organisation
management for an open innovation to raise R&D performance. In
particular, the trait of the pharmaceutical industry is defined in
comparison with IT component industry segment. In considering open
innovation, both inter-organisational relation and the management in
an organisation are important issues. As methodology, a questionnaire
was conducted. In conclusion, suitable organisation management
according to the difference in industry segment or product
characteristics became clear.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: In this paper, we propose a new method for threedimensional
object indexing based on D.A.M.C-S.H.C descriptor
(Direct and Analytical Method for Calculating the Spherical
Harmonics Coefficients). For this end, we propose a direct
calculation of the coefficients of spherical harmonics with perfect
precision. The aims of the method are to minimize, the processing
time on the 3D objects database and the searching time of similar
objects to a request object.
Firstly we start by defining the new descriptor using a new
division of 3-D object in a sphere. Then we define a new distance
which will be tested and prove his efficiency in the search for similar
objects in the database in which we have objects with very various
and important size.
Abstract: Biodiesel as an alternative diesel fuel is steadily gaining more attention and significance. However, there are some drawbacks while using biodiesel regarding its properties that requires it to be blended with petrol based diesel and/or additives to improve the fuel characteristics. This study analyses thermal cracking as an alternative technology to improve biodiesel characteristics in which, FAME based biodiesel produced by transesterification of castor oil is fed into a continuous thermal cracking reactor at temperatures range of 450-500°C and flowrate range of 20-40 g/hr. Experiments designed by response surface methodology and subsequent statistical studies show that temperature and feed flowrate significantly affect the products yield. Response surfaces were used to study the impact of temperature and flowrate on the product properties. After each experiment, the produced crude bio-oil was distilled and diesel cut was separated. As shorter chain molecules are produced through thermal cracking, the distillation curve of the diesel cut fitted more with petrol based diesel curve in comparison to the biodiesel. Moreover, the produced diesel cut properties adequately pose within property ranges defined by the related standard of petrol based diesel. Cold flow properties, high heating value as the main drawbacks of the biodiesel are improved by this technology. Thermal cracking decreases kinematic viscosity, Flash point and cetane number.
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: A compound parabolic concentrator (CPC) is a wellknown
non-imaging concentrator that will concentrate the solar
radiation onto receiver (PV cell). One of disadvantage of CPC is has
tall and narrow height compared to its diameter entry aperture area.
Therefore, for economic reason, a truncation had been done by
removed from the top of the full height CPC. This also will lead to
the decreases of concentration ratio but it will be negligible. In this
paper, the flux distribution of untruncated and truncated 2-D hollow
compound parabolic trough concentrator (hCPTC) design is
presented. The untruncated design has initial height H=193.4mm
with concentration ratio C_(2-D)=4. This paper presents the optical
simulation of compound parabolic trough concentrator using raytracing
software TracePro. Results showed that, after the truncation,
the height of CPC reduced 45% from initial height with the
geometrical concentration ratio only decrease 10%. Thus, the cost of
reflector and material dielectric usage can be saved especially at
manufacturing site.
Abstract: The fatigue life of tubular joints commonly found in
offshore industry is not only dependent on the value of hot-spot stress
(HSS), but is also significantly influenced by the through-thethickness
stress distribution characterized by the degree of bending
(DoB). The determination of DoB values in a tubular joint is essential
for improving the accuracy of fatigue life estimation using the stresslife
(S–N) method and particularly for predicting the fatigue crack
growth based on the fracture mechanics (FM) approach. In the
present paper, data extracted from finite element (FE) analyses of
tubular KT-joints, verified against experimental data and parametric
equations, was used to investigate the effects of geometrical
parameters on DoB values at the crown 0°, saddle, and crown 180°
positions along the weld toe of central brace in tubular KT-joints
subjected to axial loading. Parametric study was followed by a set of
nonlinear regression analyses to derive DoB parametric formulas for
the fatigue analysis of KT-joints under axial loads. The tubular KTjoint
is a quite common joint type found in steel offshore structures.
However, despite the crucial role of the DoB in evaluating the fatigue
performance of tubular joints, this paper is the first attempt to study
and formulate the DoB values in KT-joints.