Abstract: This paper presents an approach for the design of
fuzzy logic power system stabilizers using genetic algorithms. In the
proposed fuzzy expert system, speed deviation and its derivative
have been selected as fuzzy inputs. In this approach the parameters of
the fuzzy logic controllers have been tuned using genetic algorithm.
Incorporation of GA in the design of fuzzy logic power system
stabilizer will add an intelligent dimension to the stabilizer and
significantly reduces computational time in the design process. It is
shown in this paper that the system dynamic performance can be
improved significantly by incorporating a genetic-based searching
mechanism. To demonstrate the robustness of the genetic based
fuzzy logic power system stabilizer (GFLPSS), simulation studies on
multimachine system subjected to small perturbation and three-phase
fault have been carried out. Simulation results show the superiority
and robustness of GA based power system stabilizer as compare to
conventionally tuned controller to enhance system dynamic
performance over a wide range of operating conditions.
Abstract: Routing in mobile ad hoc networks is a challenging task because nodes are free to move randomly. In DSR like all On- Demand routing algorithms, route discovery mechanism is associated with great delay. More Clearly in DSR routing protocol to send route reply packet, when current route breaks, destination seeks a new route. In this paper we try to change route selection mechanism proactively. We also define a link stability parameter in which a stability value is assigned to each link. Given this feature, destination node can estimate stability of routes and can select the best and more stable route. Therefore we can reduce the delay and jitter of sending data packets.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.
Abstract: Adaptive observers used in sensorless control of induction motors suffer from instability especally in regenerating mode. In this paper, an optimal feed back gain design is proposed, it can reduce the instability region in the torque speed plane .
Abstract: Neural processors have shown good results for
detecting a certain character in a given input matrix. In this paper, a
new idead to speed up the operation of neural processors for character
detection is presented. Such processors are designed based on cross
correlation in the frequency domain between the input matrix and the
weights of neural networks. This approach is developed to reduce the
computation steps required by these faster neural networks for the
searching process. The principle of divide and conquer strategy is
applied through image decomposition. Each image is divided into
small in size sub-images and then each one is tested separately by
using a single faster neural processor. Furthermore, faster character
detection is obtained by using parallel processing techniques to test the
resulting sub-images at the same time using the same number of faster
neural networks. In contrast to using only faster neural processors, the
speed up ratio is increased with the size of the input image when using
faster neural processors and image decomposition. Moreover, the
problem of local subimage normalization in the frequency domain is
solved. The effect of image normalization on the speed up ratio of
character detection is discussed. Simulation results show that local
subimage normalization through weight normalization is faster than
subimage normalization in the spatial domain. The overall speed up
ratio of the detection process is increased as the normalization of
weights is done off line.
Abstract: In this paper the behavior of the decision feedback
equalizers (DFEs) adapted by the decision-directed or the constant
modulus blind algorithms is presented. An analysis of the error
surface of the corresponding criterion cost functions is first
developed. With the intention of avoiding the ill-convergence of the
algorithm, the paper proposes to modify the shape of the cost
function error surface by using a soft decision instead of the hard
one. This was shown to reduce the influence of false decisions and to
smooth the undesirable minima. Modified algorithms using the soft
decision during a pseudo-training phase with an automatic switch to
the properly tracking phase are then derived. Computer simulations
show that these modified algorithms present better ability to avoid
local minima than conventional ones.
Abstract: The acid rain causes change in pH level of soil it is
directly influence on root and leaf growth. Yield of the crop was
reduced if acidity of soil is more. Acid rain seeps into the earth and
poisons plants and trees by dissolving toxic substances in the soil,
such as aluminum, which get absorbed by the roots. In present
investigation, effect of acid rain on crop Vigna radiata was studied.
The effect of acid rain on change in soil fertility was detected in
which pH of control sample was 6.5 and pH of 1% H2SO4 and 1%
HNO3 were 3.5. Nitrogen nitrate in soil was high in 1% HNO3 treated
soil & Control sample. Ammonium nitrogen in soil was low in 1%
HNO3 & H2SO4 treated soil. Ammonium nitrogen was medium in
control and other samples. The effect of acid rain on seed
germination on 3rd day of germination control sample growth was
6.1cm with plumule 0.001% HNO3 & 0.001% H2SO4 was 5.5cm
with plumule and 8cm with plumule. On 10th day fungal growth was
observed in 1% and 0.1% H2SO4 concentrations when all plants were
dead. The effect of acid rain on crop productivity was investigated on
3rd day roots were developed in plants. On 12th day Vigna radiata
showed more growth in 0.1% HNO3 and 0.1% H2SO4 treated plants
as compare to control plants. On 20th day development of
discoloration of plant pigments were observed on acid treated plants
leaves. On 34th day Vigna radiata showed flower in 0.1% HNO3,
0.01% HNO3 and 0.01% H2SO4treated plants and no flowers were
observed on control plants. On 42th day 0.1% HNO3, 0.01% HNO
and 0.01% H2SO4 treated Vigna radiata variety and control plants
were showed seeds on plants. In Vigna radiate variety 0.1%, 0.01%
HNO3, 0.01% H2SO4treated plants were dead on 46th day and fungal
growth was observed. The toxicological study was carried out on
Vigna radiata plants exposed to 1% HNO3 cells were damaged more
than 1% H2SO4. Leaf sections exposed to 0.001% HNO3 & H2SO4
showed less damaged of cells and pigmentation observed in entire
slide when compare with control plant.
Abstract: This paper presents the results related to the
interference reduction technique in multistage multiuser detector for
asynchronous DS-CDMA system. To meet the real-time
requirements for asynchronous multiuser detection, a bit streaming,
cascade architecture is used. An asynchronous multiuser detection
involves block-based computations and matrix inversions. The paper
covers iterative-based suboptimal schemes that have been studied to
decrease the computational complexity, eliminate the need for matrix
inversions, decreases the execution time, reduces the memory
requirements and uses joint estimation and detection process that
gives better performance than the independent parameter estimation
method. The stages of the iteration use cascaded and bits processed
in a streaming fashion. The simulation has been carried out for
asynchronous DS-CDMA system by varying one parameter, i.e.,
number of users. The simulation result exhibits that system gives
optimum bit error rate (BER) at 3rd stage for 15-users.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: In this paper we propose a Particle Swarm heuristic
optimized Multi-Antenna (MA) system. Efficient MA systems
detection is performed using a robust stochastic evolutionary
computation algorithm based on movement and intelligence of
swarms. This iterative particle swarm optimized (PSO) detector
significantly reduces the computational complexity of conventional
Maximum Likelihood (ML) detection technique. The simulation
results achieved with this proposed MA-PSO detection algorithm
show near optimal performance when compared with ML-MA
receiver. The performance of proposed detector is convincingly
better for higher order modulation schemes and large number of
antennas where conventional ML detector becomes non-practical.
Abstract: This paper describes a 2.4 GHz passive switch mixer
and a 5/2.5 GHz voltage-controlled negative Gm oscillator (VCO)
with an inversion-mode MOS varactor. Both circuits are implemented
using a 1P8M 0.13 μm process. The switch mixer has an input
referred 1 dB compression point of -3.89 dBm and a conversion
gain of -0.96 dB when the local oscillator power is +2.5 dBm.
The VCO consumes only 1.75 mW, while drawing 1.45 mA from a
1.2 V supply voltage. In order to reduce the passives size, the VCO
natural oscillation frequency is 5 GHz. A clocked CMOS divideby-
two circuit is used for frequency division and quadrature phase
generation. The VCO has a -109 dBc/Hz phase noise at 1 MHz
frequency offset and a 2.35-2.5 GHz tuning range (after the frequency
division), thus complying with ZigBee requirements.
Abstract: Solution of some practical problems is reduced to the
solution of the integro-differential equations. But for the numerical
solution of such equations basically quadrature methods or its
combination with multistep or one-step methods are used. The
quadrature methods basically is applied to calculation of the integral
participating in right hand side of integro-differential equations. As
this integral is of Volterra type, it is obvious that at replacement with
its integrated sum the upper limit of the sum depends on a current
point in which values of the integral are defined. Thus we receive the
integrated sum with variable boundary, to work with is hardly.
Therefore multistep method with the constant coefficients, which is
free from noted lack and gives the way for finding it-s coefficients is
present.
Abstract: Generalized Center String (GCS) problem are
generalized from Common Approximate Substring problem
and Common substring problems. GCS are known to be
NP-hard allowing the problems lies in the explosion of
potential candidates. Finding longest center string without
concerning the sequence that may not contain any motifs is
not known in advance in any particular biological gene
process. GCS solved by frequent pattern-mining techniques
and known to be fixed parameter tractable based on the
fixed input sequence length and symbol set size. Efficient
method known as Bpriori algorithms can solve GCS with
reasonable time/space complexities. Bpriori 2 and Bpriori
3-2 algorithm are been proposed of any length and any
positions of all their instances in input sequences. In this
paper, we reduced the time/space complexity of Bpriori
algorithm by Constrained Based Frequent Pattern mining
(CBFP) technique which integrates the idea of Constraint
Based Mining and FP-tree mining. CBFP mining technique
solves the GCS problem works for all center string of any
length, but also for the positions of all their mutated copies
of input sequence. CBFP mining technique construct TRIE
like with FP tree to represent the mutated copies of center
string of any length, along with constraints to restraint
growth of the consensus tree. The complexity analysis for
Constrained Based FP mining technique and Bpriori
algorithm is done based on the worst case and average case
approach. Algorithm's correctness compared with the
Bpriori algorithm using artificial data is shown.
Abstract: Signature represents an individual characteristic of a
person which can be used for his / her validation. For such application
proper modeling is essential. Here we propose an offline signature
recognition and verification scheme which is based on extraction of
several features including one hybrid set from the input signature
and compare them with the already trained forms. Feature points
are classified using statistical parameters like mean and variance.
The scanned signature is normalized in slant using a very simple
algorithm with an intention to make the system robust which is
found to be very helpful. The slant correction is further aided by the
use of an Artificial Neural Network (ANN). The suggested scheme
discriminates between originals and forged signatures from simple
and random forgeries. The primary objective is to reduce the two
crucial parameters-False Acceptance Rate (FAR) and False Rejection
Rate (FRR) with lesser training time with an intension to make the
system dynamic using a cluster of ANNs forming a multiple classifier
system.
Abstract: One promising way to achieve low temperature
combustion regime is the use of a large amount of cooled EGR. In
this paper, the effect of injection timing on low temperature
combustion process and emissions were investigated via three
dimensional computational fluid dynamics (CFD) procedures in a DI
diesel engine using high EGR rates. The results show when
increasing EGR from low levels to levels corresponding to reduced
temperature combustion, soot emission after first increasing, is
decreased beyond 40% EGR and get the lowest value at 58% EGR
rate. Soot and NOx emissions are simultaneously decreased at
advanced injection timing before 20.5 ºCA BTDC in conjunction
with 58% cooled EGR rate in compared to baseline case.
Abstract: In this paper, based on steady-state models of Flexible
AC Transmission System (FACTS) devices, the sizing of static
synchronous series compensator (SSSC) controllers in transmission
network is formed as an optimization problem. The objective of this
problem is to reduce the transmission losses in the network. The
optimization problem is solved using particle swarm optimization
(PSO) technique. The Newton-Raphson load flow algorithm is
modified to consider the insertion of the SSSC devices in the
network. A numerical example, illustrating the effectiveness of the
proposed algorithm, is introduced. In addition, a novel model of a 3-
phase voltage source converter (VSC) that is suitable for series
connected FACTS a controller is introduced. The model is verified
by simulation using Power System Blockset (PSB) and Simulink
software.
Abstract: Many studies have emphasized the importance of
resistive exercise to maintain a healthy human body, particular in
prevention of weakening of physical strength. Recently, some studies
advocated that an application of vibration as a supplementary means in
a regular training was effective in encouraging physical strength. Aim
of the current study was, therefore, to identify if an application of
vibration in a resistive exercise was effective in encouraging physical
strength as that in a regular training. A 3-dimensional virtual lower
extremity model for a healthy male and virtual leg-press model were
generated and synchronized. Dynamic leg-press exercises on a slide
machine with/without extra load and on a footboard with vibration as
well as on a slide machine with extra load were analyzed. The results
of the current indicated that the application of the vibration on the
dynamic leg-press exercise might be not greatly effective in
encouraging physical strength, compared with the dynamic leg press
exercise with extra load. It was, however, thought that the application
of the vibration might be helpful to elderly individuals because the
reduced maximum muscle strength appeared by the effect of the
vibration may avoid a muscular spasm, which can be driven from a
high muscle strength sometimes produced during the leg-press
exercise with extra load.
Abstract: Near-infrared (NIR) spectroscopy is a widely used
method for material identification for laboratory and industrial applications.
While standard spectrometers only allow measurements at
one sampling point at a time, NIR Spectral Imaging techniques can
measure, in real-time, both the size and shape of an object as well as
identify the material the object is made of. The online classification
and sorting of recovered paper with NIR Spectral Imaging (SI)
is used with success in the paper recycling industry throughout
Europe. Recently, the globalisation of the recycling material streams
caused that water-based flexographic-printed newspapers mainly from
UK and Italy appear also in central Europe. These flexo-printed
newspapers are not sufficiently de-inkable with the standard de-inking
process originally developed for offset-printed paper. This de-inking
process removes the ink from recovered paper and is the fundamental
processing step to produce high-quality paper from recovered paper.
Thus, the flexo-printed newspapers are a growing problem for the
recycling industry as they reduce the quality of the produced paper
if their amount exceeds a certain limit within the recovered paper
material.
This paper presents the results of a research project for the
development of an automated entry inspection system for recovered
paper that was jointly conducted by CTR AG (Austria) and PTS
Papiertechnische Stiftung (Germany). Within the project an NIR
SI prototype for the identification of flexo-printed newspaper has
been developed. The prototype can identify and sort out flexoprinted
newspapers in real-time and achieves a detection accuracy
for flexo-printed newspaper of over 95%. NIR SI, the technology the
prototype is based on, allows the development of inspection systems
for incoming goods in a paper production facility as well as industrial
sorting systems for recovered paper in the recycling industry in the
near future.
Abstract: In this paper, the sum of squares in linear regression is
reduced to sum of squares in semi-parametric regression. We
indicated that different sums of squares in the linear regression are
similar to various deviance statements in semi-parametric regression.
In addition to, coefficient of the determination derived in linear
regression model is easily generalized to coefficient of the
determination of the semi-parametric regression model. Then, it is
made an application in order to support the theory of the linear
regression and semi-parametric regression. In this way, study is
supported with a simulated data example.
Abstract: A numerical simulation of vortex-induced vibration of
a 2-dimensional elastic circular cylinder with two degree of freedom
under the uniform flow is calculated when Reynolds is 200.
2-dimensional incompressible Navier-Stokes equations are solved
with the space-time finite element method, the equation of the cylinder
motion is solved with the new explicit integral method and the mesh
renew is achieved by the spring moving mesh technology. Considering
vortex-induced vibration with the low reduced damping parameter, the
variety trends of the lift coefficient, the drag coefficient, the
displacement of cylinder are analyzed under different oscillating
frequencies of cylinder. The phenomena of locked-in, beat and
phases-witch were captured successfully. The evolution of vortex
shedding from the cylinder with time is discussed. There are very
similar trends in characteristics between the results of the one degree
of freedom cylinder model and that of the two degree of freedom
cylinder model. The streamwise vibrations have a certain effect on the
lateral vibrations and their characteristics.