Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: The Haussmannization plan of Cairo in 1867 formed a
regular network of roundabout spaces, though deteriorated at present.
The method of identifying the spatial structure of roundabout Cairo
for conservation matches the voronoi diagram with the space syntax
through their geometrical property of spatial convexity. In this
initiative, the primary convex hull of first-order voronoi adopts the
integral and control measurements of space syntax on Cairo’s
roundabout generators. The functional essence of royal palaces
optimizes the roundabout structure in terms of spatial measurements
and the symbolic voronoi projection of 'Tahrir Roundabout' over the
Giza Nile and Pyramids. Some roundabouts of major public and
commercial landmarks surround the pole of 'Ezbekia Garden' with a
higher control than integral measurements, which filter the new
spatial structure from the adjacent traditional town. Nevertheless, the
least integral and control measures correspond to the voronoi
contents of pollutant workshops and the plateau of old Cairo Citadel
with the visual compensation of new royal landmarks on top.
Meanwhile, the extended suburbs of infinite voronoi polygons
arrange high control generators of chateaux housing in 'garden city'
environs. The point pattern of roundabouts determines the
geometrical characteristics of voronoi polygons. The measured
lengths of voronoi edges alternate between the zoned short range at
the new poles of Cairo and the distributed structure of longer range.
Nevertheless, the shortest range of generator-vertex geometry
concentrates at 'Ezbekia Garden' where the crossways of vast Cairo
intersect, which maximizes the variety of choice at different spatial
resolutions. However, the symbolic 'Hippodrome' which is the largest
public landmark forms exclusive geometrical measurements, while
structuring a most integrative roundabout to parallel the royal syntax.
Overview of the symbolic convex hull of voronoi with space syntax
interconnects Parisian Cairo with the spatial chronology of scattered
monuments to conceive one universal Cairo structure. Accordingly,
the approached methodology of 'voronoi-syntax' prospects the future
conservation of roundabout Cairo at the inferred city-level concept.
Abstract: Coal fly ash, an industrial by product of coal
combustion thermal power plants is considered as a hazardous
material and its improper disposal has become an environmental
issue. On the other hand, manufacturing conventional clay bricks
involves on consumption of large amount of clay and leads
substantial depletion of topsoil. This paper unveils the possibility of
using fly ash as a partial replacement of clay for brick manufacturing
considering the local technology practiced in Bangladesh. The effect
of fly ash with different replacing ratio (0%, 20%, 30%, 40%, and
50% by volume) of clay on properties of bricks was studied. Bricks
were made in the field parallel to ordinary bricks marked with
specific number for different percentage to identify them at time of
testing. No physical distortion is observed in fly ash brick after
burning in the kiln. Results from laboratory test show that
compressive strength of brick is decreased with the increase of fly
ash and maximum compressive strength is found to be 19.6 MPa at
20% of fly ash. In addition, water absorption of fly ash brick is
increased with the increase of fly ash. The abrasion value and
Specific gravity of coarse aggregate prepared from brick with fly ash
also studied and the results of this study suggests that 20% fly ash
can be considered as the optimum fly ash content for producing good
quality bricks utilizing present practiced technology.
Abstract: Agricultural machinery industry plays an important
role in the industrial development especially the production industry
of the country. There has been continuing development responding to
the higher demand of the production. However, the problem in
agricultural machinery production still exists. Thus, the purpose of
this research is to investigate problems on fundamental factors of
industry based on the entrepreneurs’ point of view. The focus was on
the small and medium size industry receiving factory license type
number 0660 from the Department of Industrial Works. The
investigation was on the comparison between the management of the
small and medium size agricultural industry in 3 provinces in the
central region of Thailand. Population in this study consisted of 189
company managers or managing directors, of which 101 were from
the small size and 88 were from the medium size industry. The data
were analyzed to find percentage, arithmetic mean, and standard
deviation with independent sample T-test at the statistical
significance .05. The results showed that the small and medium size
agricultural machinery manufacturers in the central region of
Thailand reported high problems in every aspect. When compared the
problems on basic factors in running the business, it was found that
there was no statistically difference at .05 in managing of the small
and medium size agricultural machinery manufacturers. However,
there was a statistically significant difference between the small and
medium size agricultural machinery manufacturers on the aspect of
policy and services of the government. The problems reported by the
small and medium size agricultural machinery manufacturers were
the services on public tap water and the problem on politic and
stability of the country.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p
Abstract: We regard forecasting of energy consumption by
private production areas of a large industrial facility as well as by the
facility itself. As for production areas, the forecast is made based on
empirical dependencies of the specific energy consumption and the
production output. As for the facility itself, implementation of the
task to minimize the energy consumption forecasting error is based
on adjustment of the facility’s actual energy consumption values
evaluated with the metering device and the total design energy
consumption of separate production areas of the facility. The
suggested procedure of optimal energy consumption was tested based
on the actual data of core product output and energy consumption by
a group of workshops and power plants of the large iron and steel
facility. Test results show that implementation of this procedure gives
the mean accuracy of energy consumption forecasting for winter
2014 of 0.11% for the group of workshops and 0.137% for the power
plants.
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: We have studied the temporal characteristics of
bistable perception of the stimuli of two types: one involves
alterations in a perceived depth and another one has an ambiguous
content. We used the Necker lattice and lines of shadowed circles
ambiguously perceived either as spheres or holes as stimuli of the
first type. The Winson figure (the Eskimo/Indian picture) was a
stimulus of the second type. We have analyzed how often the
reversals occurred (reversal rate) and for how long each of the two
interpretations, or percepts, was observed during one presentation
(stability durations). For all three ambiguous images the reversal rate
and the stability durations had similar values, which provide another
evidence for a significant role of top-down processes in multistable
perception.
Abstract: Global economy today is full of sophistication. All
over the world, business and marketing practices are undergoing
unprecedented transformation. In realization of this fact, the federal
government of Nigeria has put in place a robust transformation
agenda in order to put Nigeria in a better position to be a competitive
player and in the process transform all sectors of its economy. New
technologies, especially the Internet, are the driving force behind this
transformation. However, technology has inadvertently affected the
way businesses are done thus necessitating the acquisition of new
skills. In developing countries like Nigeria, citizens are still battling
with effective application of those technologies. Obviously, students
of business education need to acquire relevant business knowledge to
be able to transit into the world of work on graduation from school
and compete favorably in the labor market. Therefore, effective
utilization of social media by both teachers and students can help
extensively in empowering students with the needed skills. Social
media which is a group of Internet-based applications built on the
ideological foundations of Web 2.0, that allow the creation and
exchange of user generated content, and if incorporated into the
classroom experience may be the needed answer to unemployment
and poverty in Nigeria as beneficiaries can easily connect with
existing and potential enterprises and customers, engage with them
and reinforce mutual business benefits. Challenges and benefits of
social media use in education in Nigeria universities were revealed in
this study.
Abstract: The underutilization of biomass resources in the
Philippines, combined with its growing population and the rise in
fossil fuel prices confirms demand for alternative energy sources. The
goal of this paper is to provide a comparison of MODIS-based and
Landsat-based agricultural land cover maps when used in the
estimation of rice hull’s available energy potential. Biomass resource
assessment was done using mathematical models and remote sensing
techniques employed in a GIS platform.
Abstract: This research aimed to investigate the relationship
between attitude towards marketing mix, brand image and consumer
behavior of the passengers of low-cost airlines service. This study
employed by quantitative research and the questionnaire was used to
collect the data from 400 sampled of the passengers who have ever
used the low-cost airline services based in Bangkok, Thailand. The
descriptive statistics and Pearson’s correlation analysis were used to
analyze data. The research results revealed that the attitude of the marketing mix
of the low-cost airline services including product, price, place,
promotion and process had related to the consumer behavior on the
aspects of duration of service and frequency of service. While, the
brand image of the low cost airline including the characteristics of
organization, service quality and company identity had related to the
consumer behavior on duration of service, frequency of service and
cost of service at the significant statistically acceptable levels.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: With the increasing dependence of countries on the
critical infrastructure, it increases their vulnerability. Big threat is
primarily in the human factor (personnel of the critical infrastructure)
and in terrorist attacks. It emphasizes the development of
methodology for searching of weak points and their subsequent
elimination. This article discusses methods for the analysis of safety
in the objects of critical infrastructure. It also contains proposal for
methodology for training employees of security services in the
objects of the critical infrastructure and developing scenarios of
attacks on selected objects of the critical infrastructure.
Abstract: In the Solid-State-Drive (SSD) performance, whether
the data has been well parallelized is an important factor. SSD
parallelization is affected by allocation scheme and it is directly
connected to SSD performance. There are dynamic allocation and
static allocation in representative allocation schemes. Dynamic
allocation is more adaptive in exploiting write operation parallelism,
while static allocation is better in read operation parallelism.
Therefore, it is hard to select the appropriate allocation scheme when
the workload is mixed read and write operations. We simulated
conditions on a few mixed data patterns and analyzed the results to
help the right choice for better performance. As the results, if data
arrival interval is long enough prior operations to be finished and
continuous read intensive data environment static allocation is more
suitable. Dynamic allocation performs the best on write performance
and random data patterns.
Abstract: The application of ESS (Energy Storage Systems) in
the future grids has been the solution of the microgrid. However, high
investment costs necessitate accurate modeling and control strategy of
ESS to justify its economic viability and further underutilization.
Therefore, the reasonable control strategy for ESS which is subjected
to generator and usage helps to curtail the cost of investment and
operation costs. The rated frequency in power system is decreased
when the load is increasing unexpectedly; hence the thermal power is
operated at the capacity of only its 95% for the Governor Free (GF) to
adjust the frequency as reserve (5%) in practice. The ESS can be
utilized with governor at the same time for the frequency response due
to characteristic of its fast response speed and moreover, the cost of
ESS is declined rapidly to the reasonable price. This paper presents the
ESS control strategy to extend usage of the ESS taken account into
governor’s ramp rate and reduce the governor’s intervention as well.
All results in this paper are simulated by MATLAB.
Abstract: To maintain a healthy balanced loyalty, whether to art
or society, posits a debatable issue. The artist is always on the look
out for the potential tension between those two realms. Therefore,
one of the most painful dilemmas the artist finds is how to function in
a society without sacrificing the aesthetic values of his/her work. In
other words, the life-long awareness of failure which derives from the
concept of the artist as caught between unflattering social realities
and the need to invent genuine art forms becomes a fertilizing soil for
the artists to be tackled. Thus, within the framework of this dilemma,
the question of the responsibility of the artist and the relationship of
the art to politics will be illuminating. To a larger extent, however, in
drama, this dilemma is represented by the fictional characters of the
play. The present paper tackles the idea of the amorality of the artist in
selected plays by Tom Stoppard. However, Stoppard’s awareness of
his situation as a refugee has led him to keep at a distance from
politics. He tried hard to avoid any intervention into the realms of
political debate, especially in his earliest work. On the one hand, it is
not meant that he did not interest in politics as such, but rather he
preferred to question it than to create a fixed ideological position. On
the other hand, Stoppard’s refusal to intervene in politics is ascribed
to his feeling of gratitude to Britain where he settled. As a result,
Stoppard has frequently been criticized for a lack of political
engagement and also for not leaning too much for the left when he
does engage. His reaction to these public criticisms finds expression
in his self-conscious statements which defensively stressed the
artifice of his work. He, like Oscar Wilde thinks that the
responsibility of the artist is devoted to the realm of his/her art.
Consequently, his consciousness for the role of the artist is truly
reflected in his two plays, Artist Descending a Staircase (1972) and
Travesties (1974).
Abstract: In this paper, we calculate the two-photon ionization
(TPI) cross-section for pump-probe scheme in Ag neutral cluster. The
pump photon energy is assumed to be close to the surface plasmon
(SP) energy of cluster in dielectric media. Due to this choice, the
pump wave excites collective oscillations of electrons-SP and the
probe wave causes ionization of the cluster. Since the interband
transition energy in Ag exceeds the SP resonance energy, the main
contribution into the TPI comes from the latter. The advantage of Ag
clusters as compared to the other noble metals is that the SP
resonance in silver cluster is much sharper because of peculiarities of
its dielectric function. The calculations are performed by separating
the coordinates of electrons corresponding to the collective
oscillations and the individual motion that allows taking into account
the resonance contribution of excited SP oscillations. It is shown that
the ionization cross section increases by two orders of magnitude if
the energy of the pump photon matches the surface plasmon energy
in the cluster.
Abstract: Liver segmentation from medical images poses more
challenges than analogous segmentations of other organs. This
contribution introduces a liver segmentation method from a series of
computer tomography images. Overall, we present a novel method for
segmenting liver by coupling density matching with shape priors.
Density matching signifies a tracking method which operates via
maximizing the Bhattacharyya similarity measure between the
photometric distribution from an estimated image region and a model
photometric distribution. Density matching controls the direction of
the evolution process and slows down the evolving contour in regions
with weak edges. The shape prior improves the robustness of density
matching and discourages the evolving contour from exceeding liver’s
boundaries at regions with weak boundaries. The model is
implemented using a modified distance regularized level set (DRLS)
model. The experimental results show that the method achieves a
satisfactory result. By comparing with the original DRLS model, it is
evident that the proposed model herein is more effective in addressing
the over segmentation problem. Finally, we gauge our performance of
our model against matrices comprising of accuracy, sensitivity, and
specificity.