Abstract: This paper focuses on systematic analysis and
controller design of the two-inertia STABILIZATION system,
considering the angular motion on a base body. This approach is
essential to the stabilization system to aim at a target under three or six
degrees of freedom base motion. Four controllers, such as
conventional PDF(Pseudo-Derivative Feedback) controller with
motor speed feedback, PDF controller with load speed feedback,
modified PDF controller with motor-load speed feedback and
feedforward controller added to modified PDF controller, are
suggested to improve reference tracking and disturbance rejection
performance. Characteristics and performance of each controller are
analyzed and validated by simulation in the case of the modified PDF
controller with and without a feedforward controller.
Abstract: This paper addresses the problem of trajectory
tracking control of an underactuated autonomous underwater vehicle
(AUV) in the horizontal plane. The underwater vehicle under
consideration is not actuated in the sway direction, and the system
matrices are not assumed to be diagonal and linear, as often found in
the literature. In addition, the effect of constant bias of environmental
disturbances is considered. Using backstepping techniques and the
tracking error dynamics, the system states are stabilized by forcing
the tracking errors to an arbitrarily small neighborhood of zero. The
effectiveness of the proposed control method is demonstrated through
numerical simulations. Simulations are carried out for an
experimental vehicle for smooth, inertial, two dimensional (2D)
reference trajectories such as constant velocity trajectory (a circle
maneuver – constant yaw rate), and time varying velocity trajectory
(a sinusoidal path – sinusoidal yaw rate).
Abstract: A new Feed-Forward/Feedback Generalized
Minimum Variance Pole-placement Controller to incorporate the
robustness of classical pole-placement into the flexibility of
generalized minimum variance self-tuning controller for Single-Input
Single-Output (SISO) has been proposed in this paper. The design,
which provides the user with an adaptive mechanism, which ensures
that the closed loop poles are, located at their pre-specified positions.
In addition, the controller design which has a feed-forward/feedback
structure overcomes the certain limitations existing in similar poleplacement
control designs whilst retaining the simplicity of
adaptation mechanisms used in other designs. It tracks set-point
changes with the desired speed of response, penalizes excessive
control action, and can be applied to non-minimum phase systems.
Besides, at steady state, the controller has the ability to regulate the
constant load disturbance to zero. Example simulation results using
both simulated and real plant models demonstrate the effectiveness of
the proposed controller.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: Producing companies aspire to high delivery
availability despite appearing disruptions. To ensure high delivery
availability safety stocksare required. Howeversafety stock leads to
additional capital commitment and compensates disruptions instead
of solving the reasons.The intention is to increase the stability in
production by configuring the production planning and control
systematically. Thus the safety stock can be reduced. The largest
proportion of inventory in producing companies is caused by batch
inventory, schedule deviations and variability of demand rates.These
reasons for high inventory levels can be reduced by configuring the
production planning and control specifically. Hence the inventory
level can be reduced. This is enabled by synchronizing the lot size
straightening the demand as well as optimizing the releasing order,
sequencing and capacity control.
Abstract: DSTATCOM is one of the equipments for voltage sag mitigation in power systems. In this paper a new control method for balanced and unbalanced voltage sag mitigation using DSTATCOM is proposed. The control system has two loops in order to regulate compensator current and load voltage. Delayed signal cancellation has been used for sequence separation. The compensator should protect sensitive loads against different types of voltage sag. Performance of the proposed method is investigated under different types of voltage sags for linear and nonlinear loads. Simulation results show appropriate operation of the proposed control system.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: Having done in this study, air-conditioning
automation for patisserie shopwindow was designed. In the cooling
sector it is quite important to cooling up the air temperature in the
shopwindow within short time interval. Otherwise the patisseries
inside of the shopwindow will be spoilt in a few days. Additionally
the humidity is other important parameter for the patisseries kept in
shopwindow. It must be raised up to desired level in a quite short
time. Traditional patisserie shopwindows only allow controlling
temperature manually. There is no humidity control and humidity is
supplied by fans that are directed to the water at the bottom of the
shopwindows. In this study, humidity and temperature sensors
(SHT11), PIC, AC motor controller, DC motor controller, ultrasonic
nebulizer and other electronic circuit members were used to simulate
air conditioning automation for patisserie shopwindow in proteus
software package. The simulation results showed that temperature
and humidity values are adjusted in desired time duration by openloop
control technique. Outer and inner temperature and humidity
values were used for control mechanism.
Abstract: The purpose of this study was to find out the
effectiveness of neurological impress method and repeated reading
technique on reading fluency of children with learning disabilities.
Thirty primary four pupils in three public primary schools
participated in the study. There were two experimental groups and a
control. This research employed a 3 by 2 factorial matrix and the
participants were taught for one session. Two hypotheses were
formulated to guide the research. T-test was used to analyse the data
gathered, and data analysis revealed that pupils exposed to the two
treatment strategies had improvement in their reading fluency. It was
recommended that the two strategies used in the study can be used to
intervene in reading fluency problems in children with learning
disabilities.
Abstract: A study was conducted in greenhouse environment to
determine the response of five tissue-cultured date palm cultivars, Al-
Ahamad, Nabusaif, Barhee, Khalas, and Kasab to irrigation water
salinity of 1.6, 5, 10, or 20 dS/ m. The salinity level of 1.6dS/m, was
used as a control. The effects of high salinity on plant survival were
manifested at 360 days after planting (DAP) onwards. Three
cultivars, Khalas, Kasab and Barhee were able to tolerate 10 dS/m
salinity level at 24 months after the start of study. Khalas tolerated
the highest salinity level of 20 dS/ m and 'Nabusaif' was found to be the
least tolerant cv. The average heights of palms and the number of
fronds were decreased with increasing salinity levels as time
progressed.
Abstract: Software project effort estimation is frequently seen
as complex and expensive for individual software engineers.
Software production is in a crisis. It suffers from excessive costs.
Software production is often out of control. It has been suggested that
software production is out of control because we do not measure.
You cannot control what you cannot measure. During last decade, a
number of researches on cost estimation have been conducted. The
metric-set selection has a vital role in software cost estimation
studies; its importance has been ignored especially in neural network
based studies. In this study we have explored the reasons of those
disappointing results and implemented different neural network
models using augmented new metrics. The results obtained are
compared with previous studies using traditional metrics. To be able
to make comparisons, two types of data have been used. The first
part of the data is taken from the Constructive Cost Model
(COCOMO'81) which is commonly used in previous studies and the
second part is collected according to new metrics in a leading
international company in Turkey. The accuracy of the selected
metrics and the data samples are verified using statistical techniques.
The model presented here is based on Multi-Layer Perceptron
(MLP). Another difficulty associated with the cost estimation studies
is the fact that the data collection requires time and care. To make a
more thorough use of the samples collected, k-fold, cross validation
method is also implemented. It is concluded that, as long as an
accurate and quantifiable set of metrics are defined and measured
correctly, neural networks can be applied in software cost estimation
studies with success
Abstract: A new topology of unified power quality conditioner
(UPQC) is proposed for different power quality (PQ) improvement in
a three-phase four-wire (3P-4W) distribution system. For neutral
current mitigation, a star-hexagon transformer is connected in shunt
near the load along with three-leg voltage source inverters (VSIs)
based UPQC. For the mitigation of source neutral current, the uses of
passive elements are advantageous over the active compensation due
to ruggedness and less complexity of control. In addition to this, by
connecting a star-hexagon transformer for neutral current mitigation
the over all rating of the UPQC is reduced. The performance of the
proposed topology of 3P-4W UPQC is evaluated for power-factor
correction, load balancing, neutral current mitigation and mitigation
of voltage and currents harmonics. A simple control algorithm based
on Unit Vector Template (UVT) technique is used as a control
strategy of UPQC for mitigation of different PQ problems. In this
control scheme, the current/voltage control is applied over the
fundamental supply currents/voltages instead of fast changing APFs
currents/voltages, thereby reducing the computational delay.
Moreover, no extra control is required for neutral source current
compensation; hence the numbers of current sensors are reduced. The
performance of the proposed topology of UPQC is analyzed through
simulations results using MATLAB software with its Simulink and
Power System Block set toolboxes.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.