Abstract: The river flow forecasting represents a crucial point to employ for improving a management policy addressed to the right use of water resources as well as for conjugating prevention and defense actions against environmental degradation. The difficulties occurring during the field activities encourage the development and implementation of operative computation and measuring methods addressed to time reduction for data acquisition and processing maintaining a good level of accuracy. Therefore, the aim of the present work is to test a new entropy based expeditive methodology for the evaluation of the rating curves on three gauged sections with different geometric and morphological characteristics. The methodology requires the choice of only three verticals along the measure section and the sampling of only the maximum velocity. The results underline how in most conditions the rating curves drawn can replace those built with classic methodologies, simplifying thus the procedures of data monitoring and calculation.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: The aim of this paper is to present current and future
procedures in castings procurement. Differences in procurement are
highlighted. The supplier selection criteria used in practice is
compared to literature findings. Different trends related to supply
chains are presented and it is described how they are reflected in
reality to castings procurement. To fulfil the aim, interviews were
conducted in nine companies using castings. It was found that largest
casting users have the most subcontractor foundries and it is more
typical that they have multiple suppliers for the same parts. Currently
only two companies out of nine purchase castings outside Europe,
but the others are also progressing in the same direction. The main
reason is the need to lower purchasing costs. Another trend is that all
companies want to buy cast components or sub-assemblies instead of
raw castings from foundries. It was found that price is a main
supplier selection criterion. All companies use competitive bidding in
supplier selection.
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: This paper represents the results of long term strength of mortar incorporating Rice Husk Ash (RHA). For these work mortar samples were made according to ASTM standard C 109/C. OPC cement was partially replaced by RHA at 0, 10, 15, 20, 25 and 30 percent replacement level. After casting all samples were kept in controlled environment and curing was done up to 90 days. Test of mortar was performed on 3, 7, 28, 90, 365 and 700 days. It is noticed that OPC mortar shows better strength at early age than mortar having RHA but at 90 days and onward the picture is different. At 700 days it is observed that mortar containing 20% RHA shows better result than any other samples.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.
Abstract: This paper proposes two novel schemes for pilot-aided
integer frequency offset (IFO) estimation in orthogonal frequency
division multiplexing (OFDM)-based digital video broadcastingterrestrial
(DVB-T) systems. The conventional scheme proposed for
estimating the IFO uses only partial information of combinations
that pilots can provide, which stems from a rigorous assumption
that the channel responses of pilots used for estimating the IFO
change very rapidly. Thus, in this paper, we propose the novel IFO
estimation schemes exploiting all information of combinations that
pilots can provide to improve the performance of IFO estimation.
The simulation results show that the proposed schemes are highly
accurate in terms of the IFO detection probability.
Abstract: Human Resource (HR) applications can be used to
provide fair and consistent decisions, and to improve the
effectiveness of decision making processes. Besides that, among
the challenge for HR professionals is to manage organization
talents, especially to ensure the right person for the right job at the
right time. For that reason, in this article, we attempt to describe
the potential to implement one of the talent management tasks i.e.
identifying existing talent by predicting their performance as one of
HR application for talent management. This study suggests the
potential HR system architecture for talent forecasting by using
past experience knowledge known as Knowledge Discovery in
Database (KDD) or Data Mining. This article consists of three
main parts; the first part deals with the overview of HR
applications, the prediction techniques and application, the general
view of Data mining and the basic concept of talent management
in HRM. The second part is to understand the use of Data Mining
technique in order to solve one of the talent management tasks, and
the third part is to propose the potential HR system architecture for
talent forecasting.
Abstract: Independent spanning trees (ISTs) provide a number of advantages in data broadcasting. One can cite the use in fault tolerance network protocols for distributed computing and bandwidth. However, the problem of constructing multiple ISTs is considered hard for arbitrary graphs. In this paper we present an efficient algorithm to construct ISTs on hypercubes that requires minimum resources to be performed.
Abstract: This paper mainly investigates the environmental and
economic impacts of worldwide use of electric vehicles. It can be
concluded that governments have good reason to promote the use of
electric vehicles. First, the global vehicles population is evaluated with
the help of grey forecasting model and the amount of oil saving is
estimated through approximate calculation. After that, based on the
game theory, the amount and types of electricity generation needed by
electronic vehicles are established. Finally, some conclusions on the
government-s attitudes are drawn.
Abstract: In the last 15 years, a number of methods have been proposed for forecasting based on fuzzy time series. Most of the fuzzy time series methods are presented for forecasting of enrollments at the University of Alabama. However, the forecasting accuracy rates of the existing methods are not good enough. In this paper, we compared our proposed new method of fuzzy time series forecasting with existing methods. Our method is based on frequency density based partitioning of the historical enrollment data. The proposed method belongs to the kth order and time-variant methods. The proposed method can get the best forecasting accuracy rate for forecasting enrollments than the existing methods.
Abstract: Volume rendering is widely used in medical CT image
visualization. Applying 3D image visualization to diagnosis
application can require accurate volume rendering with high
resolution. Interpolation is important in medical image processing
applications such as image compression or volume resampling.
However, it can distort the original image data because of edge
blurring or blocking effects when image enhancement procedures
were applied. In this paper, we proposed adaptive tension control
method exploiting gradient information to achieve high resolution
medical image enhancement in volume visualization, where restored
images are similar to original images as much as possible. The
experimental results show that the proposed method can improve
image quality associated with the adaptive tension control efficacy.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Many studies have shown that Artificial Neural
Networks (ANN) have been widely used for forecasting financial
markets, because of many financial and economic variables are nonlinear,
and an ANN can model flexible linear or non-linear
relationship among variables.
The purpose of the study was to employ an ANN models to
predict the direction of the Istanbul Stock Exchange National 100
Indices (ISE National-100).
As a result of this study, the model forecast the direction of the
ISE National-100 to an accuracy of 74, 51%.
Abstract: The lack of security obstructs a large scale de- ployment of the multicast communication model. There- fore, a host of research works have been achieved in order to deal with several issues relating to securing the multicast, such as confidentiality, authentication, non-repudiation, in- tegrity and access control. Many applications require au- thenticating the source of the received traffic, such as broadcasting stock quotes and videoconferencing and hence source authentication is a required component in the whole multicast security architecture. In this paper, we propose a new and efficient source au- thentication protocol which guarantees non-repudiation for multicast flows, and tolerates packet loss. We have simu- lated our protocol using NS-2, and the simulation results show that the protocol allows to achieve improvements over protocols fitting into the same category.
Abstract: The present article deals with a composite casting process that allows to produce bilayer AlSn6-Al strips based on the technique of horizontal continuous casting. In the first part experimental investigations on the production of a single layer AlSn6 strip are described. Afterwards essential results of basic compound casting trials using simple test specimen are presented to define the thermal conditions required for a metallurgical compound between the alloy AlSn6 and pure aluminium. Subsequently, numerical analyses are described. A finite element model was used to examine a continuous composite casting process. As a result of the simulations the main influencing parameters concerning the thermal conditions within the composite casting region could be pointed out. Finally, basic guidance is given for the design of an appropriate composite mould system.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: Vehicular communications play a substantial role in providing safety in transportation by means of safety message exchange. Researchers have proposed several solutions for securing safety messages. Protocols based on a fixed key infrastructure are more efficient in implementation and maintain stronger security in comparison with dynamic structures. These protocols utilize zone partitioning to establish distinct key infrastructure under Certificate Authority (CA) supervision in different regions. Secure anonymous broadcasting (SAB) is one of these protocols that preserves most of security aspects but it has some deficiencies in practice. A very important issue is region change of a vehicle for its mobility. Changing regions leads to change of CA and necessity of having new key set to resume communication. In this paper, we propose solutions for informing vehicles about region change to obtain new key set before entering next region. This hinders attackers- intrusion, packet loss and lessons time delay. We also make key request messages secure by confirming old CA-s public key to the message, hence stronger security for safety message broadcasting is attained.
Abstract: Accurate demand forecasting is one of the most key
issues in inventory management of spare parts. The problem of
modeling future consumption becomes especially difficult for lumpy
patterns, which characterized by intervals in which there is no
demand and, periods with actual demand occurrences with large
variation in demand levels. However, many of the forecasting
methods may perform poorly when demand for an item is lumpy.
In this study based on the characteristic of lumpy demand patterns
of spare parts a hybrid forecasting approach has been developed,
which use a multi-layered perceptron neural network and a
traditional recursive method for forecasting future demands. In the
described approach the multi-layered perceptron are adapted to
forecast occurrences of non-zero demands, and then a conventional
recursive method is used to estimate the quantity of non-zero
demands. In order to evaluate the performance of the proposed
approach, their forecasts were compared to those obtained by using
Syntetos & Boylan approximation, recently employed multi-layered
perceptron neural network, generalized regression neural network
and elman recurrent neural network in this area. The models were
applied to forecast future demand of spare parts of Arak
Petrochemical Company in Iran, using 30 types of real data sets. The
results indicate that the forecasts obtained by using our proposed
mode are superior to those obtained by using other methods.