Abstract: This paper describes the proficient way of choosing the cluster head based on dominating set algorithm in a wireless sensor network (WSN). The algorithm overcomes the energy deterioration problems by this selection process of cluster heads. Clustering algorithms such as LEACH, EEHC and HEED enhance scalability in WSNs. Dominating set algorithm keeps the first node alive longer than the other protocols previously used. As the dominating set of cluster heads are directly connected to each node, the energy of the network is saved by eliminating the intermediate nodes in WSN. Security and trust is pivotal in network messaging. Cluster head is secured with a unique key. The member can only connect with the cluster head if and only if they are secured too. The secured trust model provides security for data transmission in the dominated set network with the group key. The concept can be extended to add a mobile sink for each or for no of clusters to transmit data or messages between cluster heads and to base station. Data security id preferably high and data loss can be prevented. The simulation demonstrates the concept of choosing cluster heads by dominating set algorithm and trust evaluation using DSTE. The research done is rationalized.
Abstract: Dysphasia is difficulty in swallowing food because of oral cavity impairments induced by stroke, muscle damage, tumor. Intermittent oro-esophageal (IOE) tube feeding is one of the well-known feeding methods for the dysphasia patients. However, it is hard to insert at the proper position in esophagus. In this study, we design and fabricate the IOE tube guide using 3-dimensional (3D) printer. The printed IOE tube is tested in a mannequin (Airway Management Trainer, Co., Ltd., Copenhagen, Denmark) mimicking human’s esophagus. The gag reflex point is measured as the design point in the mannequin. To avoid the gag reflex, we design various shapes of IOE tube guide. One structure is separated into three parts; biting part, part through oral cavity, connecting part to oro-esophageal. We designed 6 types of IOE tube guide adjusting length and angle of these three parts. To evaluate the IOE tube guide, it is inserted in the mannequin, and through the inserted guide, an endoscopic camera successfully arrived at the oro-esophageal. We had planned to apply this mannequin-based design experience to patients in near future.
Abstract: Composite column is a structural member that uses a combination of structural steel shapes, pipes or tubes with or without reinforcing steel bars and reinforced concrete to provide adequate load carrying capacity to sustain either axial compressive loads alone or a combination of axial loads and bending moments. Composite construction takes the advantages of the speed of construction, light weight and strength of steel, and the higher mass, stiffness, damping properties and economy of reinforced concrete. The most usual types of composite columns are the concrete filled steel tubes and the partially or fully encased steel profiles. Fully encased composite column (FEC) provides compressive strength, stability, stiffness, improved fire proofing and better corrosion protection. This paper reports experimental and numerical investigations of the behaviour of concrete encased steel composite columns subjected to short-term axial load. In this study, eleven short FEC columns with square shaped cross section were constructed and tested to examine the load-deflection behavior. The main variables in the test were considered as concrete compressive strength, cross sectional size and percentage of structural steel. A nonlinear 3-D finite element (FE) model has been developed to analyse the inelastic behaviour of steel, concrete, and longitudinal reinforcement as well as the effect of concrete confinement of the FEC columns. FE models have been validated against the current experimental study conduct in the laboratory and published experimental results under concentric load. It has been observed that FE model is able to predict the experimental behaviour of FEC columns under concentric gravity loads with good accuracy. Good agreement has been achieved between the complete experimental and the numerical load-deflection behaviour in this study. The capacities of each constituent of FEC columns such as structural steel, concrete and rebar's were also determined from the numerical study. Concrete is observed to provide around 57% of the total axial capacity of the column whereas the steel I-sections contributes to the rest of the capacity as well as ductility of the overall system. The nonlinear FE model developed in this study is also used to explore the effect of concrete strength and percentage of structural steel on the behaviour of FEC columns under concentric loads. The axial capacity of FEC columns has been found to increase significantly by increasing the strength of concrete.
Abstract: In recent years, focus-group discussions, as a resources of qualitative facts collection, have gained popularity amongst practices within social science studies. Despite this popularity, studying qualitative information, particularly focus-group meetings, creates a challenge to most practitioner inspectors. The Mons, also known as Raman is considered to be one of the earliest peoples in mainland South-East Asia and to be found in scattered communities in Thailand, around the central valley and even in Bangkok. The present project responds to the needs identified traditional Mon set menus based on the participation of Bang Kadi community in Bangkok, Thailand. The aim of this study was to generate Mon food set menus based on the participation of the community and to study Mon food in set menus of Bang Kadi population by focus-group interviews and discussions during May to October 2015 of Bang Kadi community in Bangkok, Thailand. Data were collected using (1) focus group discussion between the researcher and 147 people in the community, including community leaders, women of the community and the elderly of the community (2) cooking between the researcher and 22 residents of the community. After the focus group discussion, the results found that Mon set menus of Bang Kadi residents involved of Kang Neng Kua-dit, Kang Luk-yom, Kang Som-Kajaeb, Kangleng Puk-pung, Yum Cha-cam, Pik-pa, Kao-new dek-ha and Num Ma-toom and the ingredients used in cooking are mainly found in local and seasonal regime. Most of foods in set menus are consequent from local wisdom.
Abstract: Various players are part of the game in an asymmetric war, all making efforts to provide human security to their own adherents. Although a fragile state is not able to provide sufficient and comprehensive services, it still provides special services and security to the elite; the insurgents as well provide services and security to their associates. The humanitarian organisations, on the other hand, provide some fundamental elements of human security, but only in the regions, they are able to access when possible (if possible). The counterinsurgents (security forces of the state and intervention forces) operate within a narrow band defined by the vision of the responsibility to protect and the perspective of the resolution of the conflict through combat; hence, the possibility to provide human security is shaken at this end. This article examines how each player provides human security from the perspective of freedom from want in order to secure basic and strategic needs, freedom from fear through providing protection against all kinds of violence, and the freedom to live in dignity. It identifies a vicious cycle caused by the intervention of the different players causing a centrifugal force that may lead to disintegration of the nation under war.
Abstract: Cement is a basic material used for building construction. Chromium as an indelible non-volatile trace element of raw materials occurs in cement clinker in the trivalent or hexavalent form. Hexavalent form of chromium is harmful and allergenic having very high water solubility and thus can easily come into contact with the human skin. The paper is aimed at analyzing the content of total chromium in Portland cements and leaching rate of hexavalent chromium in various leachants: Deionized water, Britton-Robinson buffer, used to simulate the natural environment, and hydrochloric acid (HCl). The concentration of total chromium in Portland cement samples was in a range from 173.2 to 218.5 mg/kg. The content of dissolved hexavalent chromium ranged 0.23-3.19, 2.0-5.78 and 8.88-16.25 mg/kg in deionized water, Britton-Robinson solution and hydrochloric acid, respectively. The calculated leachable fraction of Cr(VI) from cement samples was observed in the range 0.1--7.58 %.
Abstract: Fluid intelligence declines along with age, but it can be developed. For this reason, increasing fluid intelligence in young adults can be possible. This study examined the effects of a two-month treadmill exercise program on fluid intelligence. The researcher designed a treadmill exercise program to promote cardiorespiratory fitness. Thirty-eight healthy voluntary students from the Boromarajonani College of Nursing, Chon Buri were assigned randomly to an exercise group (n=18) and a control group (n=20). The experiment consisted of three sessions: The baseline session consisted of measuring the VO2max, electroencephalogram and behavioral response during performed the Raven Progressive Matrices (RPM) test, a measure of fluid intelligence. For the exercise session, an experimental group exercises using treadmill training at 60 % to 80 % maximum heart rate for 30 mins, three times per week, whereas the control group did not exercise. For the following two sessions, each participant was measured the same as baseline testing. The data were analyzed using the t-test to examine whether there is significant difference between the means of the two groups. The results showed that the mean VO2 max in the experimental group were significantly more than the control group (p
Abstract: The present study investigated various forms of disciplinary procedures or punishment used by teachers in secondary schools in Calabar Municipality, Nigera. There are agitations amongst parents and educators on the use of corporal punishment as a disciplinary measure against children. Those against the use of corporal punishment argue that this form of punishment does not teach, it only terminates behaviour temporarily and inculcates violence. Those in support are of the view that corporal punishment serves as a deterrent to others. This study sought to find out the most common measure of discipline employed by teachers in private and public schools. The study had three objectives, three research questions and two hypotheses. The design of the present study was the ex-post facto descriptive survey, since variables under study were not manipulated by the researcher. Teachers in Calabar Municipal Secondary Schools formed the population. A sample of 160 teachers was used for the study. The data collection instrument was a facts finding questionnaire titled Disciplinary Procedures Inventory. Data collected were analyzed using simple percentages and chi-square. The major findings were that physical measures such as flogging, exercise/drills, and painful postures were commonly used by teachers in secondary schools. It was also found that these measures were more often used in public schools. It was recommended that teachers should rather employ non-violent techniques of discipline than physical punishment.
Abstract: Structures such as buildings, bridges, dams, wind turbines etc. need to be maintained against various factors such as deterioration, excessive loads, environment, temperature, etc. Choosing an appropriate monitoring system is important for determining any critical damage to a structure and address that to avoid any adverse consequence. Structural Health Monitoring (SHM) has emerged as an effective technique to monitor the health of the structures. SHM refers to an ongoing structural performance assessment using different kinds of sensors attached to or embedded in the structures to evaluate their integrity and safety to help engineers decide on rehabilitation measures. Ability of SHM in identifying the location and severity of structural damages by considering any changes in characteristics of the structures such as their frequency, stiffness and mode shapes helps engineers to monitor the structures and take the most effective corrective actions to maintain their safety and extend their service life. The main objective of this study is to review the overall SHM process specifically determining the natural frequency of an instrumented simply-supported concrete beam using modal testing and finite element model updating.
Abstract: The present experimental study insights the decontamination of instantaneous velocity fluctuations captured by Acoustic Doppler Velocimeter (ADV) in gravel-bed streams to ascertain near-bed turbulence for low Reynolds number. The interference between incidental and reflected pulses produce spikes in the ADV data especially in the near-bed flow zone and therefore filtering the data are very essential. Nortek’s Vectrino four-receiver ADV probe was used to capture the instantaneous three-dimensional velocity fluctuations over a non-cohesive bed. A spike removal algorithm based on the acceleration threshold method was applied to note the bed roughness and its influence on velocity fluctuations and velocity power spectra in the carrier fluid. The velocity power spectra of despiked signals with a best combination of velocity threshold (VT) and acceleration threshold (AT) are proposed which ascertained velocity power spectra a satisfactory fit with the Kolmogorov “–5/3 scaling-law” in the inertial sub-range. Also, velocity distributions below the roughness crest level fairly follows a third-degree polynomial series.
Abstract: In this paper, a two-dimensional method is developed to simulate the fillet welds in a stiffened cylindrical shell, using finite element method. The stiffener material is aluminum 2519. The thermo-elasto-plastic analysis is used to analyze the thermo-mechanical behavior. Due to the high heat flux rate of the welding process, two uncouple thermal and mechanical analysis are carried out instead of performing a single couple thermo-mechanical simulation. In order to investigate the effects of the welding procedures, two different welding techniques are examined. The resulted residual stresses and distortions due to different welding procedures are obtained. Furthermore, this study employed the technique of element birth and death to simulate the weld filler variation with time in fillet welds. The obtained results are in good agreement with the published experimental and three-dimensional numerical simulation results. Therefore, the proposed 2D modeling technique can effectively give the corresponding results of 3D models. Furthermore, by inspection of the obtained residual hoop and transverse stresses and angular distortions, proper welding procedure is suggested.
Abstract: A methodology based on wavelets is proposed for the automatic location and delimitation of defects in limestone plates. Natural defects include dark colored spots, crystal zones trapped in the stone, areas of abnormal contrast colors, cracks or fracture lines, and fossil patterns. Although some of these may or may not be considered as defects according to the intended use of the plate, the goal is to pair each stone with a map of defects that can be overlaid on a computer display. These layers of defects constitute a database that will allow the preliminary selection of matching tiles of a particular variety, with specific dimensions, for a requirement of N square meters, to be done on a desktop computer rather than by a two-hour search in the storage park, with human operators manipulating stone plates as large as 3 m x 2 m, weighing about one ton. Accident risks and work times are reduced, with a consequent increase in productivity. The base for the algorithm is wavelet decomposition executed in two instances of the original image, to detect both hypotheses – dark and clear defects. The existence and/or size of these defects are the gauge to classify the quality grade of the stone products. The tuning of parameters that are possible in the framework of the wavelets corresponds to different levels of accuracy in the drawing of the contours and selection of the defects size, which allows for the use of the map of defects to cut a selected stone into tiles with minimum waste, according the dimension of defects allowed.
Abstract: With digitalization increasingly changing the rules of competition, firms face the need to adapt and assimilate digital technologies in order to remain competitive. Firms can choose from various possibilities to integrate digital technologies including the option to embed digital technologies aiming to innovate products or to develop digital products. However, the question of which specific factors influence a firm’s decision to pursue digital product innovation remains unanswered in research. By adopting the Technology-Organization-Environment (TOE)-framework we have designed a qualitative exploratory study including eleven German practitioners to investigate relevant contingency factors. Our results indicate that the most critical factors for a company’s decision to pursue digital product innovation can be found in the technological and environmental dimensions, namely customers, competitive pressure, technological change, as well as digitalization fit.
Abstract: Vacuum flat plate solar thermal collectors offer several advantages over other collectors namely the excellent optical and thermal characteristics they exhibit due to a combination of their wide surface area and high vacuum thermal insulation. These characteristics can offer a variety of applications for industrial process heat as well as for building integration as they are much thinner than conventional collectors making installation possible in limited spaces. However, many technical challenges which need to be addressed to enable wide scale adoption of the technology still remain. This paper will discuss the challenges, expectations and requirements for the flat-plate vacuum solar collector development. In addition, it will provide an overview of work undertaken in Ulster University, Loughborough University, and the University of Warwick on flat-plate vacuum solar thermal collectors. Finally, this paper will present a detailed experimental investigation on the development of a vacuum panel with a novel sealing method which will be used to accommodate a novel slim hydroformed solar absorber.
Abstract: The present study addresses the problem of ammonia evaporation during filling of a vertical cylindrical tank and the influence of various external factors on the stability of storage by determining the conditions for minimum evaporation. Numerical simulation is carried out by solving the governing equations namely, continuity, momentum, energy, and diffusion of species. The effect of temperature of surrounding air, the filling speed of the reservoir and the temperature of the filling liquid ammonia on the evaporation rate is investigated. Results show that the temperature of the filling liquid has little effect on the liquid ammonia for a short period, which, in fact, is function of the filling speed. The evaporation rate along the free surface of the liquid is non-uniform. The inlet temperature affects the vapor ammonia temperature because of pressure increase. The temperature of the surrounding air affects the temperature of the vapor phase rather than the liquid phase. The maximum of evaporation is reached at the final step of filling. In order to minimize loss of ammonia vapors automatically causing losses in quantity of the liquid stored, it is suggested to ensure the proper insulation for the walls and roof of the reservoir and to increase the filling speed.
Abstract: TRACE is developed by U.S. NRC for the nuclear
power plants (NPPs) safety analysis. We focus on the establishment
and application of TRACE/FRAPTRAN/SNAP models for Chinshan
NPP (BWR/4) spent fuel pool in this research. The geometry is 12.17
m × 7.87 m × 11.61 m for the spent fuel pool. In this study, there are
three TRACE/SNAP models: one-channel, two-channel, and
multi-channel TRACE/SNAP model. Additionally, the cooling system
failure of the spent fuel pool was simulated and analyzed by using the
above models. According to the analysis results, the peak cladding
temperature response was more accurate in the multi-channel
TRACE/SNAP model. The results depicted that the uncovered of the
fuels occurred at 2.7 day after the cooling system failed. In order to
estimate the detailed fuel rods performance, FRAPTRAN code was
used in this research. According to the results of FRAPTRAN, the
highest cladding temperature located on the node 21 of the fuel rod
(the highest node at node 23) and the cladding burst roughly after 3.7
day.
Abstract: Similar to economies in many countries; family-owned enterprises have a significant role in the development of Turkish economy. Although they have a large share in economic terms, their lifetime is limited to working life of their founders. Failure in achieving their sustainability deeply affects not only these businesses but also the economy. Therefore, two basic elements of family owned enterprises, family and organizational culture and especially entrepreneurship culture, should be examined closely. The degree of effectiveness of parents in instilling their children with entrepreneurship culture and their effects on children's profession choices are examined through face-to-face surveys with the managers owning family businesses randomly chosen among family-owned enterprises registered in Konya Chamber of Industry, which are active in specific sectors and which had different generations in their management.
Abstract: In addition to the fact that mental health bears great significance to a particular individual, it can also be regarded as an organizational, community and societal resource. Within the Szeged Health Promotion Research Group, we conducted mental health surveys on two levels: The inhabitants of a medium-sized Hungarian town and students of a Hungarian university with a relatively big headcount were requested to participate in surveys whose goals were to define local government priorities and organization-level health promotion programmes, respectively. To facilitate professional decision-making, we defined three, pragmatically relevant, groups of the target population: the mentally healthy, the vulnerable and the endangered. In order to determine which group a person actually belongs to, we designed a simple and quick measurement tool, which could even be utilised as a smoothing method, the Mental State Questionnaire validity of the above three categories was verified by analysis of variance against psychological quality of life variables. We demonstrate the pragmatic significance of our method via the analyses of the scores of our two mental health surveys. On town level, during our representative survey in Hódmezővásárhely (N=1839), we found that 38.7% of the participants was mentally healthy, 35.3% was vulnerable, while 16.3% was considered as endangered. We were able to identify groups that were in a dramatic state in terms of mental health. For example, such a group consisted of men aged 45 to 64 with only primary education qualification and the ratios of the mentally healthy, vulnerable and endangered were 4.5, 45.5 and 50%, respectively. It was also astonishing to see to what a little extent qualification prevailed as a protective factor in the case of women. Based on our data, the female group aged 18 to 44 with primary education—of whom 20.3% was mentally healthy, 42.4% vulnerable and 37.3% was endangered—as well as the female group aged 45 to 64 with university or college degree—of whom 25% was mentally healthy, 51.3 vulnerable and 23.8% endangered—are to be handled as priority intervention target groups in a similarly difficult position. On organizational level, our survey involving the students of the University of Szeged, N=1565, provided data to prepare a strategy of mental health promotion for a university with a headcount exceeding 20,000. When developing an organizational strategy, it was important to gather information to estimate the proportions of target groups in which mental health promotion methods; for example, life management skills development, detection, psychological consultancy, psychotherapy, would be applied. Our scores show that 46.8% of the student participants were mentally healthy, 42.1% were vulnerable and 11.1% were endangered. These data convey relevant information as to the allocation of organizational resources within a university with a considerable headcount. In conclusion, The Mental State Questionnaire, as a valid smoothing method, is adequate to describe a community in a plain and informative way in the terms of mental health. The application of the method can promote the preparation, design and implementation of mental health promotion interventions.
Abstract: This research investigates the impact of Brand Loyalty on the product performance and the factors those are considered more important in brand reputation. Variables selected for this research are Brand quality, Brand Equity, Brand Reputation to explore the impact of these variables on Product performance. For this purpose, primary research has been conducted. The questionnaire survey for this research study was administered among the population mainly at the shopping malls. For this research study, a sample size of 250 respondents has been taken into consideration. Customers from the shopping malls and university students constitute the sample for this research study using random sampling (non-probabilistic) used as a sampling technique for conducting the research survey. According to the results obtained from the collected data, it is interpreted that product performance shares a direct relationship with brand quality, brand quality, and brand reputation. Result also showed that brand quality and brand equity has a significant effect on product performance, whereas brand reputation has an insignificant effect on product performance.
Abstract: Retinoblastoma is a rare type of childhood genetic cancer that affects children worldwide. The diagnosis is often missed due to lack of education and difficulty in presentation of the tumor. Frequently, the tumor on the retina is noticed by photography when the red-eye flash, commonly seen in normal eyes, is not produced. Instead, a yellow or white colored patch is seen or the child has a noticeable strabismus. Early detection can be life-saving though often results in removal of the affected eye. Remaining functioning in the healthy eye when the child is young has resulted in super-vision and high or above-average intelligence. Technological advancement of cameras has helped in early detection. Brain imaging has also made possible early detection of neurological diseases and, together with the monitoring of cortisol levels and yawning frequency, promises to be the next new early diagnostic tool for the detection of neurological diseases where cortisol insufficiency is particularly salient, such as multiple sclerosis and Cushing’s disease.