Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: Given a large sparse signal, great wishes are to
reconstruct the signal precisely and accurately from lease number of
measurements as possible as it could. Although this seems possible
by theory, the difficulty is in built an algorithm to perform the
accuracy and efficiency of reconstructing. This paper proposes a new
proved method to reconstruct sparse signal depend on using new
method called Least Support Matching Pursuit (LS-OMP) merge it
with the theory of Partial Knowing Support (PSK) given new method
called Partially Knowing of Least Support Orthogonal Matching
Pursuit (PKLS-OMP).
The new methods depend on the greedy algorithm to compute the
support which depends on the number of iterations. So to make it
faster, the PKLS-OMP adds the idea of partial knowing support of its
algorithm. It shows the efficiency, simplicity, and accuracy to get
back the original signal if the sampling matrix satisfies the Restricted
Isometry Property (RIP).
Simulation results also show that it outperforms many algorithms
especially for compressible signals.
Abstract: Climate change has profound consequences for the agriculture of south-eastern Australia and its climate-induced water shortage in the Murray-Darling Basin. Post Keynesian Economics (PKE) macro-dynamics, along with Kaleckian investment and growth theory, are used to develop an ecological-economic system dynamics model of this complex nonlinear river basin system. The Murray- Darling Basin Simulation Model (MDB-SM) uses the principles of PKE to incorporate the fundamental uncertainty of economic behaviors of farmers regarding the investments they make and the climate change they face, particularly as regards water ecosystem services. MDB-SM provides a framework for macroeconomic policies, especially for long-term fiscal policy and for policy directed at the sustainability of agricultural water, as measured by socio-economic well-being considerations, which include sustainable consumption and investment in the river basin. The model can also reproduce other ecological and economic aspects and, for certain parameters and initial values, exhibit endogenous business cycles and ecological sustainability with realistic characteristics. Most importantly, MDBSM provides a platform for the analysis of alternative economic policy scenarios. These results reveal the importance of understanding water ecosystem adaptation under climate change by integrating a PKE macroeconomic analytical framework with the system dynamics modelling approach. Once parameterised and supplied with historical initial values, MDB-SM should prove to be a practical tool to provide alternative long-term policy simulations of agricultural water and socio-economic well-being.
Abstract: Pigeon pea (Cajanus cajan) blanched for 20min was dehulled and milled into flour. The flour was incorporated into dried whole fermented maize (Ogi) at five levels. The resultant products were analyzed for chemical and pasting properties. The fortified Ogi samples were also assessed for sensory attributes: appearance, color, flavor, mouth feel and overall acceptability. The protein content in the whole Ogi fortified samples was in the range of 11.2-16.6% and crude fibre 3.22-3.46%. Fortified whole Ogi with pigeon pea at 30%, 40% and 50% of inclusion with pigeon pea flour has higher protein, crude fibre and ash content. Varying range of pasting quality was recorded for the blends, pasting temperature for fortified Obi was in the range of 45.3-49.50C and peak time 5.05-5.210C. The sensory acceptability of the whole Ogi fortified blends prepared into gruel has higher acceptability for various qualities in comparison with the traditional Ogi gruel.
Abstract: In this paper, we propose improved versions of DVHop
algorithm as QDV-Hop algorithm and UDV-Hop algorithm for
better localization without the need for additional range measurement
hardware. The proposed algorithm focuses on third step of DV-Hop,
first error terms from estimated distances between unknown node and
anchor nodes is separated and then minimized. In the QDV-Hop
algorithm, quadratic programming is used to minimize the error to
obtain better localization. However, quadratic programming requires
a special optimization tool box that increases computational
complexity. On the other hand, UDV-Hop algorithm achieves
localization accuracy similar to that of QDV-Hop by solving
unconstrained optimization problem that results in solving a system
of linear equations without much increase in computational
complexity. Simulation results show that the performance of our
proposed schemes (QDV-Hop and UDV-Hop) is superior to DV-Hop
and DV-Hop based algorithms in all considered scenarios.
Abstract: Geometric design is an important part of planning
process design for physical highway to fill up basic function of roads,
to give good traffic service. It is found that most of the road safety
problems occur at the horizontal curves and complex-compound
curves. In this paper, review on Sagarinn-Myinsain Portion of Nay
Pyi Taw - Mandalay highway has been conducted in aspect of
geometric design induced road safety condition. Horizontal
alignment of geometric features and curve details are reviewed based
on (AASHTO) standard and revised by Autodesk Land Desktop
Software. Moreover, 85th Percentile Operation Speeds (V85) with
driver confidence on horizontal curves is evaluated in order to obtain
the range of highway safety factor (FS). The length of the selected
highway portion is 13.65 miles and 8 lanes. The results of this study
can be used to investigate the possible hazardous locations in
advance and to revise how design radius and super elevation should
be for better road safety performance for the selected portion.
Moreover, the relationship between highway safety and highway
geometry characteristics can also be known.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually to some extent the effects of blurred edges and jagged artifacts in the image. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to enhance edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (''jaggies'') along the tangent directions. In order to preserve image features such as edges, angles and textures, the nonlinear diffusion coefficients are locally adjusted according to the first and second order directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: This study aims to initiate sustainable water management for tourist accommodations in Amphawa, Samut Songkram Province, Thailand. Wastewater generated by tourist accommodation was conducted in 10 homestays and resorts in Amphawa during August – October, 2011. The prominent parameters which are of pH, Dissolved Oxygen (DO), Biochemical Oxygen Demand (BOD), Fat Oil and Grease (FOG), Nitrate (No3-), and Phosphate (PO43-) were conducted monthly. The results revealed that some parameters were over national water quality standard (Class II). Especially, 90% of tourist accommodations have been recorded that FOG was over the standard of wastewater quality from accommodation (group I: total room of accommodation less than 200 rooms). Therefore, grease trap and natural treatment should be utilized in tourist accommodations in order to reduce the discharged of fat, oil, and grease from tourism activities. In addition, number of tourists also relate statistically with BOD and Nitrate at 0.05 level of significance.
Abstract: Determining reasonable fees is the main objective of designing the cost estimation and payment systems for consultant contracts. However, project clients utilize different cost estimation and payment systems because of their varying views on the reasonableness of consultant fees. This study reviews the cost estimation and payment systems of consultant contracts for five countries, including the US (Washington State Department of Transportation), Japan (Ministry of Land, Infrastructure, Transport and Tourism), China (Engineering Design Charging Standard) and UK (Her Majesty's Treasure). Specifically, this work investigates the budgeting process, contractor selection method, contractual price negotiation process, cost review, and cost-control concept of the systems used in these countries. The main finding indicates that that project client-s view on whether the fee is high will affect the way he controls it. In the US, the fee is commonly considered to be high. As a result, stringent auditing system (low flexibility given to the consultant) is then applied. In the UK, the fee is viewed to be low by comparing it to the total life-cycle project cost. Thus, a system that has high flexibility in budgeting and cost reviewing is given to the consultant. In terms of the flexibility allowed for the consultant, the systems applied in Japan and China fall between those of the US and UK. Both the US and UK systems are helpful in determining a reasonable fee. However, in the US system, rigid auditing standards must be established and additional cost-audit manpower is required. In the UK system, sufficient historical cost data should be needed to evaluate the reasonableness of the consultant-s proposed fee
Abstract: Knowledge is the foundation for growth and development. Investment in knowledge improves new method for originate knowledge society and knowledge economy. Investment in knowledge embraces expenditure on education and R&D and software. Measuring of investment in knowledge is characteristically complicated. We examine the influence of investment in knowledge in multifactor productivity growth and numbers of patent. We analyze the annual growth of investment in knowledge and we estimate portion of each country intended for produce total investment in knowledge on the whole OECD. We determine the relative efficiency of average patent numbers with average investment in knowledge and we compare GDP growth rates and growth of knowledge investment. The main purpose in this paper is to study to evaluate different aspect, influence and output of investment in knowledge in OECD countries.
Abstract: The Egyptian Bacillus thuringiensis isolate (M5) produce crystal proteins that is toxic against insects was irradiated with UV light to induce mutants. Upon testing 10 of the resulting mutants for their toxicity against cotton leafworm larvae, the three mutants 62, 64 and 85 proved to be the most toxic ones. Upon testing these mutants along with their parental isolate by SDS-PAGE analysis of spores-crystals proteins as well as vegetative cells proteins, new induced bands appeared in the three mutants by UV radiation and also they showed disappearance of some other bands as compared with the wild type isolate. Multiplex PCR technique, with five sets of specific primers, was used to detect the three types of cryI genes cryIAa, cryIAb and cryIAc. Results showed that these three genes exist, as distinctive bands, in the wild type isolate (M5) as well as in mutants 62 and 85, while the mutant 64 had two distinctive bands of cryIAb and cryIAc genes, and a faint band of cryI Aa gene. Finally, these results revealed that mutant 62 is considered as the promising mutant since it is UV resistant, highly toxic against Spodoptera littoralis and active against a wide range of Lepidopteran insects.
Abstract: The objective of this study was to determine the accuracy to estimation fetal weight by Johnson-s method and compares it with actual birth weight. The sample group was 126 infants delivered in Dan KhunThot hospital from January March 2012. Fetal weight was estimated by measuring fundal height according to Johnson-s method. The information was collected by studying historical delivery records and then analyzed by using the statistics of frequency, percentage, mean, and standard deviation. Finally, the difference was analyzed by a paired t-test.The results showed had an average birth weight was 3093.57 ± 391.03 g (mean ± SD) and 3,455 ± 454.55 g average estimated fetal weight by Johnson-s method higher than average actual birth weight was 384.09 grams. When classifying the infants according to birth weight found that low birth weight ( 4000 g) actual birth weight was more than estimated fetal weight. The difference was found between actual birth weight and estimation fetal weight of the minimum weight in high birth weight ( > 4000 g) , the appropriate birth weight (2500-3999g) and low birth weight (
Abstract: The purpose of this research was to study the
motivation factors to influence the decision to choose Thai Fabric. A
multiple-stage sample was utilized to collect 400 samples from
working women who had diverse occupations all over Thailand. This
research was a quantitative analysis and questionnaire was used a tool
to collect data. Descriptive statistics used in this research included
percentage, average, and standard deviation and inferential statistics
included hypothesis testing of one way ANOVA.
The research findings revealed that demographic factors and social
factors had an influence to the positive idea of wearing Thai fabric (F
= 5.377, P value < 0.05). The respondents who had the age over 41
years old had a better positive idea of wearing Thai fabric than other
groups. Moreover, the findings revealed that age had influenced the
positive idea of wearing Thai fabric (F = 3.918, P value < 0.05). The
respondents who had the age over 41 years old also had stronger
believe that wearing Thai fabric to work and social gatherings are
socially acceptable than other groups.
Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: The objective of this study was to examine the interaction between mode of illness onset and psychiatric comorbidity on the health outcomes of persons with ME/CFS. A total of 114 individuals with ME/CFS participated in this study. Individuals completed a battery of baseline measures including the fatigue severity scale and measures of disability. Findings indicated that those with sudden illness onset had more impaired physical health functioning. In addition, among individuals with sudden onset, those without psychiatric comorbidity had greater fatigue severity and lower overall physical health than those with psychiatric comordibity. In contrast, among individuals with gradual illness onset, those with psychiatric comorbity had higher fatigue severity than those without comorbid psychiatric disorders. The health outcomes of individuals who have ME/CFS with or without psychiatric comorbidity are impacted by the mode of illness onset and this suggest that it is important to examine these factors in future research.
Abstract: The objective of this paper is to establish a possible relationship between sustainable business practice and firm performance. Using a field survey methodology, a sample of sixty manufacturing companies in Nigeria was studied. The firms were categorised into two groups, environmentally 'responsible' and 'irresponsible' firms. An investigation was undertaken into the possible relationship between firm performance and three selected indicators of sustainable business practice: employee health and safety (EHS), waste management (WM), and community development (CD), common within the 30 'responsible' firms. Findings from empirical results reveal that the sustainable practices of the 'responsible' firms are significantly related with firm performance. In addition, sustainable practices are inversely related with fines and penalties. The paper concludes that, within the Nigerian setting at least, sustainability affects corporate performance and sustainability may be a possible tool for corporate conflict resolution as evidenced in the reduction of fines, penalties and compensations. The paper therefore recommends research into the relationship between sustainability and conflict management.
Abstract: Eight Etawah cross bred does were divided into two
groups based on body condition score (BCS). Group I (BSC 2, body
weight 25-30 kg; n = 4), and Group II (BSC 3, body weight, 35-40 kg, n=4). All does received intravaginal controlled internal drug
release devices (CIDR) for 10 days, and a prostaglandin F2α at 48 h before CIDR removal. Estrus detection was carried out using
vasectomized buck. Vaginal epithelium was taken to determine estrus cycle. Blood samples were taken every 3-6 hours, started from
moment of CIDR removal until the end of estrus. The results showed vaginal histological indicated estrus occurred at the hours of 25 to 60
and 30 to 70 post CIDR removal in BCS 2 and 3, respectively. Progesterone peak of BCS 2 and BCS 3 were 0.18±0.31 and
0.48±0.31 ng/mL on the hour 0 post CIDR removal. Estradiol -17ß
peak of each group was 53.25±35.08 and 89.91±92.84 pg/mL at 48
post CIDR removal. LH surge only occurred on BCS 3 groups, the LH concentrations were 9.9± 9.1; 4.5± 4.0; and 18.2± 9.1 ng/mL at
45, 48 and 51 hours post CIDR removal, respectively. It was concluded that the BCS had effects on vaginal histological changes
and LH surge.
Abstract: This research gathered local wisdom towards career building of people in Kamchanoad Community, Baan Muang sub-district, Baan Dung district, Udon Thani province. Data was collected through in-depth interviews with village headmen, community board, teachers, monks, Kamchanoad forest managers and revered elderly aged over 60 years old. All of these 30 interviewees have resided in Kamchanoad Community for more than 40. Descriptive data analysis result revealed that the most prominent local wisdom of Kamchanoad community is their beliefs and religion. Most people in the community have strongly maintained local tradition, the festival of appeasing Chao Pu Sri Suttho on the middle of the 6th month of Thai lunar calendar which falls on the same day with Vesak Day. 100 percent of the people in this community are Buddhist. They believe that Naga, an entity or being, taking the form of a serpent, named “Sri Suttho” lives in Kamchanoad forest. The local people worship the serpent and ask for blessings. Another local wisdom of this community is Sinh fabric weaving.
Abstract: Policy management in organizations became rising issue in the last decade. It’s because of today’s regulatory requirements in the organizations. To manage policies in large organizations is an imperative work. However, major challenges facing organizations in the last decade is managing all the policies in the organization and making them an active documents rather than simple (inactive) documents stored in computer hard drive or on a shelf. Because of this challenge, organizations need policy management program. This policy management program can be either manual or automated. This paper presents suggestions towards managing policies in organizations. As well as possible policy management solution or program to be utilized, manual or automated. The research first examines the models and frameworks used for managing policies from various perspectives in the literature of the research area/domain. At the end of this paper, a policy management framework is proposed for managing enterprise policies effectively and in a simplified manner.
Abstract: There have been numerous implementations of
security system using biometric, especially for identification and
verification cases. An example of pattern used in biometric is the iris
pattern in human eye. The iris pattern is considered unique for each
person. The use of iris pattern poses problems in encoding the human
iris.
In this research, an efficient iris recognition method is proposed.
In the proposed method the iris segmentation is based on the
observation that the pupil has lower intensity than the iris, and the
iris has lower intensity than the sclera. By detecting the boundary
between the pupil and the iris and the boundary between the iris and
the sclera, the iris area can be separated from pupil and sclera. A step
is taken to reduce the effect of eyelashes and specular reflection of
pupil. Then the four levels Coiflet wavelet transform is applied to the
extracted iris image. The modified Hamming distance is employed to
measure the similarity between two irises.
This research yields the identification success rate of 84.25% for
the CASIA version 1.0 database. The method gives an accuracy of
77.78% for the left eyes of MMU 1 database and 86.67% for the
right eyes. The time required for the encoding process, from the
segmentation until the iris code is generated, is 0.7096 seconds.
These results show that the accuracy and speed of the method is
better than many other methods.