Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: Because of high ductility, aluminum alloys, have been widely used as an important base of metal forming industries. But the main week point of these alloys is their low strength so in forming them with conventional methods like deep drawing, hydro forming, etc have been always faced with problems like fracture during of forming process. Because of this, recently using of explosive forming method for forming of these plates has been recommended. In this paper free explosive forming of A2024 aluminum alloy is numerically simulated and during it, explosion wave propagation process is studied. Consequences of this simulation can be effective in prediction of quality of production. These consequences are compared with an experimental test and show the superiority of this method to similar methods like hydro forming and deep drawing.
Abstract: In this paper, we use Radial Basis Function Networks
(RBFN) for solving the problem of environmental interference
cancellation of speech signal. We show that the Second Order Thin-
Plate Spline (SOTPS) kernel cancels the interferences effectively.
For make comparison, we test our experiments on two conventional
most used RBFN kernels: the Gaussian and First order TPS (FOTPS)
basis functions. The speech signals used here were taken from the
OGI Multi-Language Telephone Speech Corpus database and were
corrupted with six type of environmental noise from NOISEX-92
database. Experimental results show that the SOTPS kernel can
considerably outperform the Gaussian and FOTPS functions on
speech interference cancellation problem.
Abstract: This paper presents a longitudinal quasi-linear model for the ADMIRE model. The ADMIRE model is a nonlinear model of aircraft flying in the condition of high angle of attack. So it can-t be considered to be a linear system approximately. In this paper, for getting the longitudinal quasi-linear model of the ADMIRE, a state transformation based on differentiable functions of the nonscheduling states and control inputs is performed, with the goal of removing any nonlinear terms not dependent on the scheduling parameter. Since it needn-t linear approximation and can obtain the exact transformations of the nonlinear states, the above-mentioned approach is thought to be appropriate to establish the mathematical model of ADMIRE. To verify this conclusion, simulation experiments are done. And the result shows that this quasi-linear model is accurate enough.
Abstract: People detection from images has a variety of applications such as video surveillance and driver assistance system, but is still a challenging task and more difficult in crowded environments such as shopping malls in which occlusion of lower parts of human body often occurs. Lack of the full-body information requires more effective features than common features such as HOG. In this paper, new features are introduced that exploits global self-symmetry (GSS) characteristic in head-shoulder patterns. The features encode the similarity or difference of color histograms and oriented gradient histograms between two vertically symmetric blocks. The domain-specific features are rapid to compute from the integral images in Viola-Jones cascade-of-rejecters framework. The proposed features are evaluated with our own head-shoulder dataset that, in part, consists of a well-known INRIA pedestrian dataset. Experimental results show that the GSS features are effective in reduction of false alarmsmarginally and the gradient GSS features are preferred more often than the color GSS ones in the feature selection.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: Bloom filter is a probabilistic and memory efficient
data structure designed to answer rapidly whether an element is
present in a set. It tells that the element is definitely not in the set but
its presence is with certain probability. The trade-off to use Bloom
filter is a certain configurable risk of false positives. The odds of a
false positive can be made very low if the number of hash function is
sufficiently large. For spam detection, weight is attached to each set
of elements. The spam weight for a word is a measure used to rate the
e-mail. Each word is assigned to a Bloom filter based on its weight.
The proposed work introduces an enhanced concept in Bloom filter
called Bin Bloom Filter (BBF). The performance of BBF over
conventional Bloom filter is evaluated under various optimization
techniques. Real time data set and synthetic data sets are used for
experimental analysis and the results are demonstrated for bin sizes 4,
5, 6 and 7. Finally analyzing the results, it is found that the BBF
which uses heuristic techniques performs better than the traditional
Bloom filter in spam detection.
Abstract: In the paper we discuss the influence of the route
flexibility degree, the open rate of operations and the production type
coefficient on makespan. The flexible job-open shop scheduling
problem FJOSP (an extension of the classical job shop scheduling) is
analyzed. For the analysis of the production process we used a
hybrid heuristic of the GRASP (greedy randomized adaptive search
procedure) with simulated annealing algorithm. Experiments with
different levels of factors have been considered and compared. The
GRASP+SA algorithm has been tested and illustrated with results for
the serial route and the parallel one.
Abstract: Impurity metals such as manganese and cadmium
from high-tenor cobalt electrolyte solution were selectively removed
by solvent extraction method using Co-D2EHPA after converting the functional group of D2EHPA with Co2+ ions. The process parameters
such as pH, organic concentration, O/A ratio, kinetics etc. were
investigated and the experiments were conducted by batch tests in the laboratory bench scale. Results showed that a significant amount
of manganese and cadmium can be extracted using Co-D2EHPA for the optimum processing of cobalt electrolyte solution at equilibrium pH about 3.5. The McCabe-Thiele diagram, constructed from the
extraction studies showed that 100% impurities can be extracted through four stages for manganese and three stages for cadmium
using O/A ratio of 0.65 and 1.0, respectively. From the stripping study, it was found that 100% manganese and cadmium can be stripped from the loaded organic using 0.4 M H2SO4 in a single
contact. The loading capacity of Co-D2EHPA by manganese and cadmium were also investigated with different O/A ratio as well as
with number of stages of contact of aqueous and organic phases. Valuable information was obtained for the designing of an impurities
removal process for the production of pure cobalt with less trouble in the electrowinning circuit.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: The current work focuses on rephrasing the harmful
effects of mercury that is being released from a number of sources.
Most of the sources are from the industrial waste water. Different
techniques of mercury removal have been discussed and a brief
comparison among these has been made. The experimental work has
been conducted for two most widely used methods of mercury
removal and comparison in terms of their efficiency has been made.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: For lack of the visualization of the ultrasonic detection
method of partial discharge (PD), the ultrasonic detection technology
combined with the X-ray visual detection method (UXV) is proposed.
The method can conduct qualitative analysis accurately and conduct
reliable positioning diagnosis to the internal insulation defects of
GIS, and while it could make up the blindness of the X-ray visual
detection method and improve the detection rate. In this paper, an
experimental model of GIS is used as the trial platform, a variety of
insulation defects are set inside the GIS cavity. With the proposed
method, the ultrasonic method is used to conduct the preliminary
detection, and then the X-ray visual detection is used to locate and
diagnose precisely. Therefore, the proposed UXV technology is
feasible and practical.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: The quality of short term load forecasting can improve the efficiency of planning and operation of electric utilities. Artificial Neural Networks (ANNs) are employed for nonlinear short term load forecasting owing to their powerful nonlinear mapping capabilities. At present, there is no systematic methodology for optimal design and training of an artificial neural network. One has often to resort to the trial and error approach. This paper describes the process of developing three layer feed-forward large neural networks for short-term load forecasting and then presents a heuristic search algorithm for performing an important task of this process, i.e. optimal networks structure design. Particle Swarm Optimization (PSO) is used to develop the optimum large neural network structure and connecting weights for one-day ahead electric load forecasting problem. PSO is a novel random optimization method based on swarm intelligence, which has more powerful ability of global optimization. Employing PSO algorithms on the design and training of ANNs allows the ANN architecture and parameters to be easily optimized. The proposed method is applied to STLF of the local utility. Data are clustered due to the differences in their characteristics. Special days are extracted from the normal training sets and handled separately. In this way, a solution is provided for all load types, including working days and weekends and special days. The experimental results show that the proposed method optimized by PSO can quicken the learning speed of the network and improve the forecasting precision compared with the conventional Back Propagation (BP) method. Moreover, it is not only simple to calculate, but also practical and effective. Also, it provides a greater degree of accuracy in many cases and gives lower percent errors all the time for STLF problem compared to BP method. Thus, it can be applied to automatically design an optimal load forecaster based on historical data.
Abstract: Gastric ulceration is a discontinuity in gastric mucosa, usually occurs due to imbalance between the gastric mucosal protective factors, that is called gastric mucosal barrier, and the aggressive factors, to which the mucosa is exposed. This study was carried out on sixty male Sprague-Dowely rats (12- 16 weeks old) allocated into two groups. The first control group and the second Gastric lesion group which induced by oral administration of a single daily dose of aspirin at a dose of 300 mg/kg body weight for 7 consecutive-days (6% aspirin solution will be prepared and each rat will be given 5 ml of that solution/kg body weight). Blood is collected 1, 2 and 3 weeks after induction of gastric ulceration. Significant increase in serum copper, nitric oxide, and prostaglandin E2 all over the period of experiment. Significant decrease in erythrocyte superoxide dismutase (t-SOD) activities, serum (calcium, phosphorus, glucose and insulin) levels. Non-significant changes in serum sodium and potassium levels are obtained.
Abstract: An attempt has been made to investigate the
machinability of zirconia toughened alumina (ZTA) inserts while
turning AISI 4340 steel. The insert was prepared by powder
metallurgy process route and the machining experiments were
performed based on Response Surface Methodology (RSM) design
called Central Composite Design (CCD). The mathematical model of
flank wear, cutting force and surface roughness have been developed
using second order regression analysis. The adequacy of model has
been carried out based on Analysis of variance (ANOVA) techniques.
It can be concluded that cutting speed and feed rate are the two most
influential factor for flank wear and cutting force prediction. For
surface roughness determination, the cutting speed & depth of cut
both have significant contribution. Key parameters effect on each
response has also been presented in graphical contours for choosing
the operating parameter preciously. 83% desirability level has been
achieved using this optimized condition.
Abstract: One main drawback of intrusion detection system is the
inability of detecting new attacks which do not have known
signatures. In this paper we discuss an intrusion detection method
that proposes independent component analysis (ICA) based feature
selection heuristics and using rough fuzzy for clustering data. ICA is
to separate these independent components (ICs) from the monitored
variables. Rough set has to decrease the amount of data and get rid of
redundancy and Fuzzy methods allow objects to belong to several
clusters simultaneously, with different degrees of membership. Our
approach allows us to recognize not only known attacks but also to
detect activity that may be the result of a new, unknown attack. The
experimental results on Knowledge Discovery and Data Mining-
(KDDCup 1999) dataset.
Abstract: Design and implementation of a novel B-ACOSD CFAR algorithm is presented in this paper. It is proposed for detecting radar target in log-normal distribution environment. The BACOSD detector is capable to detect automatically the number interference target in the reference cells and detect the real target by an adaptive threshold. The detector is implemented as a System on Chip on FPGA Altera Stratix II using parallelism and pipelining technique. For a reference window of length 16 cells, the experimental results showed that the processor works properly with a processing speed up to 115.13MHz and processing time0.29 ┬Ás, thus meets real-time requirement for a typical radar system.