Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: Cell volume, together with membrane potential and
intracellular hydrogen ion concentration, is an essential biophysical
parameter for normal cellular activity. Cell volumes can be altered by
osmotically active compounds and extracellular tonicity.
In this study, a simple mathematical model of osmotically induced
cell swelling and shrinking is presented. Emphasis is given to water
diffusion across the membrane. The mathematical description of the
cellular behavior consists in a system of coupled ordinary differential
equations. We compare experimental data of cell volume alterations
driven by differences in osmotic pressure with mathematical
simulations under hypotonic and hypertonic conditions. Implications
for a future model are also discussed.
Abstract: Speech Segmentation is the measure of the change
point detection for partitioning an input speech signal into regions
each of which accords to only one speaker. In this paper, we apply
two features based on multi-scale product (MP) of the clean speech,
namely the spectral centroid of MP, and the zero crossings rate of
MP. We focus on multi-scale product analysis as an important tool
for segmentation extraction. The MP is based on making the product
of the speech wavelet transform coefficients (WTC). We have
estimated our method on the Keele database. The results show the
effectiveness of our method. It indicates that the two features can find
word boundaries, and extracted the segments of the clean speech.
Abstract: PLA emerged as a promising polymer because of its
property as a compostable, biodegradable thermoplastic made from
renewable sources. PLA can be polymerized from monomers
(Lactide or Lactic acid) obtained by fermentation processes from
renewable sources such as corn starch or sugarcane. For PLA
synthesis, ring opening polymerization (ROP) of Lactide monomer is
one of the preferred methods. In the literature, the technique mainly
developed for ROP of PLA is based on metal/bimetallic catalyst (Sn,
Zn and Al) or other organic catalysts in suitable solvent. However,
the PLA synthesized using such catalysts may contain trace elements
of the catalyst which may cause toxicity. This work estimated the
usefulness and drawbacks of using different catalysts as well as effect
of alternative energies and future aspects for PLA production.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: This review emphasizes the effectiveness of men’s
participation in preventing domestic violence, and whether nonviolent
(NV) boys’ and men’s perceptions of intimate partner
violence (IPV) prevention programs affect their involvement. The
main goals of this assessment were to investigate (1) how NV men
engaged in anti-violence prevention programs that empower women,
(2) what were the possible perceptions of NV men involved in
prevention programs (3) how to identify effective approaches and
strategies that encouraged NV men to become involved in prevention
programs. This critical review also included the overview of
prevention programs such as: The Mentors in Violence Prevention
Programs (MVP), The White Ribbon Campaign (WRC), and
Domestic Violence Prevention Enhancement and Leadership through
Alliances (DELTA). The review suggested that (1) the expanding
prevention programs need to reach more macro settings such as work
place, faith-based and other community based organizations, and (2)
territory prevention programs should expand through addressing the
long-term effects of violence.
Abstract: These days, the field of tissue engineering is getting
serious attention due to its usefulness. Bone tissue engineering helps
to address and sort-out the critical sized and non-healing orthopedic
problems by the creation of manmade bone tissue. We will design
and validate an efficient numerical model, which will simulate the
effective diffusivity in bone tissue engineering. Our numerical model
will be based on the finite element analysis of the diffusion-reaction
equations. It will have the ability to optimize the diffusivity, even
at multi-scale, with the variation of time. It will also have a special
feature “parametric sweep”, with which we will be able to predict
the oxygen, glucose and cell density dynamics, more accurately. We
will fix these problems by modifying the governing equations, by
selecting appropriate spatio-temporal finite element schemes and by
transient analysis.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: In this letter, we explore exact solutions for the
Horava-Lifshitz gravity. We use of an extension of this theory with
first order dynamical lapse function. The equations of motion have
been derived in a fully consistent scenario. We assume that there
are some spherically symmetric families of exact solutions of this
extended theory of gravity. We obtain exact solutions and investigate
the singularity structures of these solutions. Specially, an exact
solution with the regular horizon is found.
Abstract: The well been of human beings on construction site is
very important, many man power had been lost through accidents
which kills or make workers physically unfit to carry out construction
activities, these in turn have multiple effects on the whole economy.
Thus it is necessary to put all safety items and regulations in place
before construction activities can commence. This study was carried
out in Ondo state of Nigeria to known and analyse the state of health
and safety of construction workers in the state. The study was done
using first hand observation method, 50 construction project sites
were visited in 10 major towns of Ondo state, questionnaires were
distributed and the results were analysed. The result show that
construction workers are being exposed to a lot of construction site
hazards due to lack of inadequate safety programmes and nonprovision
of appropriate safety materials for workers on site. From the
data gotten for each site visited and the statistical analysis, it can be
concluded that occurrence of accident on construction sites depends
significantly on the available safety facilities on the sites. The result of
the regression statistics show that the level of significant of the
dependence of occurrence of accident on the availability of safety
items on site is 0.0362 which is less than 0.05 maximum significant
level required. Therefore a vital way of sustaining our building
strategy is by given a detail attention to provision of adequate health
and safety items on construction sites which will reduce the
occurrence of accident, loss of man power and death of skilled
workers among others.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: The present paper summarizes the analysis of the
request for consultation of information and data on industrial
emissions made publicly available on the web site of the Ministry of
Environment, Land and Sea on integrated pollution prevention and
control from large industrial installations, the so called “AIA Portal”.
As a matter of fact, a huge amount of information on national
industrial plants is already available on internet, although it is usually
proposed as textual documentation or images.
Thus, it is not possible to access all the relevant information
through interoperability systems and also to retrieval relevant
information for decision making purposes as well as rising of
awareness on environmental issue.
Moreover, since in Italy the number of institutional and private
subjects involved in the management of the public information on
industrial emissions is substantial, the access to the information is
provided on internet web sites according to different criteria; thus, at
present it is not structurally homogeneous and comparable.
To overcome the mentioned difficulties in the case of the
Coordinating Committee for the implementation of the Agreement
for the industrial area in Taranto and Statte, operating before the
IPPC permit granting procedures of the relevant installation located
in the area, a big effort was devoted to elaborate and to validate data
and information on characterization of soil, ground water aquifer and
coastal sea at disposal of different subjects to derive a global
perspective for decision making purposes. Thus, the present paper
also focuses on main outcomes matured during such experience.
Abstract: In this paper we describe one critical research
program within a complex, ongoing multi-year project (2010 to 2014
inclusive) with the overall goal to improve the learning outcomes for
first year undergraduate commerce/business students within an
Information Systems (IS) subject with very large enrolment. The
single research program described in this paper is the analysis of
student attitudes and decision making in relation to the availability of
formative assessment feedback via Web-based real time conferencing
and document exchange software (Adobe Connect). The formative
assessment feedback between teaching staff and students is in respect
of an authentic problem-based, team-completed assignment. The
analysis of student attitudes and decision making is investigated via
both qualitative (firstly) and quantitative (secondly) application of the
Theory of Planned Behavior (TPB) with a two statistically-significant
and separate trial samples of the enrolled students. The initial
qualitative TPB investigation revealed that perceived self-efficacy,
improved time-management, and lecturer-student relationship
building were the major factors in shaping an overall favorable
student attitude to online feedback, whilst some students expressed
valid concerns with perceived control limitations identified within the
online feedback protocols. The subsequent quantitative TPB
investigation then confirmed that attitude towards usage, subjective
norms surrounding usage, and perceived behavioral control of usage
were all significant in shaping student intention to use the online
feedback protocol, with these three variables explaining 63 percent of
the variance in the behavioral intention to use the online feedback
protocol. The identification in this research of perceived behavioral
control as a significant determinant in student usage of a specific
technology component within a virtual learning environment (VLE)
suggests that VLEs could now be viewed not as a single, atomic
entity, but as a spectrum of technology offerings ranging from the
mature and simple (e.g., email, Web downloads) to the cutting-edge
and challenging (e.g., Web conferencing and real-time document
exchange). That is, that all VLEs should not be considered the same.
The results of this research suggest that tertiary students have the
technological sophistication to assess a VLE in this more selective
manner.