Abstract: This paper presents a methodology for probabilistic
assessment of bearing capacity and prediction of failure mechanism
of masonry vaults at the ultimate state with consideration of the
natural variability of Young’s modulus of stones. First, the
computation model is explained. The failure mode corresponds to the
four-hinge mechanism. Based on this consideration, the study of a
vault composed of 16 segments is presented. The Young’s modulus of
the segments is considered as random variable defined by a mean
value and a coefficient of variation. A relationship linking the vault
bearing capacity to the voussoirs modulus variation is proposed. The
most probable failure mechanisms, in addition to that observed in the
deterministic case, are identified for each variability level as well as
their probability of occurrence. The results show that the mechanism
observed in the deterministic case has decreasing probability of
occurrence in terms of variability, while the number of other
mechanisms and their probability of occurrence increases with the
coefficient of variation of Young’s modulus. This means that if a
significant change in the Young’s modulus of the segments is proven,
taking it into account in computations becomes mandatory, both for
determining the vault bearing capacity and for predicting its failure
mechanism.
Abstract: The possibility of application the dietary fibers in
production of crackers was observed in this work, as well as their
influence on rheological and textural properties on the dough for
crackers and influence on sensory properties of obtained crackers.
Three different dietary fibers, oat, potato and pea fibers, replaced
10% of wheat flour. Long fermentation process and baking test
method were used for crackers production. The changes of dough for
crackers were observed by rheological methods of determination the
viscoelastic dough properties and by textural measurements. Sensory
quality of obtained crackers was described using quantity descriptive
method (QDA) by trained members of descriptive panel. Additional
analysis of crackers surface was performed by videometer. Based on
rheological determination, viscoelastic properties of dough for
crackers were reduced by application of dietary fibers. Manipulation
of dough with 10% of potato fiber was disabled, thus the recipe
modification included increase in water content at 35%. Dough
compliance to constant stress for samples with dietary fibers
decreased, due to more rigid and stiffer dough consistency compared
to control sample. Also, hardness of dough for these samples
increased and dough extensibility decreased. Sensory properties of
final products, crackers, were reduced compared to control sample.
Application of dietary fibers affected mostly hardness, structure and
crispness of the crackers. Observed crackers were low marked for
flavor and taste, due to influence of fibers specific aroma. The sample
with 10% of potato fibers and increased water content was the most
adaptable to applied stresses and to production process. Also this
sample was close to control sample without dietary fibers by
evaluation of sensory properties and by results of videometer method.
Abstract: In addition to the advantages of light weight, resistant
corrosion and ease of processing, aluminum is also applied to the
long-span spatial structures. However, the elastic modulus of
aluminum is lower than that of the steel. This paper combines the
high performance aluminum honeycomb panel with the aluminum
latticed shell, forming a new panel-and-rod composite shell structure.
Through comparative analysis between the static and dynamic
performance, the conclusion that the structure of composite shell is
noticeably superior to the structure combined before.
Abstract: Effects of nicotine on pre-partum body weight and
preimplantation embryonic development has been reported
previously. Present study was conducted to determine the effects of
annatto (Bixa orellana)-derived delta-tocotrienol (TCT) (with
presence of 10% gamma-TCT isomer) on the nicotine-induced
reduction in body weight and 8-cell embryonic growth in mice.
Twenty-four 6-8 weeks old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) were gavaged with 0.1 ml tocopherol stripped corn oil. G2
was subcutaneously (s.c.) injected with 3 mg/kg/day of nicotine. G3
received concurrent treatment of nicotine (3 mg/kg/day) and 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers) and G4 was given 60 mg/kg/day of δ-TCT mixture alone.
Body weights were recorded daily during the treatment. On Day 8,
females were superovulated with 5 IU Pregnant Mare’s Serum
Gonadotropin (PMSG) for 48 hours followed with 5 IU human
Chorionic Gonadotropin (hCG) before mated with males at the ratio
of 1:1. Females were sacrificed by cervical dislocation for embryo
collection 48 hours post-coitum. Collected embryos were cultured in
vitro. Results showed that throughout Day 1 to Day 7, the body
weight of nicotine treated group (G2) was significantly lower
(p
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: The development of transport systems has negative
impacts on the environment although it has beneficial effects on
society. The car policy caused many problems such as: - the
spectacular growth of fuel consumption hence the very vast increase
in urban pollution, traffic congestion in certain places and at certain
times, the increase in the number of accidents. The exhaust emissions
from cars and weather conditions are the main factors that determine
the level of pollution in urban atmosphere. These conditions lead to
the phenomenon of heat transfer and radiation occurring between the
air and the soil surface of any town. These exchanges give rise, in
urban areas, to the effects of heat islands that correspond to the
appearance of excess air temperature between the city and its
surrounding space. In this object, we perform a numerical simulation
of the plume generated by the cars exhaust gases and show that these
gases form a screening effect above the urban city which cause the
heat island in the presence of wind flow. This study allows us: 1. To
understand the different mechanisms of interactions between these
phenomena.2. To consider appropriate technical solutions to mitigate
the effects of the heat island.
Abstract: The spindle system is one of the most important
components of machine tool. The dynamic properties of the spindle
affect the machining productivity and quality of the work pieces.
Thus, it is important and necessary to determine its dynamic
characteristics of spindles in the design and development in order to
avoid forced resonance. The finite element method (FEM) has been
adopted in order to obtain the dynamic behavior of spindle system.
For this reason, obtaining the Campbell diagrams and determining the
critical speeds are very useful to evaluate the spindle system
dynamics. The unbalance response of the system to the center of
mass unbalance at the cutting tool is also calculated to investigate the
dynamic behavior. In this paper, we used an ANSYS Parametric
Design Language (APDL) program which based on finite element
method has been implemented to make the full dynamic analysis and
evaluation of the results. Results show that the calculated critical
speeds are far from the operating speed range of the spindle, thus, the
spindle would not experience resonance, and the maximum
unbalance response at operating speed is still with acceptable limit.
ANSYS Parametric Design Language (APDL) can be used by spindle
designer as tools in order to increase the product quality, reducing
cost, and time consuming in the design and development stages.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: Liquid-Liquid Equilibrium (LLE) data are measured
for the ternary mixtures of water + 1-butanol + butyl acetate and
quaternary mixtures of water + 1-butanol + butyl acetate + glycerol at
atmospheric pressure at 313.15 K. In addition, isothermal
vapor–liquid–liquid equilibrium (VLLE) data are determined
experimentally at 333.15 K. The region of heterogeneity is found to
increase as the hydrophilic agent (glycerol) is introduced into the
aqueous mixtures. The experimental data are correlated with the
NRTL model. The predicted results from the solution model with the
model parameters determined from the constituent binaries are also
compared with the experimental values.
Abstract: DNA analysis has been widely accepted as providing
valuable evidence concerning the identity of the source of biological
traces. Our work has showed that DNA samples can survive on
cartridges even after firing. The study also raised the possibility of
determining other information such as the age of the donor. Such
information may be invaluable in certain cases where spent cartridges
from automatic weapons are left behind at the scene of a crime. In
spite of the nature of touch evidence and exposure to high chamber
temperatures during shooting, we were still capable to retrieve
enough DNA for profile typing. In order to estimate age of
contributor, DNA methylation levels were analyzed using EpiTect
system for retrieved DNA. However, results were not conclusive, due
to low amount of input DNA.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: To evaluate the vigor of wheat seeds and stress of
premature aging effects on germination percentage, root length and
shoot length of five wheat cultivars that include Vynak, Karkheh,
Chamran, Star and Kavir which underwent a period of zero, two,
three, four days in terms of premature aging with 41°C temperature
and 100% relative humidity. Seed germination percentage, root
length and shoot length in these conditions were measured. This
experiment was conducted as a factorial completely randomized
design with four replications in laboratory conditions. The results
showed that each of aging treatments used in this experiment can be
used to detect differences in vigor of wheat varieties. Wheat cultivars
illustrated significant differences in germination percentage, root
length and shoot length in terms of premature aging. The wheat
cultivars; Astar and Vynak had maximum germination percentage
and Karkheh, respectively Kavir and Chamran had lowest percentage
of seed germination. Reactions of root and shoot length of wheat
cultivars was also different. The results showed that the seeds with a
stronger vigor affected less in premature aging condition and the
difference between the percentage of seed germination under normal
conditions and stress was significant and the seeds with the weaker
vigor were more sensitive to the premature aging stress and the
premature aging had more severe negative impact on seed vigor.
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: The purpose of this study is to determine the
relationship of anxiety level between male and female undergraduates
at a private university in Malaysia. Convenient sampling method used
in this study in which the students were selected based on the
grouping assigned by the faculty. There were 214 undergraduates
who registered the probability courses had participated in this study.
Mathematics Anxiety Rating Scale (MARS) was the instrument used
in study which used to determine students’ anxiety level towards
probability. Reliability and validity of instrument was done before the
major study was conducted. In the major study, students were given
briefing about the study conducted. Participation of this study was
voluntary. Students were given consent form to determine whether
they agree to participate in the study. Duration of two weeks was
given for students to complete the given online questionnaire. The
data collected will be analyzed using Statistical Package for the
Social Sciences (SPSS) to determine the level of anxiety. There were
three anxiety level, i.e., low, average and high. Students’ anxiety
level was determined based on their scores obtained compared with
the mean and standard deviation. If the scores obtained were below
mean and standard deviation, the anxiety level was low. If the scores
were at below and above the mean and between one standard
deviation, the anxiety level was average. If the scores were above the
mean and greater than one standard deviation, the anxiety level was
high. Results showed that both of genders were having average
anxiety level. Among low, average and high anxiety level, frequency
of males were found to be higher as compared to females. Hence, the
mean values obtained for males (M = 3.62) was higher than females
(M = 3.42). In order to be significant of anxiety level among the
gender, the p-value should be less than .05. The p-value obtained in
this study was .117. However, this value was greater than .05. Thus,
there was no significant difference of anxiety level among the gender.
In other words, there was no relationship of anxiety level with the
gender.
Abstract: This article presents a vibration diagnostic method
designed for Permanent Magnets (PM) electrical machines–traction
motors and generators. Those machines are commonly used in traction
drives of electrical vehicles and small wind or water systems. The
described method is very innovative and unique. Specific structural
properties of machines excited by permanent magnets are used in this
method - electromotive force (EMF) generated due to vibrations. There
was analyzed number of publications, which describe vibration
diagnostic methods, and tests of electrical machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. This work presents field-circuit model,
results of static tests, results of calculations and simulations.
Abstract: Biodiesel is one of the alternative fuels that promising
for substituting petro diesel as energy source which is advantage on
sustainability and ecofriendly. Due to the raw material that tend to
decompose during storage, biodiesel also have the same characteristic
that tend to decompose and formed higher acid value which is the
result of oxidation to double bond on a chain of ester. Decomposition of biodiesel due to oxidation reaction could
prevent by introduce a small amount of antioxidant. The origin of raw
materials and the process for producing biodiesel will determine the
effectiveness of antioxidant. The quality degradation on biodiesel
could evaluate by measuring iodine value and acid number of
biodiesel. Biodiesel made from high fatty acid Jatropha curcas oil by using
esterification and transesterification process will stand on the quality
by introduce 90 ppm pyrogallol powder on the biodiesel, which could
increase Induction period time from 2 hours to more than 6 hours in
rancimat test evaluation.
Abstract: Mobile Adhoc Networks (MANETs) are
infrastructure-less, dynamic network of collections of wireless mobile
nodes communicating with each other without any centralized
authority. A MANET is a mobile device of interconnections through
wireless links, forming a dynamic topology. Routing protocols have a
big role in data transmission across a network. Routing protocols,
two major classifications are unipath and multipath. This study
evaluates performance of an on-demand multipath routing protocol
named Adhoc On-demand Multipath Distance Vector routing
(AOMDV). This study proposes Energy Aware AOMDV (EAAOMDV)
an extension of AOMDV which decreases energy
consumed on a route.