Abstract: This research work is concerned with the life cycle
assessment (LCA) of an expressway, as well as its infrastructure, in
Thailand. The life cycle of an expressway encompasses the raw
material acquisition phase, the construction phase, the use or service
phase, the rehabilitation phase, and finally the demolition and
disposal phase. The LCA in this research was carried out using CML
baseline 2000 and in accordance with the ISO 14040 standard. A
functional unit refers to transportation of one person over one
kilometer of a 3-lane expressway with a 50-year lifetime. This
research has revealed that the construction phase produced the largest
proportion of the environmental impact (81.46%), followed by the
service, rehabilitation, demolition and disposal phases and
transportation at 11.97%, 3.72% 0.33% and 2.52%, respectively. For
the expressway under study, the total carbon footprint over its
lifetime is equivalent to 245,639 tons CO2-eq per 1 kilometer
functional unit, with the phases of construction, service,
rehabilitation, demolition and disposal and transportation
contributing 153,690; 73,773; 3693, 755 and 13,728 tons CO2-eq,
respectively. The findings could be adopted as a benchmark against
which the environmental impacts of future similar projects can be
measured.
Abstract: Frequency stability of microgrids under islanded
operation attracts particular attention recently. A new cooperative
frequency control strategy based on centralized multi-agent system
(CMAS) is proposed in this study. Based on this strategy, agents sent
data and furthermore each component has its own to center operating
decisions (MGCC).After deciding on the information, they are
returned. Frequency control strategies include primary and secondary
frequency control and disposal of multi-stage load in which this study
will also provide a method and algorithm for load shedding. This
could also be a big problem for the performance of micro-grid in
times of disaster. The simulation results show the promising
performance of the proposed structure of the controller based on
multi agent systems.
Abstract: Dissimilar joining of Titanium and Aluminum thin
sheets has potential applications in aerospace and automobile
industry which can reduce weight and cost and improve strength,
corrosion resistance and high temperature properties. However
successful welding of Titanium/Aluminium sheets is of challenge due
to differences in physical, chemical and metallurgical properties
between the two. This paper describes research results of Laser Beam
Welding (LBW) of Ti/Al thin sheets in which many researchers have
recently performed and critically reviewed from different
perspectives. Also some of notable works in the field of laser welding
with changes in mechanical properties, crack propagation, diffusion
behavior, chemical potential, interfacial reaction and the
microstructure are reported.
Abstract: Laser beam welding is an important joining technique
for Titanium/Aluminum thin sheet alloys with their increasing
applications in aerospace, aircraft, automotive, electronics and other
industries. In this paper the research and progress in laser welding of
Ti/Al thin sheets are critically reviewed from different perspectives.
Some important aspects such as microstructure, metallurgical defects
and mechanical properties in weldments are discussed. Also the
recent progress in laser welding of Ti/Al dissimilar thin sheets to
provide a basis for further research work is reported.
Abstract: In this paper, the influence of upstream structures on the flow patternaround and inside the wind-catcher is experimentally investigated by smoke flow visualization techniques. Wind-catchers are an important part of natural ventilation in residential buildings or public places such as shopping centers, libraries, etc. Wind-catchers might be also used in places of high urban densities; hence their potential to provide natural ventilation is dependent on the presence of upstream structures. In this study, the two-sided wind-catcher model was based on a real wind-catcher observed in the city of Yazd, Iran. The present study focuses on the flow patterns around and inside the isolated two-sided wind-catcher, and on a two-sided wind-catcher in the presence of an upstream structure. The results show that the presence of an upstream structure influences the airflow pattern force and direction. Placing a high upstream structure reverses the airflow direction inside the wind-catcher.
Abstract: To elucidate the material characteristics of single
crystals of pure aluminum and copper, the respective relations between
crystallographic orientations and microstructures were examined,
along with bending and mechanical properties. The texture
distribution was also analysed. Bending tests were performed in a
SEM apparatus while its behaviors were observed. Some analytical
results related to crystal direction maps, inverse pole figures, and
textures were obtained from electron backscatter diffraction (EBSD)
analyses.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: This paper discusses the potential benefits of an
interactive multimedia information representation in enhancing
students’ critical thinking aligned with history reasoning in learning
history amongst Secondary School students in Malaysia. Two modes
of multimedia information representation were implemented;
chronologic and thematic information representations. A qualitative
study of an unstructured interview was conducted among two history
teachers, one history education lecturer, two i-think experts, and five
students from Form Four secondary school. The interview was to
elicit their opinions on the implementation of thinking maps and
interactive multimedia information representation in history learning.
The key elements of the interactive multimedia (e.g. multiple media,
user control, interactivity and use of timelines and concept maps)
were then considered to improve the learning process. Findings of the
preliminary investigation reveal that the interactive multimedia
information representations have the potential benefits to be
implemented as an instructional resource in enhancing students’
higher order thinking skills (HOTs). This paper concludes by giving
suggestions for future work.
Abstract: Two micromechanical models for 3D smart composite
with embedded periodic or nearly periodic network of generally
orthotropic reinforcements and actuators are developed and applied to
cubic structures with unidirectional orientation of constituents.
Analytical formulas for the effective piezothermoelastic coefficients
are derived using the Asymptotic Homogenization Method (AHM).
Finite Element Analysis (FEA) is subsequently developed and used
to examine the aforementioned periodic 3D network reinforced smart
structures. The deformation responses from the FE simulations are
used to extract effective coefficients. The results from both
techniques are compared. This work considers piezoelectric materials
that respond linearly to changes in electric field, electric
displacement, mechanical stress and strain and thermal effects. This
combination of electric fields and thermo-mechanical response in
smart composite structures is characterized by piezoelectric and
thermal expansion coefficients. The problem is represented by unitcell
and the models are developed using the AHM and the FEA to
determine the effective piezoelectric and thermal expansion
coefficients. Each unit cell contains a number of orthotropic
inclusions in the form of structural reinforcements and actuators.
Using matrix representation of the coupled response of the unit cell,
the effective piezoelectric and thermal expansion coefficients are
calculated and compared with results of the asymptotic
homogenization method. A very good agreement is shown between
these two approaches.
Abstract: This work presents the result of investigations aimed
at determining the hardness of the welded Chromoly (A 4130) steel
plate of 2” thickness. Multi pass welding for the thick sections was
carried out and analyzed for the Chromoly alloy steel plates. The
study of hardness at the weld metal reveals that there is the presence
of different micro structure products which yields diverse properties.
The welding carried out using GMAW with ER70s-2 electrode.
Single V groove design was selected for the butt joint configuration.
The presence of hydrogen has been suppressed by selecting low
hydrogen electrode. Preheating of the plate prior to welding reduces
the cooling rate which also affects the weld metal microstructure. The
shielding gas composition used in this analysis is 80% Ar-20% CO2.
The experimental analysis gives the detailed study of the hardness of
the material.
Abstract: The biosynthesis of nanoparticles by microorganisms,
on the contrary to chemical synthesis, is an environmentally-friendly
process which has low energy requirements. In this investigation, we
used the microorganism Geobacillus wiegelii, strain GWE1, an
aerobic thermophile belonging to genus Geobacillus, isolated from a
drying oven. This microorganism has the ability to reduce selenite
evidenced by the change of color from colorless to red in the culture.
Elemental analysis and composition of the particles were verified
using transmission electron microscopy and energy-dispersive X-ray
analysis. The nanoparticles have a defined spherical shape and a
selenium elemental state. Previous experiments showed that the
presence of the whole microorganism for the reduction of selenite
was not necessary. The results strongly suggested that an intracellular
NADPH/NADH-dependent reductase mediates selenium
nanoparticles synthesis under aerobic conditions. The enzyme was
purified and identified by mass spectroscopy MALDI-TOF TOF
technique. The enzyme is a 1-pyrroline-5-carboxylate dehydrogenase.
Histograms of nanoparticles sizes were obtained. Size distribution
ranged from 40-160 nm, where 70% of nanoparticles have less than
100 nm in size. Spectroscopic analysis showed that the nanoparticles
are composed of elemental selenium. To analyse the effect of pH in
size and morphology of nanoparticles, the synthesis of them was
carried out at different pHs (4.0, 5.0, 6.0, 7.0, 8.0). For
thermostability studies samples were incubated at different
temperatures (60, 80 and 100 ºC) for 1 h and 3 h. The size of all
nanoparticles was less than 100 nm at pH 4.0; over 50% of
nanoparticles have less than 100 nm at pH 5.0; at pH 6.0 and 8.0 over
90% of nanoparticles have less than 100 nm in size. At neutral pH
(7.0) nanoparticles reach a size around 120 nm and only 20% of them
were less than 100 nm. When looking at temperature effect,
nanoparticles did not show a significant difference in size when they
were incubated between 0 and 3 h at 60 ºC. Meanwhile at 80 °C the
nanoparticles suspension lost its homogeneity. A change in size was
observed from 0 h of incubation at 80ºC, observing a size range
between 40-160 nm, with 20% of them over 100 nm. Meanwhile
after 3 h of incubation at size range changed to 60-180 nm with 50%
of them over 100 nm. At 100 °C the nanoparticles aggregate forming
nanorod structures. In conclusion, these results indicate that is
possible to modulate size and shape of biologically synthesized
nanoparticles by modulating pH and temperature.
Abstract: The purpose of this study was to investigate
perceptions of climate change risk to forest ecosystems and forestbased
communities as well as perceived effectiveness of adaptation
strategies for climate change as well as challenges for adaptation.
Data was gathered using a pre-tested semi-structured questionnaire.
Simple random selection technique was applied. For the majority of
issues, the responses were obtained on multi-point likert scales, and
the scores provided were, in turn, used to estimate the means and
other useful estimates. A composite knowledge index developed
using correct responses to a set of self-rated statements were used to
evaluate the issues. The mean of the knowledge index was 0.64. Also
all respondents recorded values of the knowledge index above 0.25.
Increase forest fire was perceived by respondents as the greatest risk
to forest eco-system. Decrease access to water supplies was perceived
as the greatest risk to livelihoods of forest based communities. The
most effective adaptation strategy relevant to climate change risks to
forest eco-systems and forest based communities livelihoods in
Kathmandu valley in Nepal as perceived by the respondents was
reforestation and afforestation. As well, lack of public awareness was
perceived as the major limitation for climate change adaptation.
However, perceived risks as well as effective adaptation strategies
showed an inconsistent association with knowledge indicators and
social-cultural variables. The results provide useful information to
any party who involve with climate change issues in Nepal, since
such attempts would be more effective once the people’s perceptions
on these aspects are taken into account.
Abstract: Climate change would cause mean sea level to rise +1
m by 2100. To prevent coastal floods resulting from the sea level
rising, different flood control structures have been built, with
acceptable protection levels. Gothenburg with the River Göta älv
located on the southwest coast of Sweden is a vulnerable city to the
accelerated rises in mean sea level. We evaluated using a sea barrage
in the River Göta älv to protect Gothenburg during this century. The
highest sea level was estimated to 2.95 m above the current mean sea
level by 2100. To verify flood protection against such high sea levels,
both barriers have to be closed. To prevent high water level in the
River Göta älv reservoir, the barriers would be open when the sea
level is low. The suggested flood control structures would
successfully protect the city from flooding events during this century.
Abstract: Collapsible soils go through radical rearrangement of
their particles when triggered by water, stress or/and vibration,
causing loss of volume. This loss of volume in soil as seen in
foundation failures has caused millions of dollars’ worth of damages
to public facilities and infrastructure and so has an adverse effect on
the society and people. Despite these consequences and the several
studies that are available, more research is still required in the study
of soil collapsibility. Discerning the pedogenesis (formation) of soils
and investigating the combined effects of the different geological soil
properties is key to elucidating and quantifying soils collapsibility.
This study presents a novel laboratory testing regime that would be
undertaken on soil samples where the effects of soil type, compactive
variables (moisture content, density, void ratio, degree of saturation)
and loading are analyzed. It is anticipated that results obtained would
be useful in mapping the trend of the combined effect thus the basis
for evaluating soil collapsibility or collapse potentials encountered in
construction with volume loss problems attributed to collapse.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: Curcuma longa L. (Zingiberaceae), commonly known
as turmeric, has a long history of traditional uses for culinary
purposes as a spice and a food colorant. The present study aimed to
document the ethnobotanical knowledge about Curcuma longa, and
to assess the variation in the herbalists’ experience in Northeastern
Algeria. Data were collected using semi-structured questionnaires
and direct interviews with 30 herbalists. Ethnobotanical indices,
including the fidelity level (FL%), the relative frequency citation
(RFC), and use value (UV) were determined by quantitative methods.
Diversity in the level of knowledge was analyzed using univariate,
non-parametric, and multivariate statistical methods. Three main
categories of uses were recorded for C. longa: for food, for medicine,
and for cosmetic purposes. As a medicine, turmeric was used for the
treatment of gastrointestinal, dermatological, and hepatic diseases.
Medicinal and food uses were correlated with both forms of
preparation (rhizome and powder). The age group did not influence
the use. Multivariate analyses showed a significant variation in
traditional knowledge, associated with the use value, origin, quality,
and efficacy of the drug. The findings suggested that the geographical
origin of C. longa affected the use in Algeria.
Abstract: This paper deals with the problem of automatic rule
generation for fuzzy systems design. The proposed approach is based
on hybrid artificial bee colony (ABC) optimization and weighted least
squares (LS) method and aims to find the structure and parameters of
fuzzy systems simultaneously. More precisely, two ABC based fuzzy
modeling strategies are presented and compared. The first strategy
uses global optimization to learn fuzzy models, the second one
hybridizes ABC and weighted least squares estimate method. The
performances of the proposed ABC and ABC-LS fuzzy modeling
strategies are evaluated on complex modeling problems and compared
to other advanced modeling methods.
Abstract: GRF, Growth regulating factor, genes encode a novel
class of plant-specific transcription factors. The GRF proteins play a
role in the regulation of cell numbers in young and growing tissues
and may act as transcription activations in growth and development
of plants. Identification of GRF genes and their expression are
important in plants to performance of the growth and development of
various organs. In this study, to better understanding the structural
and functional differences of GRFs family, 45 GRF proteins
sequences in A. thaliana, Z. mays, O. sativa, B. napus, B. rapa, H.
vulgare and S. bicolor, have been collected and analyzed through
bioinformatics data mining. As a result, in secondary structure of
GRFs, the number of alpha helices was more than beta sheets and in
all of them QLQ domains were completely in the biggest alpha helix.
In all GRFs, QLQ and WRC domains were completely protected
except in AtGRF9. These proteins have no trans-membrane domain
and due to have nuclear localization signals act in nuclear and they
are component of unstable proteins in the test tube.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.