Abstract: In this work, we demonstrated vertical RRAM device fabricated at the sidewall of contact hole structures for possible future 3-D stacking integrations. The fabricated devices exhibit polarity dependent bipolar resistive switching with small operation voltage of less than 1V for both set and reset process. A good retention of memory window ~50 times is maintained after 1000s voltage bias.
Abstract: This paper presents a 14-bit cyclic-pipelined Analog to digital converter (ADC) running at 1 MS/s. The architecture is based on a 1.5-bit per stage structure utilizing digital correction for each stage. The ADC consists of two 1.5-bit stages, one shift register delay line, and digital error correction logic. Inside each 1.5-bit stage, there is one gain-boosting op-amp and two comparators. The ADC was implemented in 0.18µm CMOS process and the design has an area of approximately 0.2 mm2. The ADC has a differential input range of 1.2 Vpp. The circuit has an average power consumption of 3.5mA with 10MHz sampling clocks. The post-layout simulations of the design satisfy 12-bit SNDR with a full-scale sinusoid input.
Abstract: In this paper, the design of wide-swing constant transconductance (gm) bias circuit that generates bias voltage for low-noise amplifier (LNA) circuit design by using an off-chip resistor is demonstrated. The overall transconductance (Gm) generated by the constant gm bias circuit is important to maintain the overall gain and noise figure of the LNA circuit. Therefore, investigation is performed to study the variation in Gm with process, temperature and supply voltage (PVT). Temperature and supply voltage are swept from -10 °C to 85 °C and 1.425 V to 1.575 V respectively, while the process conditions are also varied to the extreme and the gm variation is eventually concluded at between -3 % to 7 %. With the slight variation in the gm value, through simulation, at worst condition of state SS, we are able to attain a conversion gain (S21) variation of -3.10 % and a noise figure (NF) variation of 18.71 %. The whole constant gm circuit draws approximately 100 µA from a 1.5V supply and is designed based on 0.13 µm CMOS process.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: Plenty researches have reported techniques to harvest energy from piezoelectric transducer. In the earlier years, the researches mainly report linear energy harvesting techniques whereby interface circuitry is designed to have input impedance that match with the impedance of the piezoelectric transducer. In recent years non-linear techniques become more popular. The non-linear technique employs voltage waveform manipulation to boost the available-for-extraction energy at the time of energy transfer. The fact that non-linear energy extraction provides larger available-for-extraction energy doesn’t mean the linear energy extraction is completely obsolete. In some scenarios, such as where initial power is not available, linear energy extraction is still preferred. A modified Buck Boost circuit which is capable of harvesting piezoelectric energy using both linear and non-linear techniques is reported in this paper. Efficiency of at least 64% can be achieved using this circuit. For linear extraction, the modified Buck Boost circuit is controlled using a fix frequency and duty cycle clock. A voltage sensor and a pulse generator are added as the controller for the non-linear extraction technique.
Abstract: A silicon photomultiplier (SiPM) was designed, fabricated and characterized. The SiPM was based on SACM (Separation of Absorption, Charge and Multiplication) structure, which was optimized for blue light detection in application of positron emission tomography (PET). The achieved SiPM array has a high geometric fill factor of 64% and a low breakdown voltage of about 22V, while the temperature dependence of breakdown voltage is only 17mV/°C. The gain and photon detection efficiency of the device achieved were also measured under illumination of light at 405nm and 460nm wavelengths. The gain of the device is in the order of 106. The photon detection efficiency up to 60% has been observed under 1.8V overvoltage.
Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: Microorganisms can be removed, inhibited or killed by physical agents, physical processes or chemical agents but they have their inherent disadvantages such as increased resistance against antibiotics etc. Since, plants have endless ability to synthesize aromatic substances which act as the master agents for plant defense mechanisms against microorganisms, insects and herbivores. Thus, secondary metabolites or phytochemicals obtained from plants can be used as agents of disease control nowadays. In the present study effect of different concentrations of acetone fraction of leaves and alcohol fraction of inflorescence of Euphorbia pulcherrima on various cytomorphological parameters i.e. cell number, mycelium width, conidial size, conidiophore size etc. of Aspergillus fumigatus has been studied. Change in mycelium/ hyphal cell width, conidium size, conidiophore size etc. was measured with the help of a previously calibrated oculometer. To study effect on morphology, fungal mycelium along with conidiophore and conidia were stained with cotton blue and mounted in lactophenol and observed microscopically. Inhibitory action of the acetone extract of Euphorbia pulcherrima leaf on growth of Aspergillus fumigatus was investigated. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but significant inhibition of growth was started at7.81μg/ml concentration of the extract. Complete inhibition was observed at 15.62μg/ml and above. Microscopic examination revealed that at 3.95, 7.81 and 15.62μg/ml extract concentration hyphal cell width was found to be increased from 1.44μm in control to 3.86, 5.24 and 8.98 μm respectively giving a beaded appearance to the mycelium. Vesicle size was reduced from 24.78x20.08μm (control) to 11.34x10.06μm at 3.95μg/ml concentration. At 7.81 and 15.62μg/ml concentration no phialides and sterigmata were observed. Inhibitory action of the alcohol extract of inflorescence on the growth of Aspergillus fumigatus was also studied. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but complete inhibition was observed at 62.5μg/ml and above. Microscopic examination revealed that hyphal cell width of Aspergillus fumigatus was found to be increased from 1.67μm in control to 5.84μm at MIC i.e. at 62.5μg/ml. Vesicle size was reduced from 44.76x 24.22μm (control) to 11.36x 6.80μm at 15.62μg/ml concentrations. At 31.25 μg/ml and 62.5μg/ml concentration no phialides and sterigmata was found. Spore germination was completely found to be inhibited at 3.95μg/ml concentration. Similarly 92.87% reduction in vesicle size was observed at 15.62μg/ml concentration. It is evident from the results that plant extracts inhibit fungal growth and this inhibition is concentration dependent.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: MOSCAPs of various combinations of Hafnium
oxide and Titanium oxide of varying thickness with Aluminum as gate electrode have been fabricated and electrically characterized.
The effects of voltage stress on the I-V characteristics for prolonged time durations have been studied and compared. Results showed
hard breakdown and negligible degradation of reliability under stress.
Abstract: In this study, the static behavior of super elliptical Winkler plate is analyzed by applying the double side approach method. The lack of information about super elliptical Winkler plates is the motivation of this study and we use the double side approach method to solve this problem because of its superior ability on efficiently treating problems with complex boundary shape. The double side approach method has the advantages of high accuracy, easy calculation procedure and less calculation load required. Most important of all, it can give the error bound of the approximate solution. The numerical results not only show that the double side approach method works well on this problem but also provide us the knowledge of static behavior of super elliptical Winkler plate in practical use.
Abstract: An efficient reintegration of the disabled people in the
family and society should be fulfilled; hence it is strongly needful to assist their diminished functions or to replace the totally lost
functions. Assistive technology helps in neutralizing the impairment.
Recent advancements in embedded systems have opened up a vast
area of research and development for affordable and portable assistive devices for the visually impaired. Granted there are many assistive devices on the market that are able to detect obstacles, and numerous research and development currently in process to
alleviate the cause, unfortunately the cost of devices, size of
devices, intrusiveness and higher learning curve prevents the visually impaired from taking advantage of available devices. This
project aims at the design and implementation of a detachable unit
which is robust, low cost and user friendly, thus, trying to
aggrandize the functionality of the existing white cane, to concede above-knee obstacle detection. The designed obstruction detector
uses ultrasound sensors for detecting the obstructions before direct contact. It bestows haptic feedback to the user in accordance with the position of the obstacle.
Abstract: Pore water pressure is normally because of
consolidation, compaction and water level fluctuation on reservoir.
Measuring, controlling and analyzing of pore water pressure have
significant importance in both of construction and operation period.
Since end of 2002, (dam start up) nature of KARKHEH dam has
been analyzed by using the gathered information from
instrumentation system of dam. In this lecture dam condition after
start up have been analyzed by using the gathered data from located
piezometers in core of dam. According to TERZAGHI equation and
records of piezometers, consolidation lasted around five years during
early years of construction stage, and current pore water pressure in
core of dam is caused by water level fluctuation in reservoir.
Although there is time lag between water level fluctuation and results
of piezometers. These time lags have been checked and the results
clearly show that one of the most important causes of it is distance
between piezometer and reservoir.
Abstract: Thousands of masters athletes participate
quadrennially in the World Masters Games (WMG), yet this cohort
of athletes remains proportionately under-investigated. Due to a
growing global obesity pandemic in context of benefits of physical
activity across the lifespan, the prevalence of obesity in this unique
population was of particular interest. Data gathered on a sub-sample
of 535 football code athletes, aged 31-72 yrs ( =47.4, s =±7.1),
competing at the Sydney World Masters Games (2009) demonstrated
a significantly (p
Abstract: A case study of the generation scheduling optimization
of the multi-hydroplants on the Yuan River Basin in China is reported
in this paper. Concerning the uncertainty of the inflows, the
long/mid-term generation scheduling (LMTGS) problem is solved by
a stochastic model in which the inflows are considered as stochastic
variables. For the short-term generation scheduling (STGS) problem, a
constraint violation priority is defined in case not all constraints are
satisfied. Provided the stage-wise separable condition and low
dimensions, the hydroplant-based operational region schedules
(HBORS) problem is solved by dynamic programming (DP). The
coordination of LMTGS and STGS is presented as well. The
feasibility and the effectiveness of the models and solution methods
are verified by the numerical results.
Abstract: This paper describes fast and efficient method for page segmentation of document containing nonrectangular block. The segmentation is based on edge following algorithm using small window of 16 by 32 pixels. This segmentation is very fast since only border pixels of paragraph are used without scanning the whole page. Still, the segmentation may contain error if the space between them is smaller than the window used in edge following. Consequently, this paper reduce this error by first identify the missed segmentation point using direction information in edge following then, using X-Y cut at the missed segmentation point to separate the connected columns. The advantage of the proposed method is the fast identification of missed segmentation point. This methodology is faster with fewer overheads than other algorithms that need to access much more pixel of a document.
Abstract: This paper presents a new compact analytical model of
the gate leakage current in high-k based nano scale MOSFET by
assuming a two-step inelastic trap-assisted tunneling (ITAT) process
as the conduction mechanism. This model is based on an inelastic
trap-assisted tunneling (ITAT) mechanism combined with a semiempirical
gate leakage current formulation in the BSIM 4 model. The
gate tunneling currents have been calculated as a function of gate
voltage for different gate dielectrics structures such as HfO2, Al2O3
and Si3N4 with EOT (equivalent oxide thickness) of 1.0 nm. The
proposed model is compared and contrasted with santaurus
simulation results to verify the accuracy of the model and excellent
agreement is found between the analytical and simulated data. It is
observed that proposed analytical model is suitable for different highk
gate dielectrics simply by adjusting two fitting parameters. It was
also shown that gate leakages reduced with the introduction of high-k
gate dielectric in place of SiO2.
Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Abstract: According to the increasing utilization in power system, the transmission lines and power plants often operate in stability boundary and system probably lose its stable condition by over loading or occurring disturbance. According to the reasons that are mentioned, the prediction and recognition of voltage instability in power system has particular importance and it makes the network security stronger.This paper, by considering of power system contingencies based on the effects of them on Mega Watt Margin (MWM) and maximum loading point is focused in order to analyse the static voltage stability using continuation power flow method. The study has been carried out on IEEE 14-Bus Test System using Matlab and Psat softwares and results are presented.