Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: Analyzing DNA microarray data sets is a great
challenge, which faces the bioinformaticians due to the complication
of using statistical and machine learning techniques. The challenge
will be doubled if the microarray data sets contain missing data,
which happens regularly because these techniques cannot deal with
missing data. One of the most important data analysis process on
the microarray data set is feature selection. This process finds the
most important genes that affect certain disease. In this paper, we
introduce a technique for imputing the missing data in microarray
data sets while performing feature selection.
Abstract: In this letter, we explore exact solutions for the
Horava-Lifshitz gravity. We use of an extension of this theory with
first order dynamical lapse function. The equations of motion have
been derived in a fully consistent scenario. We assume that there
are some spherically symmetric families of exact solutions of this
extended theory of gravity. We obtain exact solutions and investigate
the singularity structures of these solutions. Specially, an exact
solution with the regular horizon is found.
Abstract: An attempt has been made in the present
communication to elucidate the efficacy of robust ANOVA methods
to analyse horticultural field experimental data in the presence of
outliers. Results obtained fortify the use of robust ANOVA methods
as there was substantiate reduction in error mean square, and hence
the probability of committing Type I error, as compared to the regular
approach.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: The thyroid gland is the largest classic endocrine
organ that effects many organs of the body and plays a significant
role in the process of Metabolism in animals. The aim of this study
was to investigate the prevalence of thyroid disorders diagnosed by
ultrasound and microscopic Lesions of the thyroid during the
slaughter of apparently healthy One Humped Camels (Camelus
dromedarius) in Iran. Randomly, 520 male camels (With an age
range of 4 to 8 years), were studied in 2012 to 2013. The Camels’
thyroid glands were evaluated by sonographic examination. In both
longitudinal and transverse view and then tissue sections were
provide and stained with H & E and finally examined by light
microscopy. The results obtained indicated the following:
hyperplastic goiter (21%), degenerative changes (12%), follicular
cysts (8%), follicular atrophy (4%), nodular hyperplasia (3%),
adenoma (1%), carcinoma (1%) and simple goiter colloid (1%).
Ultrasound evaluation of thyroid gland in adenoma and carcinoma
showed enlargement and irregular of the gland, decreased
echogenicity, and the heterogeneous thyroid parenchyma. Also, in
follicular cysts were observed in the enlarged gland with no echo
structures of different sizes and decreased echogenicity as a local or
general. In nodular hyperplasia, increase echogenicity and
heterogeneous parenchymal were seen. These findings suggest the
use of sonography and pathology as a screening test in the diagnosis
of complications of thyroid disorders.
Abstract: Given a graph G. A cycle of G is a sequence of
vertices of G such that the first and the last vertices are the same.
A hamiltonian cycle of G is a cycle containing all vertices of G.
The graph G is k-ordered (resp. k-ordered hamiltonian) if for any
sequence of k distinct vertices of G, there exists a cycle (resp.
hamiltonian cycle) in G containing these k vertices in the specified
order. Obviously, any cycle in a graph is 1-ordered, 2-ordered and 3-
ordered. Thus the study of any graph being k-ordered (resp. k-ordered
hamiltonian) always starts with k = 4. Most studies about this topic
work on graphs with no real applications. To our knowledge, the
chordal ring families were the first one utilized as the underlying
topology in interconnection networks and shown to be 4-ordered.
Furthermore, based on our computer experimental results, it was
conjectured that some of them are 4-ordered hamiltonian. In this
paper, we intend to give some possible directions in proving the
conjecture.
Abstract: The Simulation based VLSI Implementation of
FELICS (Fast Efficient Lossless Image Compression System)
Algorithm is proposed to provide the lossless image compression and
is implemented in simulation oriented VLSI (Very Large Scale
Integrated). To analysis the performance of Lossless image
compression and to reduce the image without losing image quality
and then implemented in VLSI based FELICS algorithm. In FELICS
algorithm, which consists of simplified adjusted binary code for
Image compression and these compression image is converted in
pixel and then implemented in VLSI domain. This parameter is used
to achieve high processing speed and minimize the area and power.
The simplified adjusted binary code reduces the number of arithmetic
operation and achieved high processing speed. The color difference
preprocessing is also proposed to improve coding efficiency with
simple arithmetic operation. Although VLSI based FELICS
Algorithm provides effective solution for hardware architecture
design for regular pipelining data flow parallelism with four stages.
With two level parallelisms, consecutive pixels can be classified into
even and odd samples and the individual hardware engine is
dedicated for each one. This method can be further enhanced by
multilevel parallelisms.
Abstract: Background: Taiwan now is an aging society. Research
on the elderly should not be confined to caring for seniors, but should
also be focused on ways to improve health and the quality of life.
Senior citizens who participate in volunteer services could become
less lonely, have new growth opportunities, and regain a sense of
accomplishment. Thus, the question of how to get the elderly to
participate in volunteer service is worth exploring. Objective: Apply
the Transtheoretical Model to understand stages of change in regular
volunteer service and voluntary service behaviour among the seniors.
Methods: 1525 adults over the age of 65 from the Renai district of
Keelung City were interviewed. The research tool was a
self-constructed questionnaire, and individual interviews were
conducted to collect data. Then the data was processed and analyzed
using the IBM SPSS Statistics 20 (Windows version) statistical
software program. Results: In the past six months, research subjects
averaged 9.92 days of volunteer services. A majority of these elderly
individuals had no intention to change their regular volunteer services.
We discovered that during the maintenance stage, the self-efficacy for
volunteer services was higher than during all other stages, but
self-perceived barriers were less during the preparation stage and
action stage. Self-perceived benefits were found to have an important
predictive power for those with regular volunteer service behaviors in
the previous stage, and self-efficacy was found to have an important
predictive power for those with regular volunteer service behaviors in
later stages. Conclusions/Implications for Practice: The research
results support the conclusion that community nursing staff should
group elders based on their regular volunteer services change stages
and design appropriate behavioral change strategies.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: This paper describes a logical method to enhance
security on the grid computing to restrict the misuse of the grid
resources. This method is an economic and efficient one to avoid the
usage of the special devices. The security issues, techniques and
solutions needed to provide a secure grid computing environment are
described. A well defined process for security management among
the resource accesses and key holding algorithm is also proposed. In
this method, the identity management, access control and
authorization and authentication are effectively handled.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: Pavement surface unevenness plays a pivotal role on
roughness index of road which affects on riding comfort ability.
Comfort ability refers to the degree of protection offered to vehicle
occupants from uneven elements in the road surface. So, it is
preferable to have a lower roughness index value for a better riding
quality of road users. Roughness is generally defined as an
expression of irregularities in the pavement surface which can be
measured using different equipments like MERLIN, Bump integrator,
Profilometer etc. Among them Bump Integrator is quite simple and
less time consuming in case of long road sections. A case study is
conducted on low volume roads in West District in Tripura to
determine roughness index (RI) using Bump Integrator at the
standard speed of 32 km/h. But it becomes too tough to maintain the
requisite standard speed throughout the road section. The speed of
Bump Integrator (BI) has to lower or higher in some distinctive
situations. So, it becomes necessary to convert these roughness index
values of other speeds to the standard speed of 32 km/h. This paper
highlights on that roughness index conversional model. Using SPSS
(Statistical Package of Social Sciences) software a generalized
equation is derived among the RI value at standard speed of 32 km/h
and RI value at other speed conditions.
Abstract: The Port of Townsville conducts regular annual
maintenance dredging to maintain depths of its harbor basin and
approach channels for the navigational safety of the vessels against
the natural accumulation of marine sediments. In addition to the
regular maintenance dredging, the port undertakes emergency
dredging in cases where large quantities of sediments are mobilized
and deposited in port waters by cyclone or major flood events. The
maintenance dredging material derived from the port may be
disposed at sea or on land in accordance with relevant state and
commonwealth regulations. For the land disposal, the dredged mud
slurry is hydraulically placed into containment ponds and left to
undergo sedimentation and self-weight consolidation to form fill
material for land reclamation. This paper provides an overview of the
maintenance dredging at the Port of Townsville and emphasis on
maintenance dredging requirements, sediment quality, bathymetry,
dredging methods used, and dredged material disposal options.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: This paper aims at introducing finite automata theory,
the different ways to describe regular languages and create a program
to implement the subset construction algorithms to convert
nondeterministic finite automata (NFA) to deterministic finite
automata (DFA). This program is written in c++ programming
language. The program reads FA 5tuples from text file and then
classifies it into either DFA or NFA. For DFA, the program will read
the string w and decide whether it is acceptable or not. If accepted, the
program will save the tracking path and point it out. On the other hand,
when the automation is NFA, the program will change the Automation
to DFA so that it is easy to track and it can decide whether the w exists
in the regular language or not.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.