Abstract: This paper proposes for the first time symbolic
formula of the power spectrum of CMOS Cross Couple Oscillator
and its modified circuit. Many principles existed to derived power
spectrum in microwave textbook such as impedance, admittance
parameters, ABCD, H parameters, etc. It can be compared by graph
of power spectrum which methodology is the best from the point of
view of practical measurement setup such as condition of impedance
parameter which used superposition of current to derived (its current
injection at the other port of the circuit is zero, which is impossible in
reality). Four graphs of impedance parameters of cross couple
oscillator are proposed. After that four graphs of scattering
parameters of CMOS cross coupled oscillator will be shown.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: For schools to be desirable places in which to work, it
is necessary for principals to recognise their teachers’ emotions, and
be sensitive to their needs. This necessitates that principals are
capable to correctly identify their emotionally intelligent behaviours
(EIBs) they need to use in order to be successful leaders. They also
need to have knowledge of their emotional intelligence and be able to
identify the factors and situations that evoke emotion at an
interpersonal level. If a principal is able to do this, then the control
and understanding of emotions and behaviours of oneself and others
could improve vastly. This study focuses on the interpersonal EIBS
of principals affecting the job satisfaction of teachers. The correlation
coefficients in this quantitative study strongly indicate that there is a
statistical significance between the respondents’ level of job
satisfaction, the rating of their principals’ EIBs and how they believe
their principals’ EIBs will affect their sense of job satisfaction. It can
be concluded from the data obtained in this study that there is a
significant correlation between the sense of job satisfaction of
teachers and their principals’ interpersonal EIBs. This means that the
more satisfied a teacher is at school, the more appropriate and
meaningful a principal’s EIBs will be. Conversely, the more
dissatisfied a teacher is at school the less appropriate and less
meaningful a principal’s interpersonal EIBs will be. This implies that
the leaders’ EIBs can be construed as one of the major factors
affecting the job satisfaction of employees.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: The problem of degradation of agricultural residues
from palm oil industry is increasing due to its expansion.
Lignocelloulosic waste from these industry represent large amount of
unutilized resources, this is due to their high lignin content. Since
white rot fungi are capable of degrading lignin, its potential for the
degradation of lignocelloulosic waste from palm oil industry was
accessed. The lignocellluloses content was measured before and after
biodegradation and the rate of reduction was determined. From the
results of the biodegradation, it was observed that hemicellulose
reduces by 22.62%, cellulose by 20.97% and lignin by 10.65% from
the initials lignocelluloses contents. Thus, to improve the digestibility
of palm oil mesocarp fibre, treatment by white rot-fungi is
recommended.
Abstract: Health of a person plays a vital role in the collective
health of his community and hence the well-being of the society as a
whole. But, in today’s fast paced technology driven world, health
issues are increasingly being associated with human behaviors – their
lifestyle. Social networks have tremendous impact on the health
behavior of individuals. Many researchers have used social network
analysis to understand human behavior that implicates their social
and economic environments. It would be interesting to use a similar
analysis to understand human behaviors that have health
implications. This paper focuses on concepts of those behavioural
analyses that have health implications using social networks analysis
and provides possible algorithmic approaches. The results of these
approaches can be used by the governing authorities for rolling out
health plans, benefits and take preventive measures, while the
pharmaceutical companies can target specific markets, helping health
insurance companies to better model their insurance plans.
Abstract: The current-voltage (I-V) characteristics of Pd/n-GaN Schottky barrier were studied at temperatures over room temperature (300-470K). The values of ideality factor (n), zero-bias barrier height (φB0), flat barrier height (φBF) and series resistance (Rs) obtained from I-V-T measurements were found to be strongly temperature dependent while (φBo) increase, (n), (φBF) and (Rs) decrease with increasing temperature. The apparent Richardson constant was found to be 2.1x10-9 Acm-2K-2 and mean barrier height of 0.19 eV. After barrier height inhomogeneities correction, by assuming a Gaussian distribution (GD) of the barrier heights, the Richardson constant and the mean barrier height were obtained as 23 Acm-2K-2 and 1.78eV, respectively. The corrected Richardson constant was very closer to theoretical value of 26 Acm-2K-2.
Abstract: Lots of motors have been being used in industry.
Therefore many researchers have studied about the failure diagnosis of
motors. In this paper, the effect of measuring environment for
diagnosis of gear fault connected to a motor shaft is studied. The fault
diagnosis is executed through the comparison of normal gear and
abnormal gear. The measured FFT data are compared with the normal
data and analyzed for q-axis current, noise and vibration. For bad and
good environment, the diagnosis results are compared. From these, it
is shown that the bad measuring environment may not be able to detect
exactly the motor gear fault. Therefore it is emphasized that the
measuring environment should be carefully prepared.
Abstract: In this work, we attempt to associate firm
characteristics with innovative activity. We collect microdata from
listed firms of selected Eurozone Country-members, after the
beginning of 2007 financial crisis. The following literature, several
indicators of growth and performance were selected and tested for
their ability to interpret innovative activity. The main scope is to
examine the possible differences in performance and growth between
innovative and non-innovative firms, during a severe recession.
Additionally to that, a special focus will be held on whether
macroeconomic performance and national innovation system,
determines the extent of innovators' performance. Preliminary
findings, through correlation matrices and non-parametric tests,
strongly indicate the positive relation between innovative activity and
most of the measures used (profitability, size, employment),
confirming that even during a recessionary period, innovative firms
not only survive but also seem to succeed better economic results in
almost all indexes relative to non-innovative. However, even though
innovators seem to perform better in all economies examined, the
extent of that performance seems to be strongly affected by the
supportive mechanisms (financial and structural) that their country
provides. Thus, it is clear, that the technologically intensive 'gap'
between European South and North, during the economic crisis,
became chaotic, due to the harsh austerity measures and reduced
budgets in those countries, even in sectors with high potentials in
economic activity and employment, impairing the effects of crisis and
enhancing the vicious circle of recession.
Abstract: Predicting earnings management is vital for the capital
market participants, financial analysts and managers. The aim of this
research is attempting to respond to this query: Is there a significant
difference between the regression model and neural networks’
models in predicting earnings management, and which one leads to a
superior prediction of it? In approaching this question, a Linear
Regression (LR) model was compared with two neural networks
including Multi-Layer Perceptron (MLP), and Generalized
Regression Neural Network (GRNN). The population of this study
includes 94 listed companies in Tehran Stock Exchange (TSE)
market from 2003 to 2011. After the results of all models were
acquired, ANOVA was exerted to test the hypotheses. In general, the
summary of statistical results showed that the precision of GRNN did
not exhibit a significant difference in comparison with MLP. In
addition, the mean square error of the MLP and GRNN showed a
significant difference with the multi variable LR model. These
findings support the notion of nonlinear behavior of the earnings
management. Therefore, it is more appropriate for capital market
participants to analyze earnings management based upon neural
networks techniques, and not to adopt linear regression models.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: The paper aims to evaluate the effect of online
advertising on consumer purchase behavior in Malaysian
organizations. The paper has potential to extend and refine theory. A
survey was distributed among Students of UTM university during the
winter 2014 and 160 responses were collected. Regression analysis
was used to test the hypothesized relationships of the model. Result
shows that the predictors (cost saving factor, convenience factor and
customized product or services) have positive impact on intention to
continue seeking online advertising.
Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: The present study analyzed the effect of discrimination
experience on the life satisfaction in women with severe disabilities
and the mediating effect of disability acceptance. In verifying this
mediating effect of disability acceptance between discrimination
experience and life satisfaction, both discrimination experience and
disability acceptance were found to be statistically significant in the
first and second phases. Disability acceptance was found to have a
mediating effect on the relationship between discrimination
experience and life satisfaction. Based on this finding, measures for
enhancing the quality of life in individuals with disabilities that
experience low levels of life satisfaction were proposed.
Abstract: The consumption of food contaminated with molds
(microscopic filamentous fungi) and their toxic metabolites results in
the development of food-borne mycotoxicosis. The spores of molds
are ubiquitously spread in the environment and can be detected
everywhere. Ochratoxin A is a toxic and potentially carcinogenic
fungal toxin found in a variety of food commodities. In this study, the
mycological quality of various ready-to-eat local and imported pork
meat and meat byproducts sold in Egyptian markets were assessed
and the presence of various molds was determined in pork used as a
raw material, edible organs as liver and kidney as well as in
fermented raw meat by-products. The study assessed the mycological
quality of pork raw meat and their by-products sold in commercial
shops in Cairo, Egypt. Mycological analysis was conducted on
(n=110) samples which included pig’s livers and kidneys from
Egyptian Bassatin slaughter house; local and imported processed
pork meat by-products from Egyptian pork markets. The isolates
were identified using traditional mycological and biochemical tests.
All kidney and liver samples were positive to molds growth while all
byproducts were negative. Ochratoxin A levels were quantitatively
analyzed using the high performance liquid chromatography (HPLC)
and the highest results were present in kidney 7.51 part per billion
(ppb) followed by minced meat 6.19 ppb generally the local samples
showed higher levels than the imported ones. To the best of our
knowledge, this is the first report on mycotoxins detection and
quantification from pork by-products in Egypt.
Abstract: Structural failure is caused mainly by damage that
often occurs on structures. Many researchers focus on to obtain very
efficient tools to detect the damage in structures in the early state. In
the past decades, a subject that has received considerable attention in
literature is the damage detection as determined by variations in the
dynamic characteristics or response of structures. The study presents
a new damage identification technique. The technique detects the
damage location for the incomplete structure system using output
data only. The method indicates the damage based on the free
vibration test data by using ‘Two Points Condensation (TPC)
technique’. This method creates a set of matrices by reducing the
structural system to two degrees of freedom systems. The current
stiffness matrices obtain from optimization the equation of motion
using the measured test data. The current stiffness matrices compare
with original (undamaged) stiffness matrices. The large percentage
changes in matrices’ coefficients lead to the location of the damage. TPC technique is applied to the experimental data of a simply
supported steel beam model structure after inducing thickness change
in one element, where two cases consider. The method detects the
damage and determines its location accurately in both cases. In
addition, the results illustrate these changes in stiffness matrix can be
a useful tool for continuous monitoring of structural safety using
ambient vibration data. Furthermore, its efficiency proves that this
technique can be used also for big structures.