Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.
Abstract: This work presents a theoretical investigation of the
simultaneous absorption of CO2 and H2S into aqueous solutions of
MDEA and DEA. In this process the acid components react
with the basic alkanolamine solution via an exothermic,
reversible reaction in a gas/liquid absorber. The use of amine
solvents for gas sweetening has been investigated using
process simulation programs called HYSYS and ASPEN. We
use Electrolyte NRTL and Amine Package and Amines
(experimental) equation of state. The effects of temperature and
circulation rate and amine concentration and packed column and
murphree efficiency on the rate of absorption were studied.
When lean amine flow and concentration increase, CO2 and H2S
absorption increase too. With the improvement of inlet amine
temperature in absorber, CO2 and H2S penetrate to upper stages of
absorber and absorption of acid gases in absorber decreases. The CO2
concentration in the clean gas can be greatly influenced by the
packing height, whereas for the H2S concentration in the clean gas the
packing height plays a minor role. HYSYS software can not
estimate murphree efficiency correctly and it applies the same
contributions in all diagrams for HYSYS software. By
improvement in murphree efficiency, maximum temperature
of absorber decrease and the location of reaction transfer to the
stages of bottoms absorber and the absorption of acid gases
increase.
Abstract: Mycophenolic acid (MPA) is a secondary metabolite
produced by Penicillium brevicompactum, which has antibiotic and
immunosuppressive properties. In this study, the first, mycophenolic
acid was produced in a fermentation process by Penicillium
brevicompactum MUCL 19011 in shake flask using a base medium.
The maximum MPA production, product yield and productivity of
process were 1.379 g/L, 18.6 mg/g glucose and 4.9 mg/L. h,
respectively. Also the glucose consumption, biomass and MPA
production profiles were investigated during batch cultivation.
Obtained results showed that MPA production starts approximately
after 180 hours and reaches to a maximum at 280 h. In the next step,
the effects of some various concentrations of enzymatically
hydrolyzed casein on MPA production were evaluated. Maximum
MPA production, product yield and productivity as 3.63 g/L, 49
mg/g glucose and 12.96 mg/L.h, respectively were obtained with
using 30 g/L enzymatically hydrolyzed casein in culture medium.
These values show an enhanced MPA production, product yield and
process productivity pr as 116.8%, 132.8% and 163.2%, respectively.
Abstract: In this paper, we have presented a new multivariate fuzzy time series forecasting method. This method assumes mfactors with one main factor of interest. History of past three years is used for making new forecasts. This new method is applied in forecasting total number of car accidents in Belgium using four secondary factors. We also make comparison of our proposed method with existing methods of fuzzy time series forecasting. Experimentally, it is shown that our proposed method perform better than existing fuzzy time series forecasting methods. Practically, actuaries are interested in analysis of the patterns of causalities in road accidents. Thus using fuzzy time series, actuaries can define fuzzy premium and fuzzy underwriting of car insurance and life insurance for car insurance. National Institute of Statistics, Belgium provides region of risk classification for each road. Thus using this risk classification, we can predict premium rate and underwriting of insurance policy holders.
Abstract: The migration of a deformable drop in simple shear
flow at finite Reynolds numbers is investigated numerically by
solving the full Navier-Stokes equations using a finite
difference/front tracking method. The objectives of this study are to
examine the effectiveness of the present approach to predict the
migration of a drop in a shear flow and to investigate the behavior of
the drop migration with different drop sizes and non-unity viscosity
ratios. It is shown that the drop deformation depends strongly on the
capillary number, so that; the proper non-dimensional number for the
interfacial tension is the capillary number. The rate of migration
increased with increasing the drop radius. In other words, the
required time for drop migration to the centreline decreases. As the
viscosity ratio increases, the drop rotates more slowly and the
lubrication force becomes stronger. The increased lubrication force
makes it easier for the drop to migrate to the centre of the channel.
The migration velocity of the drop vanishes as the drop reaches the
centreline under viscosity ratio of one and non-unity viscosity ratios.
To validate the present calculations, some typical results are
compared with available experimental and theoretical data.
Abstract: This paper discusses a new heavy tailed distribution based data hiding into discrete cosine transform (DCT) coefficients of image, which provides statistical security as well as robustness against steganalysis attacks. Unlike other data hiding algorithms, the proposed technique does not introduce much effect in the stegoimage-s DCT coefficient probability plots, thus making the presence of hidden data statistically undetectable. In addition the proposed method does not compromise on hiding capacity. When compared to the generic block DCT based data-hiding scheme, our method found more robust against a variety of image manipulating attacks such as filtering, blurring, JPEG compression etc.
Abstract: At present the process of formation of corporate
values in Kazakh universities is under the influence of a whole range
of socio-economic and cultural changes: on the one hand universities
must maintain and transmit traditional cultural values of education,
on the other, to improve quality of service and to involve young
people to science, providing thus own competitiveness. Thus, this
article presents some results of two cycles of sociological research
conducted in 2012 and aimed at identifying possible ways to
popularize science and readiness to participate of youth in given
activities, expectations of young scientists and the prospects of future
development of the Kazakh science.
Abstract: Turbulence of the incoming wind field is of paramount
importance to the dynamic response of civil engineering structures. Hence reliable stochastic models of the turbulence should be available from which time series can be generated for dynamic response and
structural safety analysis. In the paper an empirical cross spectral
density function for the along-wind turbulence component over the wind field area is taken as the starting point. The spectrum is spatially
discretized in terms of a Hermitian cross-spectral density matrix for the turbulence state vector which turns out not to be positive
definite. Since the succeeding state space and ARMA modelling of
the turbulence rely on the positive definiteness of the cross-spectral
density matrix, the problem with the non-positive definiteness of such
matrices is at first addressed and suitable treatments regarding it are proposed. From the adjusted positive definite cross-spectral density
matrix a frequency response matrix is constructed which determines the turbulence vector as a linear filtration of Gaussian white noise.
Finally, an accurate state space modelling method is proposed which allows selection of an appropriate model order, and estimation of a state space model for the vector turbulence process incorporating its phase spectrum in one stage, and its results are compared with a conventional ARMA modelling method.
Abstract: Tufting carpet is a very suitable substrate for growing
microorganism such as pathogenic microbes, due to the direct touch
with human body, long washing periods and laying on the floor; in
fact there are 3 major problems: To risk human health, Prepare bad
odors and Destruction of the products.. In the presented research, for
investigation of presence most common microbes on polyester
tufting, first goods laid in a public place (in the corridor fair) for 30
days and the existence of some microbes were investigate on it with
two methods of enrichment in nutrient environments such as
thioglycolate and noutrunt brath, and shake the dust off the polyester
tufting onto cultivation mediums such as blood agar and noutrunt
agar. After the microorganism colonics are grown, the colonies were
separated and six microbial tests such as cataloes and sitrat were
carried out in five phases on the colonics for identifying the varieties
of bacteria. As a result of tests, 5 type of bacteria, such as
Escherichia coli, staphylococcus saprophytic as were identified. Each
of the mentioned bacteria can be seriously harmful for the heath of
human.
Abstract: Current advancements in nanotechnology are dependent
on the capabilities that can enable nano-scientists to extend their eyes
and hands into the nano-world. For this purpose, a haptics (devices
capable of recreating tactile or force sensations) based system for
AFM (Atomic Force Microscope) is proposed. The system enables
the nano-scientists to touch and feel the sample surfaces, viewed
through AFM, in order to provide them with better understanding of
the physical properties of the surface, such as roughness, stiffness and
shape of molecular architecture. At this stage, the proposed work uses
of ine images produced using AFM and perform image analysis to
create virtual surfaces suitable for haptics force analysis. The research
work is in the process of extension from of ine to online process
where interaction will be done directly on the material surface for
realistic analysis.
Abstract: A statistical optimization of the saccharification
process of EFB was studied. The statistical analysis was done by
applying faced centered central composite design (FCCCD) under
response surface methodology (RSM). In this investigation, EFB
dose, enzyme dose and saccharification period was examined, and the
maximum 53.45% (w/w) yield of reducing sugar was found with 4%
(w/v) of EFB, 10% (v/v) of enzyme after 120 hours of incubation. It
can be calculated that the conversion rate of cellulose content of the
substrate is more than 75% (w/w) which can be considered as a
remarkable achievement. All the variables, linear, quadratic and
interaction coefficient, were found to be highly significant, other than
two coefficients, one quadratic and another interaction coefficient.
The coefficient of determination (R2) is 0.9898 that confirms a
satisfactory data and indicated that approximately 98.98% of the
variability in the dependent variable, saccharification of EFB, could
be explained by this model.
Abstract: Integrins are a large family of multidomain α/β cell
signaling receptors. Some integrins contain an additional inserted I
domain, whose earliest expression appears to be with the chordates,
since they are observed in the urochordates Ciona intestinalis (vase
tunicate) and Halocynthia roretzi (sea pineapple), but not in integrins
of earlier diverging species. The domain-s presence is viewed as a
hallmark of integrins of higher metazoans, however in vertebrates,
there are clearly three structurally-different classes: integrins without
I domains, and two groups of integrins with I domains but separable
by the presence or absence of an additional αC helix. For example,
the αI domains in collagen-binding integrins from Osteichthyes
(bony fish) and all higher vertebrates contain the specific αC helix,
whereas the αI domains in non-collagen binding integrins from
vertebrates and the αI domains from earlier diverging urochordate
integrins, i.e. tunicates, do not. Unfortunately, within the early
chordates, there is an evolutionary gap due to extinctions between the
tunicates and cartilaginous fish. This, coupled with a knowledge gap
due to the lack of complete genomic data from surviving species,
means that the origin of collagen-binding αC-containing αI domains
remains unknown. Here, we analyzed two available genomes from
Callorhinchus milii (ghost shark/elephant shark; Chondrichthyes –
cartilaginous fish) and Petromyzon marinus (sea lamprey;
Agnathostomata), and several available Expression Sequence Tags
from two Chondrichthyes species: Raja erinacea (little skate) and
Squalus acanthias (dogfish shark); and Eptatretus burgeri (inshore
hagfish; Agnathostomata), which evolutionary reside between the
urochordates and osteichthyes. In P. marinus, we observed several
fragments coding for the αC-containing αI domain, allowing us to
shed more light on the evolution of the collagen-binding integrins.
Abstract: The technique of k-anonymization has been proposed to obfuscate private data through associating it with at least k identities. This paper investigates the basic tabular structures that
underline the notion of k-anonymization using cell suppression.
These structures are studied under idealized conditions to identify the
essential features of the k-anonymization notion. We optimize data kanonymization
through requiring a minimum number of anonymized
values that are balanced over all columns and rows. We study the
relationship between the sizes of the anonymized tables, the value k, and the number of attributes. This study has a theoretical value through contributing to develop a mathematical foundation of the kanonymization
concept. Its practical significance is still to be
investigated.
Abstract: Fishing has always been an essential component of
the Polynesians- life. Fishhooks, mostly in pearl shell, found during
archaeological excavations are the artifacts related to this activity the
most numerous. Thanks to them, we try to reconstruct the ancient
techniques of resources exploitation, inside the lagoons and offshore.
They can also be used as chronological and cultural indicators. The
shapes and dimensions of these artifacts allow comparisons and
classifications used in both functional approach and chrono-cultural
perspective. Hence it is very important for the ethno-archaeologists
to dispose of reliable methods and standardized measurement of
these artifacts. Such a reliable objective and standardized method
have been previously proposed. But this method cannot be envisaged
manually because of the very important time required to measure
each fishhook manually and the quantity of fishhooks to measure
(many hundreds). We propose in this paper a detailed acquisition
protocol of fishhooks and an automation of every step of this method.
We also provide some experimental results obtained on the fishhooks
coming from three archaeological excavations sites.
Abstract: This paper investigates the effects of lubrication on
the quantity of heat emission of two spur gear. System with and
without lubrication effected on the quantity of heat induced on the
gear box (oil - bearings – gears). Both of lubrication and speed of
motor are affected on the performance of gears. Research investigated
the lubrication on the system with and without loading as well as the
wear of gears and bearing's conditions. Gear box investigated
includes the motor, pump, two spur gears, two shafts; speed change
used pulleys and belts. Load used equal one weight ones of gear.
Lubrication mechanism used jet system (upper and lower jet). Gear
box we used system of jet lubrication is perpendicular direction of
the contact line between two teeth. Results appeared in this work that
the lubrication is the vital parameter which is affected on the
performance and durability of gears and bearings. In macroscopic
observation, we noted that damage of bearings happened during the
absence of lubrication as well as abrasive of wear of teeth. Higher
speed of motor without lubrication increased the noise, but in the
presence of lubrication was decreased.
Abstract: This paper describes a rapid prototyping (RP)
technology for forming a hydroxyapatite (HA) bone scaffold model.
The HA powder and a silica sol are mixed into bioceramic slurry form
under a suitable viscosity. The HA particles are embedded in the
solidified silica matrix to form green parts via a wide range of process
parameters after processing by selective laser sintering (SLS). The
results indicate that the proposed process was possible to fabricate
multilayers and hollow shell structure with brittle property but
sufficient integrity for handling prior to post-processing. The
fabricated bone scaffold models had a surface finish of 25
Abstract: This paper proposed classification models that would
be used as a proxy for hard disk drive (HDD) functional test equitant
which required approximately more than two weeks to perform the
HDD status classification in either “Pass" or “Fail". These models
were constructed by using committee network which consisted of a
number of single neural networks. This paper also included the
method to solve the problem of sparseness data in failed part, which
was called “enforce learning method". Our results reveal that the
constructed classification models with the proposed method could
perform well in the sparse data conditions and thus the models,
which used a few seconds for HDD classification, could be used to
substitute the HDD functional tests.
Abstract: The purpose of this article is to propose a model designed to achieve Total Knowledge Transfer in the public health sector. The Total Knowledge Transfer Model integrated four essential organizational factors which have been under examined in totality in the literature. The research design was inductive in nature and used a case study for accomplishing the research objectives. The researcher investigated the factors that created a base to design a framework for total knowledge transfer in the public health sector. The results of this study are drawn from a fairly large sample in only two hospitals. A further research can be conducted to cover more responses from a wider health sector. The Total Knowledge Transfer Model is essential to improve the transfer and application of total common health knowledge.
Abstract: Higher education has an important role to play in
advocating environmentalism. Given this responsibility, the goal of
higher education should therefore be to develop graduates with the
knowledge, skills and values related to environmentalism. However,
research indicates that there is a lack of consciousness amongst
graduates on the need to be more environmentally aware, especially
when it comes to applying the appropriate knowledge and skills
related to environmentalism. Although institutions of higher learning
do include environmental parameters within their undergraduate and
postgraduate academic programme structures, the environmental
boundaries are usually confined to specific engineering majors within
an engineering programme. This makes environmental knowledge,
skills and values exclusive to certain quarters of the higher education
system. The incorporation of environmental literacy within higher
education institutions as a whole is of utmost pertinence if a nation-s
human capital is to be nurtured to become change agents for the
preservation of environment. This paper discusses approaches that
can be adapted by institutions of higher learning to include
environmental literacy within the graduate-s higher learning
experience.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.