Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: Anaerobic Digestion has become a promising
technology for biological transformation of organic fraction of the
municipal solid wastes (MSW). In order to represent the kinetic
behavior of such biological process and thereby to design a reactor
system, development of a mathematical model is essential.
Addressing this issue, a simplistic mathematical model has been
developed for anaerobic digestion of MSW in a continuous flow
reactor unit under homogeneous steady state condition. Upon
simulated hydrolysis, the kinetics of biomass growth and substrate
utilization rate are assumed to follow first order reaction kinetics.
Simulation of this model has been conducted by studying sensitivity
of various process variables. The model was simulated using typical
kinetic data of anaerobic digestion MSW and typical MSW
characteristics of Kolkata. The hydraulic retention time (HRT) and
solid retention time (SRT) time were mainly estimated by varying
different model parameters like efficiency of reactor, influent
substrate concentration and biomass concentration. Consequently,
design table and charts have also been prepared for ready use in the
actual plant operation.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: The necessity of updating the numerical models inputs, because of geometrical and resistive variations in rivers subject to solid transport phenomena, requires detailed control and monitoring activities. The human employment and financial resources of these activities moves the research towards the development of expeditive methodologies, able to evaluate the outflows through the measurement of more easily acquirable sizes. Recent studies highlighted the dependence of the entropic parameter on the kinematical and geometrical flow conditions. They showed a meaningful variability according to the section shape, dimension and slope. Such dependences, even if not yet well defined, could reduce the difficulties during the field activities, and also the data elaboration time. On the basis of such evidences, the relationships between the entropic parameter and the geometrical and resistive sizes, obtained through a large and detailed laboratory experience on steady free surface flows in conditions of macro and intermediate homogeneous roughness, are analyzed and discussed.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.
Abstract: In the present study, a heterogeneous and
homogeneous gas flow dispersion model for simulation and
optimisation of a large-scale catalytic slurry reactor for the direct
synthesis of dimethyl ether (DME) from syngas and CO2, using a
churn-turbulent regime was developed. In the heterogeneous gas flow
model the gas phase was distributed into two bubble phases: small
and large, however in the homogeneous one, the gas phase was
distributed into only one large bubble phase. The results indicated
that the heterogeneous gas flow model was in more agreement with
experimental pilot plant data than the homogeneous one.
Abstract: Measurement of competitiveness between countries or regions is an important topic of many economic analysis and scientific papers. In European Union (EU), there is no mainstream approach of competitiveness evaluation and measuring. There are many opinions and methods of measurement and evaluation of competitiveness between states or regions at national and European level. The methods differ in structure of using the indicators of competitiveness and ways of their processing. The aim of the paper is to analyze main sources of competitive potential of the EU Member States with the help of Factor analysis (FA) and to classify the EU Member States to homogeneous units (clusters) according to the similarity of selected indicators of competitiveness factors by Cluster analysis (CA) in reference years 2000 and 2011. The theoretical part of the paper is devoted to the fundamental bases of competitiveness and the methodology of FA and CA methods. The empirical part of the paper deals with the evaluation of competitiveness factors in the EU Member States and cluster comparison of evaluated countries by cluster analysis.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: This paper studies stability of homogeneous beams
with piezoelectric layers subjected to axial load that is simply
supported at both ends lies on a continuous elastic foundation. The
displacement field of beam is assumed based on first order shear
deformation beam theory. Applying the Hamilton's principle, the
governing equation is established. The influences of applied voltage,
dimensionless geometrical parameter and foundation coefficient on
the stability of beam are presented. To investigate the accuracy of the
present analysis, a compression study is carried out with a known
data.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: In this paper the authors propose and verify an approach to control heat flow in machine tool components. Thermal deformations are a main aspect that affects the accuracy of machining. Due to goals of energy efficiency, thermal basic loads should be reduced. This leads to inhomogeneous and time variant temperature profiles. To counteract these negative consequences, material with high melting enthalpy is used as a method for thermal stabilization. The increased thermal capacity slows down the transient thermal behavior. To account for the delayed thermal equilibrium, a control mechanism for thermal flow is introduced. By varying a gap in a heat flow path the thermal resistance of an assembly can be controlled. This mechanism is evaluated in two experimental setups. First to validate the ability to control the thermal resistance and second to prove the possibility of a self-sufficient option based on the selfsensing abilities of thermal shape memory alloys.
Abstract: Workload and resource management are two essential functions provided at the service level of the grid software infrastructure. To improve the global throughput of these software environments, workloads have to be evenly scheduled among the available resources. To realize this goal several load balancing strategies and algorithms have been proposed. Most strategies were developed in mind, assuming homogeneous set of sites linked with homogeneous and fast networks. However for computational grids we must address main new issues, namely: heterogeneity, scalability and adaptability. In this paper, we propose a layered algorithm which achieve dynamic load balancing in grid computing. Based on a tree model, our algorithm presents the following main features: (i) it is layered; (ii) it supports heterogeneity and scalability; and, (iii) it is totally independent from any physical architecture of a grid.
Abstract: The paper presents an analysis of linkages and
structures of co-operation and their intensity like the potential for the
establishment of clusters in the Central and Eastern (Pannonian)
Croatian. Starting from the theoretical elaboration of the need for
entrepreneurs to organize through the cluster model and the terms of
their self-actualization, related to the importance of traditional values
in terms of benefits, social capital and assess where the company now
is, in order to prove the need to create their own identity in terms of
clustering. The institutional dimensions of social capital where the
public sector has the best role in creating the social structure of
clusters, and social dimensions of social capital in terms of trust,
cooperation and networking will be analyzed to what extent the trust
and coherency are present between companies in the Brod posavina
and Pozega slavonia County, expressed through the readiness of
inclusion in clusters in the NUTS II region - Central and Eastern
(Pannonian) Croatia, as a homogeneous economic entity, with
emphasis on limiting factors that stand in the way of greater
competitiveness.
Abstract: The electromagnetic imaging of inhomogeneous
dielectric cylinders buried in a slab medium by transverse electric
(TE) wave illumination is investigated. Dielectric cylinders of
unknown permittivities are buried in second space and scattered a
group of unrelated waves incident from first space where the scattered
field is recorded. By proper arrangement of the various unrelated
incident fields, the difficulties of ill-posedness and nonlinearity are
circumvented, and the permittivity distribution can be reconstructed
through simple matrix operations. The algorithm is based on the
moment method and the unrelated illumination method. Numerical
results are given to demonstrate the capability of the inverse
algorithm. Good reconstruction is obtained even in the presence of
additive Gaussian random noise in measured data. In addition, the
effect of noise on the reconstruction result is also investigated.