Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Children and adolescents developing in the worlds of today are facing a getting array of new and old challenges. School counselling is improving rapidly in contemporary education systems around the world. It can be said that counselling system in Turkey was newly borning. In this study, “Family of the Blood" activity is improved with respect to compherensive guidance school program. The sample included 22 adolescents who were high school students. The activity was carried out in 4 sessions, each of which lasted 45 minutes. In the first session, students- personal-social needs were determined. In the second session, in order to warm up, the students were asked three questions consisting of the constructional aspect. In the third session, the counselor and the teacher shared the results of students- responses obtained in the previous session. In the fourth session, the tables formed by students were presented in the classroom. In order to evaluate the activity, three questions were asked of the teacher and counselor. According to the results, the lesson aims of curriculum and counselling aims of curriculum were attained. In the light of literature, the results were discussed and some suggestions were made. It is taken into consideration that the activitiy was beneficial in many respects, similar studies should be carried out in the near future.
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.
Abstract: The steam cracking reactions are always accompanied with the formation of coke which deposits on the walls of the tubular reactors. The investigation has attempted to control catalytic coking by the applying aluminum, zinc and ceramic coating like aluminum-magnesium by thermal spray and pack cementation method. Rate of coke formation during steam cracking of naphtha has been investigated both for uncoated stainless steel (with different alloys) and metal coating constructed with thermal Spray and pack cementation method with metal powders of Aluminum, Aluminum-Magnesium, zinc, silicon, nickel and chromium. The results of the study show that passivating the surface of SS321 with a coating of Aluminum and Aluminum-Magnesium can significantly reduce the rate of coke deposition during naphtha pyrolysis. SEM and EDAX techniques (Philips XL Series) were used to examine the coke deposits formed by the metal-hydrocarbon reactions. Our objective was to separate the different stages by identifying the characteristic morphologies.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.
Abstract: An international cooperation between educators in
Australia and the US has led to a reconceptualization of the teaching
of a library science course at Appalachian State University. The
pedagogy of Action Learning coupled with a 3D virtual learning
environment immerses students in a social constructivist learning
space that incorporates and supports interaction and reflection. The
intent of this study was to build a bridge between theory and practice
by providing students with a tool set that promoted personal and
social reflection, and created and scaffolded a community of practice.
Besides, action learning is an educational process whereby the fifty
graduate students experienced their own actions and experience to
improve performance.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: In this paper, a new dependable algorithm based on an adaptation of the standard variational iteration method (VIM) is used for analyzing the transition from steady convection to chaos for lowto-intermediate Rayleigh numbers convection in porous media. The solution trajectories show the transition from steady convection to chaos that occurs at a slightly subcritical value of Rayleigh number, the critical value being associated with the loss of linear stability of the steady convection solution. The VIM is treated as an algorithm in a sequence of intervals for finding accurate approximate solutions to the considered model and other dynamical systems. We shall call this technique as the piecewise VIM. Numerical comparisons between the piecewise VIM and the classical fourth-order Runge–Kutta (RK4) numerical solutions reveal that the proposed technique is a promising tool for the nonlinear chaotic and nonchaotic systems.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: The following paper shows an interactive tool which
main purpose is to teach how to play a flute. It consists of three
stages the first one is the instruction and teaching process through a
software application, the second is the practice part when the user
starts to play the flute (hardware specially designed for this
application) this flute is capable of capturing how is being played the
flute and the final stage is the one in which the data captured are sent
to the software and the user is evaluated in order to give him / she a
correction or an acceptance
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: In this paper, we have applied the homotopy perturbation
method (HPM) for obtaining the analytical solution of unsteady
flow of gas through a porous medium and we have also compared the
findings of this research with some other analytical results. Results
showed a very good agreement between results of HPM and the
numerical solutions of the problem rather than other analytical solutions
which have previously been applied. The results of homotopy
perturbation method are of high accuracy and the method is very
effective and succinct.
Abstract: This paper describes a platform that faces the main
research areas for e-learning educational contents. Reusability tackles
the possibility to use contents in different courses reducing costs and
exploiting available data from repositories. In our approach the
production of educational material is based on templates to reuse
learning objects. In terms of interoperability the main challenge lays
on reaching the audience through different platforms. E-learning
solution must track social consumption evolution where nowadays
lots of multimedia contents are accessed through the social networks.
Our work faces it by implementing a platform for generation of
multimedia presentations focused on the new paradigm related to
social media. The system produces videos-courses on top of web
standard SMIL (Synchronized Multimedia Integration Language)
ready to be published and shared. Regarding interfaces it is
mandatory to satisfy user needs and ease communication. To
overcome it the platform deploys virtual teachers that provide natural
interfaces while multimodal features remove barriers to pupils with
disabilities.
Abstract: An implementation of a design for a game based
virtual learning environment is described. The game is developed for a course in analogue electronics, and the topic is the design of a
power supply. This task can be solved in a number of different ways, with certain constraints, giving the students a certain amount of
freedom, although the game is designed not to facilitate trial-and error approach. The use of storytelling and a virtual gaming environment provides the student with the learning material in a
MMORPG environment. The game is tested on a group of second
year electrical engineering students with good results.
Abstract: Cavitation, usually known as a destructive
phenomenon, involves turbulent unsteady two-phase flow. Having
such features, cavitating flows have been turned to a challenging
topic in numerical studies and many researches are being done for
better understanding of bubbly flows and proposing solutions to
reduce its consequent destructive effects. Aeration may be regarded
as an effective protection against cavitation erosion in many
hydraulic structures, like gated tunnels. The paper concerns
numerical simulation of flow in discharge gated tunnel of a dam
using ing RNG k -ε model coupled with the volume of fluid (VOF)
method and the zone which is susceptible of cavitation inception in
the tunnel is predicted. In the second step, a vent is considered in the
mentioned zone for aeration and the numerical simulation is done
again to study the effects of aeration. The results show that aeration
is an impressively useful method to exclude cavitation in mentioned
tunnels.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: This paper is an extension of a previous work where a diagonally implicit harmonic balance method was developed and applied to simulate oscillatory motions of pitching airfoil and wing. A more detailed study on the accuracy, convergence, and the efficiency of the method is carried out in the current paperby varying the number of harmonics in the solution approximation. As the main advantage of the method is itsusage for the design optimization of the unsteady problems, its application to more practical case of rotor flow analysis during forward flight is carried out and compared with flight test data and time-accurate computation results.
Abstract: At present, the tendency to implement the conditionbased
maintenance (CBM), which allows the optimization of the
expenses for equipment monitoring, is more and more evident; also,
the transformer substations with remote monitoring are increasingly
used. This paper reviews all the advantages of the on-line monitoring
and presents an equipment for on-line monitoring of bushings, which
is the own contribution of specialists who are the authors of this
paper. The paper presents a study of the temperature field, using the
finite element method. For carrying out this study, the 3D modelling
of the above mentioned bushing was performed. The analysis study is
done taking into account the extreme thermal stresses, focusing at the
level of the first cooling wing section of the ceramic insulator. This
fact enables to justify the tanδ variation in time, depending on the
transformer loading and the environmental conditions. With a view
to reducing the variation of dielectric losses in bushing insulation, the
use of ferrofuids instead of mineral oils is proposed.