Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: In Geographic Information System, one of the sources
of obtaining needed geographic data is digitizing analog maps and
evaluation of aerial and satellite photos. In this study, a method will
be discussed which can be used to extract vectorial features and
creating vectorized drawing files for aerial photos. At the same time
a software developed for these purpose. Converting from raster to
vector is also known as vectorization and it is the most important step
when creating vectorized drawing files. In the developed algorithm,
first of all preprocessing on the aerial photo is done. These are;
converting to grayscale if necessary, reducing noise, applying some
filters and determining the edge of the objects etc. After these steps,
every pixel which constitutes the photo are followed from upper left
to right bottom by examining its neighborhood relationship and one
pixel wide lines or polylines obtained. The obtained lines have to be
erased for preventing confusion while continuing vectorization
because if not erased they can be perceived as new line, but if erased
it can cause discontinuity in vector drawing so the image converted
from 2 bit to 8 bit and the detected pixels are expressed as a different
bit. In conclusion, the aerial photo can be converted to vector form
which includes lines and polylines and can be opened in any CAD
application.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: Numerical parametric study is conducted to study the effects of ampoule rotation on the flows and the dopant segregation in vertical bridgman (vb) crystal growth. Calculations were performed in unsteady state. The extended darcy model, which includes the time derivative and coriolis terms, has been employed in the momentum equation. It’s found that the convection, and dopant segregation can be affected significantly by ampoule rotation, and the effect is similar to that by an axial magnetic field. Ampoule rotation decreases the intensity of convection and stretches the flow cell axially. When the convection is weak, the flow can be suppressed almost completely by moderate ampoule rotation and the dopant segregation becomes diffusion-controlled. For stronger convection, the elongated flow cell by ampoule rotation may bring dopant mixing into the bulk melt reducing axial segregation at the early stage of the growth. However, if the cellular flow cannot be suppressed completely, ampoule rotation may induce larger radial segregation due to poor mixing.
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: This paper proposes a low-voltage and low-power
fully integrated digitally tuned continuous-time channel selection
filter for WiMAX applications. A 5th-order elliptic low-pass filter is
realized in a Gm-C topology. The bandwidth of the fully differential
filter is reconfigurable from 2.5MHz to 20MHz (8x) for different
requirements in WiMAX applications. The filter is simulated in a
standard 90nm CMOS process. Simulation results show the THD
(@Vout =100mVpp) is less than -66dB. The in-band ripple of the
filter is about 0.15dB. The filter consumes 1.5mW from a supply
voltage of 0.9V.
Abstract: In the context of large volume Big Divisor (nearly)
SLagy D3/D7 μ-Split SUSY [1], after an explicit identification
of first generation of SM leptons and quarks with fermionic superpartners
of four Wilson line moduli, we discuss the identification of
gravitino as a potential dark matter candidate by explicitly calculating
the decay life times of gravitino (LSP) to be greater than age of
universe and lifetimes of decays of the co-NLSPs (the first generation
squark/slepton and a neutralino) to the LSP (the gravitino) to be
very small to respect BBN constraints. Interested in non-thermal
production mechanism of gravitino, we evaluate the relic abundance
of gravitino LSP in terms of that of the co-NLSP-s by evaluating
their (co-)annihilation cross sections and hence show that the former
satisfies the requirement for a potential Dark Matter candidate. We
also show that it is possible to obtain a 125 GeV light Higgs in our
setup.
Abstract: In this paper, a new model order reduction
phenomenon is introduced at the design stage of linear phase digital
IIR filter. The complexity of a system can be reduced by adopting the
model order reduction method in their design. In this paper a mixed
method of model order reduction is proposed for linear IIR filter. The
proposed method employs the advantages of factor division technique
to derive the reduced order denominator polynomial and the reduced
order numerator is obtained based on the resultant denominator
polynomial. The order reduction technique is used to reduce the delay
units at the design stage of IIR filter. The validity of the proposed
method is illustrated with design example in frequency domain and
stability is also examined with help of nyquist plot.
Abstract: The availability of broadband internet and increased
access to computers has been instrumental in the rise of internet
literacy in Malaysia. This development has led to the adoption of
online shopping by many Malaysians. On another note, the
Government has supported the development and production of local
herbal products. This has resulted in an increase in the production and
diversity of products by SMEs. The purpose of this study is to
evaluate the influence of the Malaysian demographic factors and
selected attitudinal characteristics in relation to the online purchasing
of herbal products. In total, 1054 internet users were interviewed
online and Chi-square analysis was used to determine the relationship
between demographic variables and different aspects of online
shopping for herbal products. The overall results show that the
demographic variables such as age, gender, education level, income
and ethnicity were significant when considering the online shopping
antecedents of trust, quality of herbal products, perceived risks and
perceived benefits.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: Encryption protects communication partners from
disclosure of their secret messages but cannot prevent traffic analysis
and the leakage of information about “who communicates with
whom". In the presence of collaborating adversaries, this linkability
of actions can danger anonymity. However, reliably providing
anonymity is crucial in many applications. Especially in contextaware
mobile business, where mobile users equipped with PDAs
request and receive services from service providers, providing
anonymous communication is mission-critical and challenging at the
same time. Firstly, the limited performance of mobile devices does
not allow for heavy use of expensive public-key operations which are
commonly used in anonymity protocols. Moreover, the demands for
security depend on the application (e.g., mobile dating vs. pizza
delivery service), but different users (e.g., a celebrity vs. a normal
person) may even require different security levels for the same
application. Considering both hardware limitations of mobile devices
and different sensitivity of users, we propose an anonymity
framework that is dynamically configurable according to user and
application preferences. Our framework is based on Chaum-s mixnet.
We explain the proposed framework, its configuration
parameters for the dynamic behavior and the algorithm to enforce
dynamic anonymity.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: A feature weighting and selection method is proposed
which uses the structure of a weightless neuron and exploits the
principles that govern the operation of Genetic Algorithms and
Evolution. Features are coded onto chromosomes in a novel way
which allows weighting information regarding the features to be
directly inferred from the gene values. The proposed method is
significant in that it addresses several problems concerned with
algorithms for feature selection and weighting as well as providing
significant advantages such as speed, simplicity and suitability for
real-time systems.
Abstract: In this paper, frequency offset (FO) estimation schemes
robust to the non-Gaussian noise environments are proposed for
orthogonal frequency division multiplexing (OFDM) systems. First,
a maximum-likelihood (ML) estimation scheme in non-Gaussian
noise environments is proposed, and then, the complexity of the
ML estimation scheme is reduced by employing a reduced set of
candidate values. In numerical results, it is demonstrated that the
proposed schemes provide a significant performance improvement
over the conventional estimation scheme in non-Gaussian noise
environments while maintaining the performance similar to the
estimation performance in Gaussian noise environments.
Abstract: One of the most important problems in production planning of flexible manufacturing system (FMS) is machine tool selection and operation allocation problem that directly influences the production costs and times .In this paper minimizing machining cost, set-up cost and material handling cost as a multi-objective problem in flexible manufacturing systems environment are considered. We present a 0-1 integer linear programming model for the multiobjective machine tool selection and operation allocation problem and due to the large scale nature of the problem, solving the problem to obtain optimal solution in a reasonable time is infeasible, Paretoant colony optimization (P-ACO) approach for solving the multiobjective problem in reasonable time is developed. Experimental results indicate effectiveness of the proposed algorithm for solving the problem.
Abstract: The paper evaluates several hundred one-day-ahead
VaR forecasting models in the time period between the years 2004
and 2009 on data from six world stock indices - DJI, GSPC, IXIC,
FTSE, GDAXI and N225. The models model mean using the ARMA
processes with up to two lags and variance with one of GARCH,
EGARCH or TARCH processes with up to two lags. The models are
estimated on the data from the in-sample period and their forecasting
accuracy is evaluated on the out-of-sample data, which are more
volatile. The main aim of the paper is to test whether a model
estimated on data with lower volatility can be used in periods with
higher volatility. The evaluation is based on the conditional coverage
test and is performed on each stock index separately. The primary
result of the paper is that the volatility is best modelled using a
GARCH process and that an ARMA process pattern cannot be found
in analyzed time series.
Abstract: In the present work, the performance of the particle
swarm optimization and the genetic algorithm compared as a typical
geometry design problem. The design maximizes the heat transfer
rate from a given fin volume. The analysis presumes that a linear
temperature distribution along the fin. The fin profile generated using
the B-spline curves and controlled by the change of control point
coordinates. An inverse method applied to find the appropriate fin
geometry yield the linear temperature distribution along the fin
corresponds to optimum design. The numbers of the populations, the
count of iterations and time to convergence measure efficiency.
Results show that the particle swarm optimization is most efficient
for geometry optimization.
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.