Abstract: In this paper a systematic method via H∞ control
design is proposed to select a sensor set that satisfies a number
of input criteria for a MAGLEV suspension system. The proposed
method recovers a number of optimised controllers for each possible
sensor set that satisfies the performance and constraint criteria using
evolutionary algorithms.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.
Abstract: The requirements analysis, modeling, and simulation have consistently been one of the main challenges during the development of complex systems. The scenarios and the state machines are two successful models to describe the behavior of an interactive system. The scenarios represent examples of system execution in the form of sequences of messages exchanged between objects and are a partial view of the system. In contrast, state machines can represent the overall system behavior. The automation of processing scenarios in the state machines provide some answers to various problems such as system behavior validation and scenarios consistency checking. In this paper, we propose a method for translating scenarios in state machines represented by Discreet EVent Specification and procedure to detect implied scenarios. Each induced DEVS model represents the behavior of an object of the system. The global system behavior is described by coupling the atomic DEVS models and validated through simulation. We improve the validation process with integrating formal methods to eliminate logical inconsistencies in the global model. For that end, we use the Z notation.
Abstract: Social learning network analysis has drawn attention
for most researcher on e-learning research domain. This is due to the
fact that it has the capability to identify the behavior of student
during their social interaction inside e-learning. Normally, the social
network analysis (SNA) is treating the students' interaction merely as
node and edge with less meaning. This paper focuses on providing an
ontology structure of e-learning Moodle that can enrich the
relationships among students, as well as between the students and the
teacher. This ontology structure brings great benefit to the future
development of e-learning system.
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: The impact of fixed speed squirrel cage type as well as
variable speed doubly fed induction generators (DFIG) on dynamic
performance of a multimachine power system has been investigated.
Detailed models of the various components have been presented and
the integration of asynchronous and synchronous generators has been
carried out through a rotor angle based transform. Simulation studies
carried out considering the conventional dynamic model of squirrel
cage asynchronous generators show that integration, as such, could
degrade to the AC system performance transiently. This article
proposes a frequency or power controller which can effectively
control the transients and restore normal operation of fixed speed
induction generator quickly. Comparison of simulation results
between classical cage and doubly-fed induction generators indicate
that the doubly fed induction machine is more adaptable to
multimachine AC system. Frequency controller installed in the DFIG
system can also improve its transient profile.
Abstract: One of the most important problems to solve is eye
location for a driver fatigue monitoring system. This paper presents an
efficient method to achieve fast and accurate eye location in grey level
images obtained in the real-word driving conditions. The structure of
eye region is used as a robust cue to find possible eye pairs. Candidates
of eye pair at different scales are selected by finding regions which
roughly match with the binary eye pair template. To obtain real one,
all the eye pair candidates are then verified by using support vector
machines. Finally, eyes are precisely located by using binary vertical
projection and eye classifier in eye pair images. The proposed method
is robust to deal with illumination changes, moderate rotations, glasses
wearing and different eye states. Experimental results demonstrate its
effectiveness.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: In this paper, a method based on Non-Dominated
Sorting Genetic Algorithm (NSGA) has been presented for the Volt /
Var control in power distribution systems with dispersed generation
(DG). Genetic algorithm approach is used due to its broad
applicability, ease of use and high accuracy. The proposed method is
better suited for volt/var control problems. A multi-objective
optimization problem has been formulated for the volt/var control of
the distribution system. The non-dominated sorting genetic algorithm
based method proposed in this paper, alleviates the problem of tuning
the weighting factors required in solving the multi-objective volt/var
control optimization problems. Based on the simulation studies
carried out on the distribution system, the proposed scheme has been
found to be simple, accurate and easy to apply to solve the multiobjective
volt/var control optimization problem of the distribution
system with dispersed generation.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: In this paper, we present a robust and secure
algorithm for watermarking, the watermark is first transformed into
the frequency domain using the discrete wavelet transform (DWT).
Then the entire DWT coefficient except the LL (Band) discarded,
these coefficients are permuted and encrypted by specific mixing.
The encrypted coefficients are inserted into the most significant
spectral components of the stego-image using a chaotic system. This
technique makes our watermark non-vulnerable to the attack (like
compression, and geometric distortion) of an active intruder, or due
to noise in the transmission link.
Abstract: This paper presents a Particle Swarm Optimization
(PSO) method for determining the optimal parameters of a first-order
controller for TCP/AQM system. The model TCP/AQM is described
by a second-order system with time delay. First, the analytical
approach, based on the D-decomposition method and Lemma of
Kharitonov, is used to determine the stabilizing regions of a firstorder
controller. Second, the optimal parameters of the controller are
obtained by the PSO algorithm. Finally, the proposed method is
implemented in the Network Simulator NS-2 and compared with the
PI controller.
Abstract: A structural study of an aqueous electrolyte whose
experimental results are available. It is a solution of LiCl-6H2O type
at glassy state (120K) contrasted with pure water at room temperature
by means of Partial Distribution Functions (PDF) issue from neutron
scattering technique. Based on these partial functions, the Reverse
Monte Carlo method (RMC) computes radial and angular correlation
functions which allow exploring a number of structural features of
the system. The obtained curves include some artifacts. To remedy
this, we propose to introduce a screened potential as an additional
constraint. Obtained results show a good matching between
experimental and computed functions and a significant improvement
in PDFs curves with potential constraint. It suggests an efficient fit of
pair distribution functions curves.
Abstract: Overcurrent (OC) relays are the major protection
devices in a distribution system. The operating time of the OC relays
are to be coordinated properly to avoid the mal-operation of the
backup relays. The OC relay time coordination in ring fed
distribution networks is a highly constrained optimization problem
which can be stated as a linear programming problem (LPP). The
purpose is to find an optimum relay setting to minimize the time of
operation of relays and at the same time, to keep the relays properly
coordinated to avoid the mal-operation of relays.
This paper presents two phase simplex method for optimum time
coordination of OC relays. The method is based on the simplex
algorithm which is used to find optimum solution of LPP. The
method introduces artificial variables to get an initial basic feasible
solution (IBFS). Artificial variables are removed using iterative
process of first phase which minimizes the auxiliary objective
function. The second phase minimizes the original objective function
and gives the optimum time coordination of OC relays.
Abstract: Recently global concerns for the energy security have
steadily been on the increase and are expected to become a major
issue over the next few decades. Energy security refers to a resilient
energy system. This resilient system would be capable of
withstanding threats through a combination of active, direct security
measures and passive or more indirect measures such as redundancy,
duplication of critical equipment, diversity in fuel, other sources of
energy, and reliance on less vulnerable infrastructure. Threats and
disruptions (disturbances) to one part of the energy system affect
another. The paper presents methodology in theoretical background
about energy system as an interconnected network and energy supply
disturbances impact to the network. The proposed methodology uses
a network flow approach to develop mathematical model of the
energy system network as the system of nodes and arcs with energy
flowing from node to node along paths in the network.
Abstract: The purpose of this paper isunavailability of the two main types of conveSwedish traction power supply (TPS) system, i.e.static converter. The number of outages and the ouused to analyze and compare the unavailability oconverters. The mean cumulative function (MCF)analyze the number of outages and the unavailabthe forced outage rate (FOR) concept has been uoutage rates. The study shows that the outagesfailure occur at a constant rate by calendar timconverter stations, while very few stations havedecreasing rate. It has also been found that the stata higher number of outages and a higher outage ratcompared to the rotary converter types. The resultsthat combining the number of outages and the fgives a better view of the converters performasupport for the maintenance decision. In fact, usingdoes not reflect reality. Comparing these two indein identifying the areas where extra resources are maintenance planning and where improvementsoutage in the TPS system.KeywordsFrequency Converter, Forced OuCumulative Function, Traction Power Supply, ESystems.
Abstract: We present a new method for the fully automatic 3D
reconstruction of the coronary artery centerlines, using two X-ray
angiogram projection images from a single rotating monoplane
acquisition system. During the first stage, the input images are
smoothed using curve evolution techniques. Next, a simple yet
efficient multiscale method, based on the information of the Hessian
matrix, for the enhancement of the vascular structure is introduced.
Hysteresis thresholding using different image quantiles, is used to
threshold the arteries. This stage is followed by a thinning procedure
to extract the centerlines. The resulting skeleton image is then pruned
using morphological and pattern recognition techniques to remove
non-vessel like structures. Finally, edge-based stereo correspondence
is solved using a parallel evolutionary optimization method based on
f symbiosis. The detected 2D centerlines combined with disparity
map information allow the reconstruction of the 3D vessel
centerlines. The proposed method has been evaluated on patient data
sets for evaluation purposes.
Abstract: Validation of an automation system is an important issue. The goal is to check if the system under investigation, modeled by a Petri net, never enters the undesired states. Usually, tools dedicated to Petri nets such as DESIGN/CPN are used to make reachability analysis. The biggest problem with this approach is that it is impossible to generate the full occurence graph of the system because it is too large. In this paper, we show how computational methods such as temporal logic model checking and Groebner bases can be used to verify the correctness of the design of an automation system. We report our experimental results with two automation systems: the Automated Guided Vehicle (AGV) system and the traffic light system. Validation of these two systems ranged from 10 to 30 seconds on a PC depending on the optimizing parameters.
Abstract: In this paper, novel techniques in increasing the accuracy
and speed of convergence of a Feed forward Back propagation
Artificial Neural Network (FFBPNN) with polynomial activation
function reported in literature is presented. These technique was
subsequently used to determine the coefficients of Autoregressive
Moving Average (ARMA) and Autoregressive (AR) system. The
results obtained by introducing sequential and batch method of weight
initialization, batch method of weight and coefficient update, adaptive
momentum and learning rate technique gives more accurate result
and significant reduction in convergence time when compared t the
traditional method of back propagation algorithm, thereby making
FFBPNN an appropriate technique for online ARMA coefficient
determination.