Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: Many real-world optimization problems involve multiple conflicting objectives and the use of evolutionary algorithms to solve the problems has attracted much attention recently. This paper investigates the application of multi-objective optimization technique for the design of a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the performance of a power system. The design objective is to improve both rotor angle stability and system voltage profile. A Genetic Algorithm (GA) based solution technique is applied to generate a Pareto set of global optimal solutions to the given multi-objective optimisation problem. Further, a fuzzy-based membership value assignment method is employed to choose the best compromise solution from the obtained Pareto solution set. Simulation results are presented to show the effectiveness and robustness of the proposed approach.
Abstract: A measurement system for pH array sensors is
introduced to increase accuracy, and decrease non-ideal effects
successfully. An array readout circuit reads eight potentiometric
signals at the same time, and obtains an average value. The deviation
value or the extreme value is counteracted and the output voltage is a
relatively stable value. The errors of measuring pH buffer solutions are
decreased obviously with this measurement system, and the non-ideal
effects, drift and hysteresis, are lowered to 1.638mV/hr and 1.118mV,
respectively. The efficiency and stability are better than single sensor.
The whole sensing characteristics are improved.
Abstract: In this paper, the construction of a detailed spine
model is presented using the LifeMOD Biomechanics Modeler. The
detailed spine model is obtained by refining spine segments in
cervical, thoracic and lumbar regions into individual vertebra
segments, using bushing elements representing the intervertebral
discs, and building various ligamentous soft tissues between
vertebrae. In the sagittal plane of the spine, constant force will be
applied from the posterior to anterior during simulation to determine
dynamic characteristics of the spine. The force magnitude is
gradually increased in subsequent simulations. Based on these
recorded dynamic properties, graphs of displacement-force
relationships will be established in terms of polynomial functions by
using the least-squares method and imported into a haptic integrated
graphic environment. A thoracolumbar spine model with complex
geometry of vertebrae, which is digitized from a resin spine
prototype, will be utilized in this environment. By using the haptic
technique, surgeons can touch as well as apply forces to the spine
model through haptic devices to observe the locomotion of the spine
which is computed from the displacement-force relationship graphs.
This current study provides a preliminary picture of our ongoing
work towards building and simulating bio-fidelity scoliotic spine
models in a haptic integrated graphic environment whose dynamic
properties are obtained from LifeMOD. These models can be helpful
for surgeons to examine kinematic behaviors of scoliotic spines and
to propose possible surgical plans before spine correction operations.
Abstract: With the development of ubiquitous computing,
current user interaction approaches with keyboard, mouse and pen
are not sufficient. Due to the limitation of these devices the useable
command set is also limited. Direct use of hands as an input device is
an attractive method for providing natural Human Computer
Interaction which has evolved from text-based interfaces through 2D
graphical-based interfaces, multimedia-supported interfaces, to fully
fledged multi-participant Virtual Environment (VE) systems.
Imagine the human-computer interaction of the future: A 3Dapplication
where you can move and rotate objects simply by moving
and rotating your hand - all without touching any input device. In this
paper a review of vision based hand gesture recognition is presented.
The existing approaches are categorized into 3D model based
approaches and appearance based approaches, highlighting their
advantages and shortcomings and identifying the open issues.
Abstract: this paper aims to provide an approach to predict the
performance of the product produced after multi-stages of
manufacturing processes, as well as the assembly. Such approach
aims to control and subsequently identify the relationship between
the process inputs and outputs so that a process engineer can more
accurately predict how the process output shall perform based on the
system inputs. The approach is guided by a six-sigma methodology to
obtain improved performance.
In this paper a case study of the manufacture of a hermetic
reciprocating compressor is presented. The application of artificial
neural networks (ANNs) technique is introduced to improve
performance prediction within this manufacturing environment. The
results demonstrate that the approach predicts accurately and
effectively.
Abstract: The Emergency Department of a medical center in
Taiwan cooperated to conduct the research. A predictive model of
triage system is contracted from the contract procedure, selection of
parameters to sample screening. 2,000 pieces of data needed for the
patients is chosen randomly by the computer. After three
categorizations of data mining (Multi-group Discriminant Analysis,
Multinomial Logistic Regression, Back-propagation Neural
Networks), it is found that Back-propagation Neural Networks can
best distinguish the patients- extent of emergency, and the accuracy
rate can reach to as high as 95.1%. The Back-propagation Neural
Networks that has the highest accuracy rate is simulated into the triage
acuity expert system in this research. Data mining applied to the
predictive model of the triage acuity expert system can be updated
regularly for both the improvement of the system and for education
training, and will not be affected by subjective factors.
Abstract: This paper presents strategies for dynamically creating, managing and removing mesh cells during computations in the context of the Material Point Method (MPM). The dynamic meshing approach has been developed to help address problems involving motion of a finite size body in unbounded domains in which the extent of material travel and deformation is unknown a priori, such as in the case of landslides and debris flows. The key idea is to efficiently instantiate and search only cells that contain material points, thereby avoiding unneeded storage and computation. Mechanisms for doing this efficiently are presented, and example problems are used to demonstrate the effectiveness of dynamic mesh management relative to alternative approaches.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: The purpose of this paper is to present the fuzzy contraction
properties of the Hutchinson-Barnsley operator on the fuzzy
hyperspace with respect to the Hausdorff fuzzy metrics. Also we
discuss about the relationships between the Hausdorff fuzzy metrics
on the fuzzy hyperspaces. Our theorems generalize and extend some
recent results related with Hutchinson-Barnsley operator in the metric
spaces.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: WOLED is widely used as lighting for high efficacy and little power consumption. In this research, power factor testing between WOLED and fluorescent lamp to see which one is more efficient in consuming energy. Since both lamps use semiconductor components, so calculation of the power factor need to consider the effects of harmonics. Harmonic make bigger losses. The study is conducted by comparing the value of the power factor regardless of harmonics (DPF) and also by included the harmonics (TPF). The average value of DPF of fluorescent is 0.953 while WOLED is 0.972. The average value of TPF of fluorescent is 0.717 whereas WOLED is 0.933. So from the review of power factor WOLED is more energy efficient than fluorescent lamp.
Abstract: Pressures for urban redevelopment are intensifying in
all large cities. A new logic for urban development is required –
green urbanism – that provides a spatial framework for directing
population and investment inwards to brownfields and greyfields
precincts, rather than outwards to the greenfields. This represents
both a major opportunity and a major challenge for city planners in
pluralist liberal democracies. However, plans for more compact
forms of urban redevelopment are stalling in the face of community
resistance. A new paradigm and spatial planning platform is required
that will support timely multi-level and multi-actor stakeholder
engagement, resulting in the emergence of consensus plans for
precinct-level urban regeneration capable of more rapid
implementation. Using Melbourne, Australia as a case study, this
paper addresses two of the urban intervention challenges – where and
how – via the application of a 21st century planning tool ENVISION
created for this purpose.
Abstract: The purpose of this paper is to contribute to the body
of knowledge in the area of management accounting, particularly
performance measurement systems within the BSC framework, by
investigating empirically the extent of multiple performance
measures usage and their effects on the financial performance of
Jordanian banks in the branches level. Nevertheless, the result of this
study shows that the non-financial measures usages, particularly,
customer oriented indicators and product/ service oriented indicators,
appears to be important as it enhances firm performance.
Remarkably, the findings reveal that there is positive relationship
between the usages of multiple performance measures via overall
BSC measures and financial performance in the branches level.
Abstract: Flexible macroblock ordering (FMO), adopted in the
H.264 standard, allows to partition all macroblocks (MBs) in a frame
into separate groups of MBs called Slice Groups (SGs). FMO can not
only support error-resilience, but also control the size of video packets
for different network types. However, it is well-known that the number
of bits required for encoding the frame is increased by adopting FMO.
In this paper, we propose a novel algorithm that can reduce the bitrate
overhead caused by utilizing FMO. In the proposed algorithm, all MBs
are grouped in SGs based on the similarity of the transform
coefficients. Experimental results show that our algorithm can reduce
the bitrate as compared with conventional FMO.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: This study addresses the effect of impurities on the
crystallization of Na2CO3 produced within a strategy for capturing
CO2 from flue gases by alkaline absorption. A novel technology -
membrane assisted crystallization - is proposed for Na2CO3
crystallization from mother liquors containing impurities. High purity
of Na2CO3•10H2O crystals was obtained without impacting the
performance of the mass transfer of water vapor through membranes
during crystallization.