Scholarly

Transcutaneous Inductive Powering Links Based on ASK Modulation Techniques

Year: 2012 Volume: 6 Issue: 8 772 - 776 Pages

Abstract: This paper presented a modified efficient inductive powering link based on ASK modulator and proposed efficient class- E power amplifier. The design presents the external part which is located outside the body to transfer power and data to the implanted devices such as implanted Microsystems to stimulate and monitoring the nerves and muscles. The system operated with low band frequency 10MHZ according to industrial- scientific – medical (ISM) band to avoid the tissue heating. For external part, the modulation index is 11.1% and the modulation rate 7.2% with data rate 1 Mbit/s assuming Tbit = 1us. The system has been designed using 0.35-μm fabricated CMOS technology. The mathematical model is given and the design is simulated using OrCAD P Spice 16.2 software tool and for real-time simulation, the electronic workbench MULISIM 11 has been used.

A Robust Approach to the Load Frequency Control Problem with Speed Regulation Uncertainty

Year: 2012 Volume: 6 Issue: 8 764 - 771 Pages

Authors:
S. Z. Sayed Hassen

Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.

An Efficient Approach for Optimal Placement of TCSC in Double Auction Power Market

Year: 2012 Volume: 6 Issue: 8 758 - 763 Pages

Abstract: This paper proposes an investment cost recovery based efficient and fast sequential optimization approach to optimal allocation of thyristor controlled series compensator (TCSC) in competitive power market. The optimization technique has been used with an objective to maximizing the social welfare and minimizing the device installation cost by suitable location and rating of TCSC in the system. The effectiveness of proposed approach for location of TCSC has been compared with some existing methods of TCSC placement, in terms of its impact on social welfare, TCSC investment recovery and optimal generation as well as load patterns. The results have been obtained on modified IEEE 14-bus system.

Real Time Monitoring of Long Slender Shaft by Distributed-Lumped Modeling Techniques

Year: 2012 Volume: 6 Issue: 8 752 - 757 Pages

Abstract: The aim of this paper is to determine the stress levels at the end of a long slender shaft such as a drilling assembly used in the oil or gas industry using a mathematical model in real-time. The torsional deflection experienced by this type of drilling shaft (about 4 KM length and 20 cm diameter hollow shaft with a thickness of 1 cm) can only be determined using a distributed modeling technique. The main objective of this project is to calculate angular velocity and torque at the end of the shaft by TLM method and also analyzing of the behavior of the system by transient response. The obtained result is compared with lumped modeling technique the importance of these results will be evident only after the mentioned comparison. Two systems have different transient responses and in this project because of the length of the shaft transient response is very important.

Modeling of Sensitivity for SPR Biosensors- New Aspects

Year: 2012 Volume: 6 Issue: 8 747 - 751 Pages

Authors:
Volodymyr Chegel

Abstract: The computer modeling is carried out for parameter of sensitivity of optoelectronic chemical and biosensors, using phenomena of surface plasmon resonance (SPR). The physical model of SPR-sensor-s is described with (or without) of modifications of sensitive gold film surface by a dielectric layer. The variants of increasing of sensitivity for SPR-biosensors, constructed on the principle gold – dielectric – biomolecular layer are considered. Two methods of mathematical treatment of SPR-curve are compared – traditional, with estimation of sensor-s response as shift of the SPRcurve minimum and proposed, for system with dielectric layer, using calculating of the derivative in the point of SPR-curve half-width.

Empowering Communications Challenged users using Development Kits

Year: 2012 Volume: 6 Issue: 8 742 - 746 Pages

Abstract: The rapid pace of technological advancement and its consequential widening digital divide has resulted in the marginalization of the disabled especially the communication challenged. The dearth of suitable technologies for the development of assistive technologies has served to further marginalize the communications challenged user population and widen this chasm even further. Given the varying levels of disability there and its associated requirement for customized solution based. This paper explains the use of a Software Development Kits (SDK) for the bridging of this communications divide through the use of industry poplar communications SDKs towards identification of requirements for communications challenged users as well as identification of appropriate frameworks for future development initiatives.

High Speed and Ultra Low-voltage CMOS NAND and NOR Domino Gates

Year: 2012 Volume: 6 Issue: 8 738 - 741 Pages

Abstract: In this paper we ultra low-voltage and high speed CMOS domino logic. For supply voltages below 500mV the delay for a ultra low-voltage NAND2 gate is aproximately 10% of a complementary CMOS inverter. Furthermore, the delay variations due to mismatch is much less than for conventional CMOS. Differential domino gates for AND/NAND and OR/NOR operation are presented.

International Journal of Electrical, Electronic and Communication Sciences

Archive

Last Issue

Top Journal

SUGGEST A JOURNAL