Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: The objective of the study is to investigate the
effect of a footballer-s postural on selected physical fitness
components. Twenty-one (21) subjects of the university male
footballers under the Sport Excellence Center programme were
photographed using qualitative analysis. The postural variables
were stratified manually into normal and anomalies group and
their flexibility, strength and SAQ performance were
compared using the Mann-Whitney Test. The AROM
assessment and SAQ test reported no significance difference
(Z=-.398, p=0.711, p>0.05), similar to the lower body strength
was shown with no significance different (Z=-.493, p=0.640,
p>0.05). In contrast, only 1 RM strength test for the upper
body strength test shown with a significance different (Z=-
2.537, p=0.009, p
Abstract: A mammal-s body can be seen as a blood vessel with
complex tunnels. When heart pumps blood periodically, blood runs
through blood vessels and rebounds from walls of blood vessels.
Blood pressure signals can be measured with complex but periodic
patterns. When an artery is clamped during a surgical operation, the
spectrum of blood pressure signals will be different from that of
normal situation. In this investigation, intestinal artery clamping
operations were conducted to a pig for simulating the situation of
intestinal blocking during a surgical operation. Similarity theory is a
convenient and easy tool to prove that patterns of blood pressure
signals of intestinal artery blocking and unblocking are surely
different. And, the algorithm of Hilbert Huang Transform can be
applied to extract the character parameters of blood pressure pattern.
In conclusion, the patterns of blood pressure signals of two different
situations, intestinal artery blocking and unblocking, can be
distinguished by these character parameters defined in this paper.
Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p
Abstract: Normally business changes are made in order to
change a level of activity in some way, whether it is sales, cash flow,
productivity, or product portfolio. When attempts are made to make
such changes, too often the business reverts to the old levels of
activity as soon as management attention is diverted. Risk
management is a field of growing interest to project managers as well
as in general business and organizational management. There are
several approaches used to manage risk in projects and this paper is a
brief outline of some that you might encounter, with an indication of
their strengths and weaknesses.
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: This paper has introduced a slope photogrammetric mapping using unmanned aerial vehicle. There are two units of UAV has been used in this study; namely; fixed wing and multi-rotor. Both UAVs were used to capture images at the study area. A consumer digital camera was mounted vertically at the bottom of UAV and captured the images at an altitude. The objectives of this study are to obtain three dimensional coordinates of slope area and to determine the accuracy of photogrammetric product produced from both UAVs. Several control points and checkpoints were established Real Time Kinematic Global Positioning System (RTK-GPS) in the study area. All acquired images from both UAVs went through all photogrammetric processes such as interior orientation, exterior orientation, aerial triangulation and bundle adjustment using photogrammetric software. Two primary results were produced in this study; namely; digital elevation model and digital orthophoto. Based on results, UAV system can be used to mapping slope area especially for limited budget and time constraints project.
Abstract: In this study, a double-sided linear switched reluctance
motor (LSRM) drive was investigated as an alternative actuator for
vertical linear transportation applications such as a linear elevator
door, hospital and subway doors which move linearly and where
accurate position control and rapid response is requested. A prototype
sliding elevator door that is focused on a home elevator with LSRMs
is designed. The motor has 6/4 poles, 3 phases, 8A, 24V, 250 W and
250 N pull forces. Air gap between rotor and translator poles of the
designed motor and phase coil-s ideal inductance profile are obtained
in compliance with the geometric dimensions. Operation and
switching sections as motor and generator has been determined from
the inductance profile.
Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: High redundancy and strong uncertainty are two main characteristics for underwater robotic manipulators with unlimited workspace and mobility, but they also make the motion planning and control difficult and complex. In order to setup the groundwork for the research on control schemes, the mathematical representation is built by using the Denavit-Hartenberg (D-H) method [9]&[12]; in addition to the geometry of the manipulator which was studied for establishing the direct and inverse kinematics. Then, the dynamic model is developed and used by employing the Lagrange theorem. Furthermore, derivation and computer simulation is accomplished using the MATLAB environment. The result obtained is compared with mechanical system dynamics analysis software, ADAMS. In addition, the creation of intelligent artificial skin using Interlink Force Sensing ResistorTM technology is presented as groundwork for future work
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: Low-density parity-check (LDPC) codes have been shown to deliver capacity approaching performance; however, problematic graphical structures (e.g. trapping sets) in the Tanner graph of some LDPC codes can cause high error floors in bit-error-ratio (BER) performance under conventional sum-product algorithm (SPA). This paper presents a serial concatenation scheme to avoid the trapping sets and to lower the error floors of LDPC code. The outer code in the proposed concatenation is the LDPC, and the inner code is a high rate array code. This approach applies an interactive hybrid process between the BCJR decoding for the array code and the SPA for the LDPC code together with bit-pinning and bit-flipping techniques. Margulis code of size (2640, 1320) has been used for the simulation and it has been shown that the proposed concatenation and decoding scheme can considerably improve the error floor performance with minimal rate loss.
Abstract: The main purpose of this paper is to investigate a discrete time three–species food chain system with ratio dependence. By employing coincidence degree theory and analysis techniques, sufficient conditions for existence of periodic solutions are established.
Abstract: In illumination variant face recognition, existing
methods extracting face albedo as light normalized image may lead to
loss of extensive facial details, with light template discarded. To
improve that, a novel approach for realistic facial texture
reconstruction by combining original image and albedo image is
proposed. First, light subspaces of different identities are established
from the given reference face images; then by projecting the original
and albedo image into each light subspace respectively, texture
reference images with corresponding lighting are reconstructed and
two texture subspaces are formed. According to the projections in
texture subspaces, facial texture with normal light can be synthesized.
Due to the combination of original image, facial details can be
preserved with face albedo. In addition, image partition is applied to
improve the synthesization performance. Experiments on Yale B and
CMUPIE databases demonstrate that this algorithm outperforms the
others both in image representation and in face recognition.
Abstract: This paper presents an interactive modeling system of
uniform polyhedra using the isomorphic graphs. Especially,
Kepler-Poinsot solids are formed by modifications of dodecahedron
and icosahedron.
Abstract: Ten simply supported grossly underreinforced
tapered concrete beams of full size were tested upto complete
collapse under flexural effect .Out of 10 beams, 5 beams were
nonfibrous and the remaining beams contained fibres. The beams
had a variation in the tapered angle as 2°, 4°, 6°, 8° and 10°. The
concrete mix, conventional steel and the type of fibre used were
held constant. Flat corrugated steel fibres were utilized as
secondary reinforcement. The strength and stability parameters
were measured. It is established that the fibrous tapered beams can
be used economically in earthquake prone areas.