Abstract: In this paper, we propose a new algorithm for joint time-delay and direction-of-arrival (DOA) estimation, here called two-dimensional code acquisition, in an asynchronous directsequence code-division multiple-access (DS-CDMA) array system. This algorithm depends on eigenvector-eigenvalue decomposition of sample correlation matrix, and requires to know desired user-s training sequence. The performance of the algorithm is analyzed both analytically and numerically in uncorrelated and coherent multipath environment. Numerical examples show that the algorithm is robust with unknown number of coherent signals.
Abstract: The designing of charge pump with high gain Op-
Amp is a challenging task for getting faithful response .Design of
high performance phase locked loop require ,a design of high
performance charge pump .We have designed a operational amplifier
for reducing the error caused by high speed glitch in a transistor and
mismatch currents . A separate Op-Amp has designed in 180 nm
CMOS technology by CADENCE VIRTUOSO tool. This paper
describes the design of high performance charge pump for GHz
CMOS PLL targeting orthogonal frequency division multiplexing
(OFDM) application. A high speed low power consumption Op-Amp
with more than 500 MHz bandwidth has designed for increasing the
speed of charge pump in Phase locked loop.
Abstract: 4G Communication Networks provide heterogeneous
wireless technologies to mobile subscribers through IP based
networks and users can avail high speed access while roaming across
multiple wireless channels; possible by an organized way to manage
the Quality of Service (QoS) functionalities in these networks. This
paper proposes the idea of developing a novel QoS optimization
architecture that will judge the user requirements and knowing peak
times of services utilization can save the bandwidth/cost factors. The
proposed architecture can be customized according to the network
usage priorities so as to considerably improve a network-s QoS
performance.
Abstract: Coverage is one of the main research interests in wireless sensor networks (WSN), it is used to determine the quality of service (QoS) of the networks. Therefore this paper aims to review the common strategies use in solving coverage problem in WSN. The strategies studied are used during deployment phase where the coverage is calculated based on the placement of the sensors on the region of interest (ROI). The strategies reviewed are categorized into three groups based on the approaches used, namely; force based, grid based or computational geometry based approach.
Abstract: In this work, we are interested in developing a speech denoising tool by using a discrete wavelet packet transform (DWPT). This speech denoising tool will be employed for applications of recognition, coding and synthesis. For noise reduction, instead of applying the classical thresholding technique, some wavelet packet nodes are set to zero and the others are thresholded. To estimate the non stationary noise level, we employ the spectral entropy. A comparison of our proposed technique to classical denoising methods based on thresholding and spectral subtraction is made in order to evaluate our approach. The experimental implementation uses speech signals corrupted by two sorts of noise, white and Volvo noises. The obtained results from listening tests show that our proposed technique is better than spectral subtraction. The obtained results from SNR computation show the superiority of our technique when compared to the classical thresholding method using the modified hard thresholding function based on u-law algorithm.
Abstract: In this paper, a new approach for target recognition based on the Empirical mode decomposition (EMD) algorithm of Huang etal. [11] and the energy tracking operator of Teager [13]-[14] is introduced. The conjunction of these two methods is called Teager-Huang analysis. This approach is well suited for nonstationary signals analysis. The impulse response (IR) of target is first band pass filtered into subsignals (components) called Intrinsic mode functions (IMFs) with well defined Instantaneous frequency (IF) and Instantaneous amplitude (IA). Each IMF is a zero-mean AM-FM component. In second step, the energy of each IMF is tracked using the Teager energy operator (TEO). IF and IA, useful to describe the time-varying characteristics of the signal, are estimated using the Energy separation algorithm (ESA) algorithm of Maragos et al .[16]-[17]. In third step, a set of features such as skewness and kurtosis are extracted from the IF, IA and IMF energy functions. The Teager-Huang analysis is tested on set of synthetic IRs of Sonar targets with different physical characteristics (density, velocity, shape,? ). PCA is first applied to features to discriminate between manufactured and natural targets. The manufactured patterns are classified into spheres and cylinders. One hundred percent of correct recognition is achieved with twenty three echoes where sixteen IRs, used for training, are free noise and seven IRs, used for testing phase, are corrupted with white Gaussian noise.
Abstract: In this paper, we have developed a method to
compute fractal dimension (FD) of discrete time signals, in the
time domain, by modifying the box-counting method. The size
of the box is dependent on the sampling frequency of the
signal. The number of boxes required to completely cover the
signal are obtained at multiple time resolutions. The time
resolutions are made coarse by decimating the signal. The loglog
plot of total number of boxes required to cover the curve
versus size of the box used appears to be a straight line, whose
slope is taken as an estimate of FD of the signal. The results
are provided to demonstrate the performance of the proposed
method using parametric fractal signals. The estimation
accuracy of the method is compared with that of Katz, Sevcik,
and Higuchi methods. In addition, some properties of the FD
are discussed.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: This paper describes a low-voltage and low-power
channel selection analog front end with continuous-time low pass
filters and highly linear programmable gain amplifier (PGA). The
filters were realized as balanced Gm-C biquadratic filters to achieve a
low current consumption. High linearity and a constant wide
bandwidth are achieved by using a new transconductance (Gm) cell.
The PGA has a voltage gain varying from 0 to 65dB, while
maintaining a constant bandwidth. A filter tuning circuit that requires
an accurate time base but no external components is presented.
With a 1-Vrms differential input and output, the filter achieves
-85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA
were implemented in a 0.18um 1P6M n-well CMOS process. They
consume 3.2mW from a 1.8V power supply and occupy an area of
0.19mm2.
Abstract: This paper introduces an adiabatic register file based
on two-phase CPAL (Complementary Pass-Transistor Adiabatic
Logic circuits) with power-gating scheme, which can operate on a
single-phase power clock. A 32×32 single-phase adiabatic register file
with power-gating scheme has been implemented with TSMC 0.18μm
CMOS technology. All the circuits except for the storage cells employ
two-phase CPAL circuits, and the storage cell is based on the
conventional memory one. The two-phase non-overlap power-clock
generator with power-gating scheme is used to supply the proposed
adiabatic register file. Full-custom layouts are drawn. The energy and
functional simulations have been performed using the net-list
extracted from their layouts. Compared with the traditional static
CMOS register file, HSPICE simulations show that the proposed
adiabatic register file can work very well, and it attains about 73%
energy savings at 100 MHz.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: IETF defines mobility support in IPv6, i.e. MIPv6, to
allow nodes to remain reachable while moving around in the IPv6
internet. When a node moves and visits a foreign network, it is still
reachable through the indirect packet forwarding from its home
network. This triangular routing feature provides node mobility but
increases the communication latency between nodes. This deficiency
can be overcome by using a Binding Update (BU) scheme, which let
nodes keep up-to-date IP addresses and communicate with each other
through direct IP routing. To further protect the security of BU, a
Return Routability (RR) procedure was developed. However, it has
been found that RR procedure is vulnerable to many attacks. In this
paper, we will propose a lightweight RR procedure based on
geometric computing. In consideration of the inherent limitation of
computing resources in mobile node, the proposed scheme is
developed to minimize the cost of computations and to eliminate the
overhead of state maintenance during binding updates. Compared with
other CGA-based BU schemes, our scheme is more efficient and
doesn-t need nonce tables in nodes.
Abstract: We have previously introduced an ultrasonic imaging
approach that combines harmonic-sensitive pulse sequences with a
post-beamforming quadratic kernel derived from a second-order
Volterra filter (SOVF). This approach is designed to produce images
with high sensitivity to nonlinear oscillations from microbubble
ultrasound contrast agents (UCA) while maintaining high levels of
noise rejection. In this paper, a two-step algorithm for computing the
coefficients of the quadratic kernel leading to reduction of tissue
component introduced by motion, maximizing the noise rejection and
increases the specificity while optimizing the sensitivity to the UCA
is presented. In the first step, quadratic kernels from individual
singular modes of the PI data matrix are compared in terms of their
ability of maximize the contrast to tissue ratio (CTR). In the second
step, quadratic kernels resulting in the highest CTR values are
convolved. The imaging results indicate that a signal processing
approach to this clinical challenge is feasible.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: Link reliability and transmitted power are two important design constraints in wireless network design. Error control coding (ECC) is a classic approach used to increase link reliability and to lower the required transmitted power. It provides coding gain, resulting in transmitter energy savings at the cost of added decoder power consumption. But the choice of ECC is very critical in the case of wireless sensor network (WSN). Since the WSNs are energy constraint in nature, both the BER and power consumption has to be taken into count. This paper develops a step by step approach in finding suitable error control codes for WSNs. Several simulations are taken considering different error control codes and the result shows that the RS(31,21) fits both in BER and power consumption criteria.
Abstract: This paper provides an in-depth study of Wireless
Sensor Network (WSN) application to monitor and control the
swiftlet habitat. A set of system design is designed and developed
that includes the hardware design of the nodes, Graphical User
Interface (GUI) software, sensor network, and interconnectivity for
remote data access and management. System architecture is proposed
to address the requirements for habitat monitoring. Such applicationdriven
design provides and identify important areas of further work
in data sampling, communications and networking. For this
monitoring system, a sensor node (MTS400), IRIS and Micaz radio
transceivers, and a USB interfaced gateway base station of Crossbow
(Xbow) Technology WSN are employed. The GUI of this monitoring
system is written using a Laboratory Virtual Instrumentation
Engineering Workbench (LabVIEW) along with Xbow Technology
drivers provided by National Instrument. As a result, this monitoring
system is capable of collecting data and presents it in both tables and
waveform charts for further analysis. This system is also able to send
notification message by email provided Internet connectivity is
available whenever changes on habitat at remote sites (swiftlet farms)
occur. Other functions that have been implemented in this system
are the database system for record and management purposes; remote
access through the internet using LogMeIn software. Finally, this
research draws a conclusion that a WSN for monitoring swiftlet
habitat can be effectively used to monitor and manage swiftlet
farming industry in Sarawak.
Abstract: The paper provides an in-depth tutorial of mathematical
construction of maximal length sequences (m-sequences) via primitive
polynomials and how to map the same when implemented in
shift registers. It is equally important to check whether a polynomial
is primitive or not so as to get proper m-sequences. A fast method to
identify primitive polynomials over binary fields is proposed where
the complexity is considerably less in comparison with the standard
procedures for the same purpose.
Abstract: In this work, the physical based device model of
AlGaN/GaN high electron mobility transistors (HEMTs) has been
established and the corresponding device operation behavior has
been investigated also by using Sentaurus TCAD from Synopsys.
Advanced AlGaN/GaN hetero-structures with GaN cap layer and AlN
spacer have been considered and the GaN cap layer and AlN spacer
are found taking important roles on the gate leakage blocking and
off-state breakdown voltage enhancement.