Abstract: Ascorbic acid (AA), commonly known as vitamin C, is essential for normal functioning of the body and maintenance of metabolic integrity. Among its various roles are as an antioxidant, a cofactor in collagen formation and other reactions, as well as reducing physical stress and maintenance of the immune system. Recent collaborative research between the Australian Defence Science and Technology Organisation (DSTO) in Scottsdale, Tasmania and RMIT University has sought to overcome the problems arising from the inherent instability of ascorbic acid during processing and storage of foods. The recent work has demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. The purpose of this current study has been focused upon the influence of spray drying conditions on the properties of encapsulated ascorbic acid. The process was carried out according to a central composite design. Independent variables were: inlet temperature (80-120° C) and feed flow rate (7-14 mL/minute). Process yield, ascorbic acid loss, moisture content, water activity and particle size distribution were analysed as responses. The results have demonstrated the potential of microencapsulation by spray drying as a means to enhance retention. Vitamin retention, moisture content, water activity and process yield were influenced positively by inlet air temperature and negatively by feed flow rate.
Abstract: This work concerns on experimentally investigation
of surfactant flooding in fractured porous media. In this study a series
of water and surfactant injection processes were performed on
micromodels initially saturated with a heavy crude oil. Eight
fractured glass micromodels were used to illustrate effects of
surfactant types and concentrations on oil recovery efficiency in
presence of fractures with different properties i.e. fracture
orientation, length and number of fractures. Two different
surfactants with different concentrations were tested. The results
showed that surfactant flooding would be more efficient by using
SDS surfactant aqueous solution and also by locating injection well
in a proper position respect to fracture properties. This study
demonstrates different physical and chemical conditions that affect
the efficiency of this method of enhanced oil recovery.
Abstract: Silver-exchanged zeolites and clays are used in
polymer composites to confer broad-spectrum antimicrobial
properties on a range of functional materials. Tobermorite is a layer
lattice mineral whose potential as a carrier for Ag+ ions in
antibacterial composites has not yet been investigated. Accordingly,
in this study, synthetic tobermorite was ion-exchanged with 10 wt%
silver ions and the resulting material was incorporated into a
composite film with chitosan. Chitosan is a biocompatible,
biodegradable derivative of chitin, a polysaccharide obtained from
the shells of crustaceans. The solvent-cast Ag+-exchanged
tobermorite-chitosan films were found to exhibit antimicrobial action
against Staphylococcus aureus, Escherichia coli and Pseudomonas
aeruginosa.
Abstract: The current work focuses on rephrasing the harmful
effects of mercury that is being released from a number of sources.
Most of the sources are from the industrial waste water. Different
techniques of mercury removal have been discussed and a brief
comparison among these has been made. The experimental work has
been conducted for two most widely used methods of mercury
removal and comparison in terms of their efficiency has been made.
Abstract: Among the technologies available to reduce methane
emitted from the pig industry, biofiltration seems to be an effective
and inexpensive solution. In methane (CH4) biofiltration, nitrogen is
an important macronutrient for the microorganisms growth. The
objective of this research project was to study the effect of
ammonium (NH4
+) on the performance, the biomass production and
the nitrogen conversion of a biofilter treating methane. For NH4
+
concentrations ranging from 0.05 to 0.5 gN-NH4
+/L, the CH4 removal
efficiency and the dioxide carbon production rate decreased linearly
from 68 to 11.8 % and from 7.1 to 0.5 g/(m3-h), respectively. The dry
biomass content varied from 4.1 to 5.8 kg/(m3 filter bed). For the
same range of concentrations, the ammonium conversion decreased
while the specific nitrate production rate increased. The specific
nitrate production rate presented negative values indicating
denitrification in the biofilter.
Abstract: In this work, the results of mixing study by a jet mixer in a tank have been investigated in the laboratory scale. The tank dimensions are H/D=1 and the jet entrance have been considered in
the center of upper surface of tank. RNG-k-ε model is used as the
turbulent model for the prediction of the pattern of turbulent flow
inside the tank. For this purpose, a tank with volume of 110 liter is
simulated and it has been divided into 410,000 tetrahedral control
cells for performing the calculations. The grids at the vicinity of the
nozzle and suction pare are finer to get more accurate results. The
experimental results showed that in a vertical jet, the lowest mixing
time takes place at 35 degree. In addition, mixing time decreased by
increasing the Reynolds number. Furthermore, the CFD simulation
predicted the items as well a flow patterns precisely that validates the
experiments.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: Permeability reduction induced by asphaltene
precipitation during gas injection is one of the serious problems in
the oil industry. This problem can lead to formation damage and
decrease the oil production rate. In this work, Malaysian light oil
sample has been used to investigate the effect CO2 injection and
Water Alternating Gas (WAG) injection on permeability reduction.
In this work, dynamic core flooding experiments were conducted to
study the effect of CO2 and WAG injection on the amount of
asphaltene precipitated. Core properties after displacement were
inspected for any permeability reduction to study the effect of
asphaltene precipitation on rock properties.
The results showed that WAG injection gave less asphaltene
precipitation and formation damage compared to CO2 injection. The
study suggested that WAG injection can be one of the important
factors of managing asphaltene precipitation.
Abstract: Liquid-liquid extraction is a process using two immiscible
liquids to extract compounds from one phase without high
temperature requirement. Mostly, the technical implementation of
this process is carried out in mixer-settlers or extraction columns. In
real chemical processes, chemicals may have high viscosity and
contain impurities. These impurities may change the settling behavior
of the process without measurably changing the physical properties
of the phases. In the current study, the settling behavior and the affected
parameters in a high-viscosity system were observed. Batchsettling
experiments were performed to experimentally quantify the
settling behavior and the mixer-settler model of Henschke [1] was
used to evaluate the behavior of the toluene + water system. The
viscosity of the system was increased by adding polyethylene glycol
4000 to the aqueous phase. NaCl and Na2SO4 were used to study the
influence of electrolytes. The results from this study show that increasing
the viscosity of water has a higher influence on the settling
behavior in comparison to the effects of the electrolytes. It can be
seen from the experiments that at high salt concentrations, there was
no effect on the settling behavior.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: A study has been carried out to determine the effect of
coating two commercial glass-ionomer cements in either petroleum
jelly or wax. After coating, specimens were stored in water for 24 or
168 hours, then the coating removed and the surface examined.
Coating in wax was found to increase the surface hardness
significantly compared with the uncoated control, whereas coating
the specimens in petroleum jelly led to only a slight increase in
surface hardness. Coating in wax led to no detectable ion release
after either 24 or 168 hours, though there was some ion release after
the coating had been removed and the specimens exposed to water
for a further 24 hours. This shows that soluble species remained in
these specimens. Overall, this study confirms the idea that immature
glass-ionomers should be protected from early exposure to moisture,
and that the protection offered by petroleum jelly is only modest.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: In this paper, vapour-liquid critical locus for the
binary system acetone + chloroform was determined experimentally
over the whole range of composition. The critical property
measurements were carried out using a dynamic-synthetic apparatus,
employed in the dynamic mode. The critical points are visually
determined by observing the critical opalescence and the
simultaneous disappearance and reappearance of the meniscus in the
middle of a high-pressure view cell which withstands operations up
to 673K and 20MPa. The experimental critical points measured in
this work were compared to those available in literature.
Abstract: A large number of chemical, bio-chemical and pollution-control processes use heterogeneous fixed-bed reactors. The use of finite hollow cylindrical catalyst pellets can enhance conversion levels in such reactors. The absence of the pellet core can significantly lower the diffusional resistance associated with the solid phase. This leads to a better utilization of the catalytic material, which is reflected in the higher values for the effectiveness factor, leading ultimately to an enhanced conversion level in the reactor. It is however important to develop a rigorous heterogeneous model for the reactor incorporating the two-dimensional feature of the solid phase owing to the presence of the finite hollow cylindrical catalyst pellet. Presently, heterogeneous models reported in the literature invariably employ one-dimension solid phase models meant for spherical catalyst pellets. The objective of the paper is to present a rigorous model of the fixed-bed reactors containing finite hollow cylindrical catalyst pellets. The reaction kinetics considered here is the widely used Michaelis–Menten kinetics for the liquid-phase bio-chemical reactions. The reaction parameters used here are for the enzymatic degradation of urea. Results indicate that increasing the height to diameter ratio helps to improve the conversion level. On the other hand, decreasing the thickness is apparently not as effective. This could however be explained in terms of the higher void fraction of the bed that causes a smaller amount of the solid phase to be packed in the fixed-bed bio-chemical reactor.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: In this work, several ASP solutions were flooded into
fractured models initially saturated with heavy oil at a constant flow
rate and different geometrical characteristics of fracture. The ASP
solutions are constituted from 2 polymers i.e. a synthetic polymer,
hydrolyzed polyacrylamide as well as a biopolymer, a surfactant and
2types of alkaline. The results showed that using synthetic
hydrolyzed polyacrylamide polymer increases ultimate oil recovery;
however, type of alkaline does not play a significant rule on oil
recovery. In addition, position of the injection well respect to the
fracture system has remarkable effects on ASP flooding. For instance
increasing angle of fractures with mean flow direction causes more
oil recovery and delays breakthrough time. This work can be
accounted as a comprehensive survey on ASP flooding which
considers most of effective factors in this chemical EOR method.
Abstract: Arvia®, a spin-out company of University of Manchester, UK is commercialising a water treatment technology for the removal of low concentrations of organics from water. This technology is based on the adsorption of organics onto graphite based adsorbents coupled with their electrochemical regeneration in a simple electrochemical cell. In this paper, the potential of the process to adsorb microorganisms and electrochemically disinfect them present in water has been demonstrated. Bench scale experiments have indicated that the process of adsorption using graphite adsorbents with electrochemical regeneration can be used for water disinfection effectively. The most likely mechanisms of disinfection of water through this process include direct electrochemical oxidation and electrochemical chlorination.
Abstract: ZnO+Ga2O3 functionally graded thin films (FGTFs)
were examined for their potential use as Solar cell and organic light
emitting diodes (OLEDs). FGTF transparent conducting oxides (TCO)
were fabricated by combinatorial RF magnetron sputtering. The
composition gradient was controlled up to 10% by changing the
plasma power of the two sputter guns. A Ga2O3+ZnO graded region
was placed on the top layer of ZnO. The FGTFs showed up to 80%
transmittance. Their surface resistances were reduced to < 10% by
increasing the Ga2O3: pure ZnO ratio in the TCO. The FGTFs- work
functions could be controlled within a range of 0.18 eV. The
controlled work function is a very promising technology because it
reduces the contact resistance between the anode and Hall transport
layers of OLED and solar cell devices.