Abstract: A study was undertaken to assess the potential of an
Algal Turf Scrubber to remove nitrogen from aquaculture effluent to
reduce environmental pollution. High total ammonia nitrogen
concentrations were introduced to an Algal Turf Scrubber developed
under varying hydraulic surface loading rates of African catfish
(Clarius gariepinus) effluent in a recirculating aquaculture system.
Nutrient removal rates were not affected at total suspended solids
concentration of up to 0.04g TSS/l (P > 0.05). Nitrogen removal
rates 0.93-0.99g TAN/m²/d were recorded at very high loading rates
3.76-3.81 g TAN/m²/d. Total ammonia removal showed ½ order
kinetics between 1.6 to 2.3mg/l Total Ammonia Nitrogen
concentrations. Nitrogen removal increased with its loading, which
increased with hydraulic surface loading rate. Total Ammonia
Nitrogen removal by Algal turf scrubber was higher than reported
values for fluidized bed filters and trickling filters. The algal turf
scrubber also effectively removed nitrate thereby reducing the need
for water exchange.
Abstract: In a world worried about water resources with the
shadow of drought and famine looming all around, the quality of
water is as important as its quantity. The source of all concerns is the
constant reduction of per capita quality water for different uses.
Iran With an average annual precipitation of 250 mm compared to
the 800 mm world average, Iran is considered a water scarce country
and the disparity in the rainfall distribution, the limitations of
renewable resources and the population concentration in the margins
of desert and water scarce areas have intensified the problem.
The shortage of per capita renewable freshwater and its poor
quality in large areas of the country, which have saline, brackish or
hard water resources, and the profusion of natural and artificial
pollutant have caused the deterioration of water quality.
Among methods of treatment and use of these waters one can refer
to the application of membrane technologies, which have come into
focus in recent years due to their great advantages. This process is
quite efficient in eliminating multi-capacity ions; and due to the
possibilities of production at different capacities, application as
treatment process in points of use, and the need for less energy in
comparison to Reverse Osmosis processes, it can revolutionize the
water and wastewater sector in years to come. The article studied the
different capacities of water resources in the Persian Gulf and Oman
Sea watershed basins, and processes the possibility of using
nanofiltration process to treat brackish and non-conventional waters
in these basins.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: The design requirements for successful human
accommodation in urban spaces are well known; and the range of
facilities available for meeting urban water quality and quantity
requirements is also well established. Their competing requirements
must be reconciled in order for urban spaces to be successful for
both. This paper outlines the separate human and water imperatives
and their interactions in urban spaces. Stormwater management
facilities- relative potential contributions to urban spaces are
contrasted, and design choices for achieving those potentials are
described. This study uses human success of urban space as the
evaluative criterion of stormwater amenity: human values call on
stormwater facilities to contribute to successful human spaces.
Placing water-s contribution under the overall idea of successful
urban space is an evolution from previous subjective evaluations.
The information is based on photographs and notes from
approximately 1,000 stormwater facilities and urban sites collected
during the last 35 years in North America and overseas, and the
author-s experience on multi-disciplinary design teams. This
conceptual study combines the disciplinary roles of engineering,
landscape architecture, and sociology in effecting successful urban
design.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: In recent years, many researches to mine the exploding Web world, especially User Generated Content (UGC) such as
weblogs, for knowledge about various phenomena and events in the physical world have been done actively, and also Web services
with the Web-mined knowledge have begun to be developed for
the public. However, there are few detailed investigations on how accurately Web-mined data reflect physical-world data. It must be
problematic to idolatrously utilize the Web-mined data in public Web services without ensuring their accuracy sufficiently. Therefore,
this paper introduces the simplest Web Sensor and spatiotemporallynormalized
Web Sensor to extract spatiotemporal data about a target
phenomenon from weblogs searched by keyword(s) representing the
target phenomenon, and tries to validate the potential and reliability of the Web-sensed spatiotemporal data by four kinds of granularity
analyses of coefficient correlation with temperature, rainfall, snowfall,
and earthquake statistics per day by region of Japan Meteorological
Agency as physical-world data: spatial granularity (region-s population
density), temporal granularity (time period, e.g., per day vs. per week), representation granularity (e.g., “rain" vs. “heavy rain"), and
media granularity (weblogs vs. microblogs such as Tweets).
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.
Abstract: This paper proposes a new approach to offer a private
cloud service in HPC clusters. In particular, our approach relies on
automatically scheduling users- customized environment request as a
normal job in batch system. After finishing virtualization request jobs,
those guest operating systems will dismiss so that compute nodes will
be released again for computing. We present initial work on the
innovative integration of HPC batch system and virtualization tools
that aims at coexistence such that they suffice for meeting the
minimizing interference required by a traditional HPC cluster. Given
the design of initial infrastructure, the proposed effort has the potential
to positively impact on synergy model. The results from the
experiment concluded that goal for provisioning customized cluster
environment indeed can be fulfilled by using virtual machines, and
efficiency can be improved with proper setup and arrangements.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: The study of tourist activities and the mapping of their routes in space and time has become an important issue in tourism management. Here we represent space-time paths for the tourism industry by visualizing individual tourist activities and the paths followed using a 3D Geographic Information System (GIS). Considerable attention has been devoted to the measurement of accessibility to shopping, eating, walking and other services at the tourist destination. I turns out that GIS is a useful tool for studying the spatial behaviors of tourists in the area. The value of GIS is especially advantageous for space-time potential path area measures, especially for the accurate visualization of possible paths through existing city road networks. This study seeks to apply space-time concepts with a detailed street network map obtained from Google Maps to measure tourist paths both spatially and temporally. These paths are further determined based on data obtained from map questionnaires regarding the trip activities of 40 individuals. The analysis of the data makes it possible to determining the locations of the more popular paths. The results can be visualized using 3D GIS to show the areas and potential activity opportunities accessible to tourists during their travel time.
Abstract: This paper presents an effective traffic lights
recognition method at the daytime. First, Potential Traffic Lights
Detector (PTLD) use whole color source of YCbCr channel image and
make each binary image of green and red traffic lights. After PTLD
step, Shape Filter (SF) use to remove noise such as traffic sign, street
tree, vehicle, and building. At this time, noise removal properties
consist of information of blobs of binary image; length, area, area of
boundary box, etc. Finally, after an intermediate association step witch
goal is to define relevant candidates region from the previously
detected traffic lights, Adaptive Multi-class Classifier (AMC) is
executed. The classification method uses Haar-like feature and
Adaboost algorithm. For simulation, we are implemented through Intel
Core CPU with 2.80 GHz and 4 GB RAM and tested in the urban and
rural roads. Through the test, we are compared with our method and
standard object-recognition learning processes and proved that it
reached up to 94 % of detection rate which is better than the results
achieved with cascade classifiers. Computation time of our proposed
method is 15 ms.
Abstract: With the advent of emerging personal computing paradigms such as ubiquitous and mobile computing, Web contents are becoming accessible from a wide range of mobile devices. Since these devices do not have the same rendering capabilities, Web contents need to be adapted for transparent access from a variety of client agents. Such content adaptation is exploited for either an individual element or a set of consecutive elements in a Web document and results in better rendering and faster delivery to the client device. Nevertheless, Web content adaptation sets new challenges for semantic markup. This paper presents an advanced components platform, called SMC, enabling the development of mobility applications and services according to a channel model based on the principles of Services Oriented Architecture (SOA). It then goes on to describe the potential for integration with the Semantic Web through a novel framework of external semantic annotation that prescribes a scheme for representing semantic markup files and a way of associating Web documents with these external annotations. The role of semantic annotation in this framework is to describe the contents of individual documents themselves, assuring the preservation of the semantics during the process of adapting content rendering. Semantic Web content adaptation is a way of adding value to Web contents and facilitates repurposing of Web contents (enhanced browsing, Web Services location and access, etc).
Abstract: The ability of UML to handle the modeling process of complex industrial software applications has increased its popularity to the extent of becoming the de-facto language in serving the design purpose. Although, its rich graphical notation naturally oriented towards the object-oriented concept, facilitates the understandability, it hardly successes to report all domainspecific aspects in a satisfactory way. OCL, as the standard language for expressing additional constraints on UML models, has great potential to help improve expressiveness. Unfortunately, it suffers from a weak formalism due to its poor semantic resulting in many obstacles towards the build of tools support and thus its application in the industry field. For this reason, many researches were established to formalize OCL expressions using a more rigorous approach. Our contribution join this work in a complementary way since it focuses specifically on OCL predefined properties which constitute an important part in the construction of OCL expressions. Using formal methods, we mainly succeed in expressing rigorously OCL predefined functions.
Abstract: Results in one field necessarily give insight into the
others, and all have much potential for scientific and technological
application. The Hadamard-transform technique once been applied to
the spectrometry also has its use in the SNR Enhancement of OTDR.
In this report, a new set of code (Simplex-codes) is discussed and
where the addition gain of SNR come from is implied.
Abstract: This paper reviews the objectives, methods and results of previous studies on biodrying of solid waste in several countries. Biodrying of solid waste is a novel technology in developing countries such as in Malaysia where high moisture content in organic waste makes the segregation process for recycling purposes complicated and diminishes the calorific value for the use of fuel source. In addition, the high moisture content also encourages the breeding of vectors and disease-bearing animals. From the laboratory results, the average moisture content of organic waste, paper, plastics and metals are 58.17%, 37.93%, 29.79% and 1.03% respectively for UKM campus. Biodrying of solid waste is a simple method of waste treatment as well as a cost-efficient technology to dry the solid waste. The process depends on temperature monitoring and air flow control along with the natural biodegradable process of organic waste. This review shows that the biodrying of solid waste method has high potential in treatment and recycling of solid waste, be useful for biodrying study and implementation in Malaysia.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: The objective of this paper is to construct a creativity
composite index designed to capture the growing role of creativity in
driving economic and social development for the 27 European Union
countries.
The paper proposes a new approach for the measurement of EU-27
creative potential and for determining its capacity to attract and
develop creative human capital. We apply a modified version of the
3T model developed by Richard Florida and Irene Tinagli for
constructing a Euro-Creativity Index. The resulting indexes establish
a quantitative base for policy makers, supporting their efforts to
determine the contribution of creativity to economic development.