Abstract: The analytical bright two soliton solution of the 3-
coupled nonlinear Schrödinger equations with variable coefficients in
birefringent optical fiber is obtained by Darboux transformation
method. To the design of ultra-speed optical devices, Soliton
interaction and control in birefringence fiber is investigated. Lax pair
is constructed for N coupled NLS system through AKNS method.
Using two-soliton solution, we demonstrate different interaction
behaviors of solitons in birefringent fiber depending on the choice of
control parameters. Our results shows that interactions of optical
solitons have some specific applications such as construction of logic
gates, optical computing, soliton switching, and soliton amplification
in wavelength division multiplexing (WDM) system.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Background: To compare the thinning patterns of the
ganglion cell-inner plexiform layer (GCIPL) and peripapillary retinal
nerve fiber layer (pRNFL) as measured using Cirrus high-definition
optical coherence tomography (HD-OCT) in patients with visual field
(VF) defects that respect the vertical meridian. Methods: Twenty eyes of eleven patients with VF defects that
respect the vertical meridian were enrolled retrospectively. The
thicknesses of the macular GCIPL and pRNFL were measured using
Cirrus HD-OCT. The 5% and 1% thinning area index (TAI) was
calculated as the proportion of abnormally thin sectors at the 5% and
1% probability level within the area corresponding to the affected VF.
The 5% and 1% TAI were compared between the GCIPL and pRNFL
measurements. Results: The color-coded GCIPL deviation map showed a
characteristic vertical thinning pattern of the GCIPL, which is also
seen in the VF of patients with brain lesions. The 5% and 1% TAI
were significantly higher in the GCIPL measurements than in the
pRNFL measurements (all P < 0.01). Conclusions: Macular GCIPL analysis clearly visualized a
characteristic topographic pattern of retinal ganglion cell (RGC) loss
in patients with VF defects that respect the vertical meridian, unlike
pRNFL measurements. Macular GCIPL measurements provide more
valuable information than pRNFL measurements for detecting the
loss of RGCs in patients with retrograde degeneration of the optic
nerve fibers.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: This paper reports on the response of a fiber-optic
sensing probe to small concentrations of hydrogen peroxide (H2O2)
vapor at room temperature. H2O2 has extensive applications in industrial and medical
environments. Conversely, H2O2 can be a health hazard by itself. For
example, H2O2 induces cellular damage in human cells and its
presence can be used to diagnose illnesses such as asthma and human
breast cancer. Hence, development of reliable H2O2 sensor is of vital
importance to detect and measure this species. Ferric ferrocyanide, referred to as Prussian Blue (PB), was
deposited on the tip of a multimode optical fiber through the single
source precursor technique and served as an indicator of H2O2 in a
spectroscopic manner. Sensing tests were performed in H2O2-H2O
vapor mixtures with different concentrations of H2O2. The results of sensing tests show the sensor is able to detect H2O2
concentrations in the range of 50.6 ppm to 229.5 ppm. Furthermore,
the sensor response to H2O2 concentrations is linear in a log-log scale
with the adjacent R-square of 0.93. This sensing behavior allows us
to detect and quantify the concentration of H2O2 in the vapor phase.
Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: This study intends to show the influence of the
hydrolytic degradation on the properties of the e-PTFE/NOMEX®
membranes used in fire-protective clothing. The modification of
water vapour permeability, morphology and chemical structure was
examined by MOCON Permatran, electron microscopy scanning
(SEM), and ATR-FTIR, respectively. A decrease in permeability to
water vapour of the aged samples was observed following closure of
transpiration pores. Analysis of fiber morphology indicates the
appearance of defects at the fibers surface with the presence of micro
cavities. ATR-FTIR analysis reveals the presence of a new absorption
band attributed to carboxylic acid terminal groups generated during
the amide bond hydrolysis.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: Natural dyes are gaining interest due their expected
low risk to human health and to the environment. In this study, the
wash fastness of a natural coloring matter from the liquid waste
produced in the steam treatment of eucalyptus wood in textile fabrics
was investigated. Specifically, eucalyptus wood extract was used to
dye cotton, nylon and wool in an exhaust dyeing process without the
addition of the traditional mordanting agents and then submitted to
wash fastness analysis. The resulting dyed fabrics were evaluated for
color fastness. It was found that wash fastness of dyed fabrics was
very good to cotton and excellent to nylon and wool.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: Expansive soils are often encountered in many parts
of the world, especially in arid and semi-arid fields. Such kind of
soils, generally including active clay minerals in low water content,
enlarge in volume by absorbing the water through the surface and
cause a great harm to the light structures such as channel coating,
roads and airports. The expansive soils were encountered on the path
of Apa-Hotamış conveyance channel belonging to the State
Hydraulic Works in the region of Konya. In the research done in this
area, it is predicted that the soil has a swollen nature and the soil
should be filled with proper granular equipments by digging the
ground to 50-60 cm. In this study, for purpose of helping the other
research to be done in the same area, it is thought that instead of
replacing swollen soil with the granular soil, by stabilizing it with
polypropylene fiber and using it its original place decreases effect of
swelling percent, in this way the cost will be decreased. Therefore,
laboratory tests were conducted to study the effects of polypropylene
fiber on swelling characteristics of expansive soil. Test results
indicated that inclusion of fiber reduced swell percent of expansive
soil. As the fiber content increased, the unconfined compressive
strength was increased. Finally, it can be said that stabilization of
expansive soils with polypropylene fiber is an effective method.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: The possibility of application the dietary fibers in
production of crackers was observed in this work, as well as their
influence on rheological and textural properties on the dough for
crackers and influence on sensory properties of obtained crackers.
Three different dietary fibers, oat, potato and pea fibers, replaced
10% of wheat flour. Long fermentation process and baking test
method were used for crackers production. The changes of dough for
crackers were observed by rheological methods of determination the
viscoelastic dough properties and by textural measurements. Sensory
quality of obtained crackers was described using quantity descriptive
method (QDA) by trained members of descriptive panel. Additional
analysis of crackers surface was performed by videometer. Based on
rheological determination, viscoelastic properties of dough for
crackers were reduced by application of dietary fibers. Manipulation
of dough with 10% of potato fiber was disabled, thus the recipe
modification included increase in water content at 35%. Dough
compliance to constant stress for samples with dietary fibers
decreased, due to more rigid and stiffer dough consistency compared
to control sample. Also, hardness of dough for these samples
increased and dough extensibility decreased. Sensory properties of
final products, crackers, were reduced compared to control sample.
Application of dietary fibers affected mostly hardness, structure and
crispness of the crackers. Observed crackers were low marked for
flavor and taste, due to influence of fibers specific aroma. The sample
with 10% of potato fibers and increased water content was the most
adaptable to applied stresses and to production process. Also this
sample was close to control sample without dietary fibers by
evaluation of sensory properties and by results of videometer method.
Abstract: Different designs of attenuator systems have been
studied in this research; new analysis have been done on existed
designs considering fibers effect on air flow; it was comprehended
that, at fibers presence, there is an air flow which agglomerates fibers
as a negative effect. So some new representations have been designed
and CFD analysis has been done on them. Afterwards, one of these
representations selected as the most optimum and effective design
which is brought in this paper.
Abstract: In recent years, honeycomb fiber reinforced plastic
(FRP) sandwich panels have been increasingly used in various
industries. Low weight, low price and high mechanical strength are
the benefits of these structures. However, their mechanical properties
and behavior have not been fully explored. The objective of this
study is to conduct a combined numerical-statistical investigation of
honeycomb FRP sandwich beams subject to torsion load. In this
paper, the effect of geometric parameters of sandwich panel on
maximum shear strain in both face and core and angle of torsion in a
honeycomb FRP sandwich structures in torsion is investigated. The
effect of Parameters including core thickness, face skin thickness,
cell shape, cell size, and cell thickness on mechanical behavior of the
structure were numerically investigated. Main effects of factors were
considered in this paper and regression equations were derived.
Taguchi method was employed as experimental design and an
optimum parameter combination for the maximum structure stiffness
has been obtained. The results showed that cell size and face skin
thickness have the most significant impacts on torsion angle,
maximum shear strain in face and core.