Abstract: A new and highly efficient architecture for elliptic curve scalar point multiplication which is optimized for a binary field recommended by NIST and is well-suited for elliptic curve cryptographic (ECC) applications is presented. To achieve the maximum architectural and timing improvements we have reorganized and reordered the critical path of the Lopez-Dahab scalar point multiplication architecture such that logic structures are implemented in parallel and operations in the critical path are diverted to noncritical paths. With G=41, the proposed design is capable of performing a field multiplication over the extension field with degree 163 in 11.92 s with the maximum achievable frequency of 251 MHz on Xilinx Virtex-4 (XC4VLX200) while 22% of the chip area is occupied, where G is the digit size of the underlying digit-serial finite field multiplier.
Abstract: In order to derive important parameters concerning
mobile subscriber MS with ongoing calls in Low Earth Orbit Mobile
Satellite Systems LEO MSSs, a positioning system had to be
integrated into MSS in order to localize mobile subscribers MSs and
track them during the connection. Such integration is regarded as a
complex implementation. We propose in this paper a novel method
based on advantages of mobility model of Low Earth Orbit Mobile
Satellite System LEO MSS which allows the evaluation of instant of
subsequent handover of a MS even if its location is unknown. This
method is utilized to propose a Dynamic Channel Reservation DCRlike
scheme based on the DCR scheme previously proposed in
literature. Results presented show that DCR-like technique gives
different QoS performance than DCR. Indeed, an improve in
handover blocking probability and an increase in new call blocking
probability are observed for the DCR-like technique.
Abstract: The purpose of this study is to examine the selfefficacy
and life satisfaction levels of students receiving education in
schools of physical education and sports. The population of the study
consisted 263 students, among which 154 were male and 109 were
female ( X age=19,4905 + 2,5605), that received education in the
schools of physical education and sports of Selcuk University, Inonu
University, Gazi University and Karamanoglu Mehmetbey
University. In order to achieve the purpose of the study, the selfefficacy
scale, which was developed by Jarrusselam and Shwarzer
(1981) [1] and adapted to Turkish by Yesillay (1993) [2], and the
life satisfaction scale, developed by Diener, Emmos, Larsen and
Griffin (1985) [3] and adapted to Turkish by Kokler (1991) [4], were
utilized.For analyzing and interpreting data Kolmogorov-Smirnov
test, t-test and one way anova test were used, while for determining
the difference between the groups Tukey test and Multiple Linear
Regression test were employed and significance was accepted at
P
Abstract: The Cluster Dimension of a network is defined as, which is the minimum cardinality of a subset S of the set of nodes having the property that for any two distinct nodes x and y, there exist the node Si, s2 (need not be distinct) in S such that ld(x,s1) — d(y, s1)1 > 1 and d(x,s2) < d(x,$) for all s E S — {s2}. In this paper, strictly non overlap¬ping clusters are constructed. The concept of LandMarks for Unique Addressing and Clustering (LMUAC) routing scheme is developed. With the help of LMUAC routing scheme, It is shown that path length (upper bound)PLN,d < PLD, Maximum memory space requirement for the networkMSLmuAc(Az) < MSEmuAc < MSH3L < MSric and Maximum Link utilization factor MLLMUAC(i=3) < MLLMUAC(z03) < M Lc
Abstract: Globalisation is a phenomenon that cannot be avoided.
As globalisation allowed free flow of inputs including labour, it may
affect job opportunities for the locals. Therefore, investigate the
determinants of labour supply is essential in understanding the
structure of labour market in the new era of globalization. The
objective of this article is to examine labour supply by taking into
account the globalisation effect. The study covers 3885 households in
Peninsular Malaysia who are chosen using stratified random
sampling. The labour supply model will be the basis for the analysis.
The basic labour supply determinants are own wage and non-labour
income. However, the extended labour supply model incorporates
other variables like spouse wage，number of children and
individuals characteristics like education level and age. Besides, the
globalization indicator will also be incorporated as another
independent variable.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: In order to monitor for traffic traversal, sensors can be
deployed to perform collaborative target detection. Such a sensor
network achieves a certain level of detection performance with the
associated costs of deployment and routing protocol. This paper
addresses these two points of sensor deployment and routing algorithm
in the situation where the absolute quantity of sensors or total energy
becomes insufficient. This discussion on the best deployment system
concluded that two kinds of deployments; Normal and Power law
distributions, show 6 and 3 times longer than Random distribution in
the duration of coverage, respectively. The other discussion on routing
algorithm to achieve good performance in each deployment system
was also addressed. This discussion concluded that, in place of the
traditional algorithm, a new algorithm can extend the time of coverage
duration by 4 times in a Normal distribution, and in the circumstance
where every deployed sensor operates as a binary model.
Abstract: The Resource-Constrained Project Scheduling
Problem (RCPSP) is concerned with single-item or small batch
production where limited resources have to be allocated to dependent
activities over time. Over the past few decades, a lot of work has
been made with the use of optimal solution procedures for this basic
problem type and its extensions. Brucker and Knust[1] discuss, how
timetabling problems can be modeled as a RCPSP. Authors discuss
high school timetabling and university course timetabling problem as
an example. We have formulated two mathematical formulations of
course timetabling problem in a new way which are the prototype of
single-mode RCPSP. Our focus is to show, how course timetabling
problem can be transformed into RCPSP. We solve this
transformation model with genetic algorithm.
Abstract: This article provides a comparative analysis of poetries of diverse nations around the world while largely focusing on Kazakh lyric poetry (Kazakh zhyraulyq oneri). Alongside, it sheds the light to the historical development and contemporary progress path of foremost poetry school located along the Syr Darya coast. Hereby, it-s content and central motives are examined.
Abstract: The aim of this study was to investigate ammonium
exchange capacity of natural and activated clinoptilolite from
Kwazulu-Natal Province, South Africa. X – ray fluorescence (XRF)
analysis showed that the clinoptilolite contained exchangeable ions
of sodium, potassium, calcium and magnesium. This analysis also
confirmed that the zeolite sample had a high silicon composition
compared to aluminium. Batch equilibrium studies were performed
in an orbital shaker and the data fitted the Langmuir isotherm very
well. The ammonium exchange capacity was found to increase with
pH and temperature. Clinoptilolite functionalization with
hydrochloric acid increased its ammonia uptake ability.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: By analyzing the sources of energy and power
loss in PWM (Pulse Width Modulation) controlled drivers of
water electrolysis cells, it is possible to reduce the power
dissipation and enhance the efficiency of such hydrogen
production units. A PWM controlled power driver is based on
a semiconductor switching element where its power
dissipation might be a remarkable fraction of the total power
demand of an electrolysis system. Power dissipation in a
semiconductor switching element is related to many different
parameters which could be fitted into two main categories:
switching losses and conduction losses. Conduction losses are
directly related to the built, structure and capabilities of a
switching device itself and indeed the conditions in which the
element is handling the switching application such as voltage,
current, temperature and of course the fabrication technology.
On the other hand, switching losses have some other
influencing variables other than the mentioned such as control
system, switching method and power electronics circuitry of
the PWM power driver. By analyzings the characteristics of
recently developed power switching transistors from different
families of Bipolar Junction Transistors (BJT), Metal Oxide
Semiconductor Field Effect Transistors (MOSFET) and
Insulated Gate Bipolar Transistors (IGBT), some
recommendations are made in this paper which are able to
lead to achieve higher hydrogen production efficiency by
utilizing PWM controlled water electrolysis cells.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: In this paper we present an extension to Vision Based
LRTA* (VLRTA*) known as Vision Based Moving Target Search
(VMTS) for capturing unknown moving target in unknown territory
with randomly generated obstacles. Target position is unknown to the
agents and they cannot predict its position using any probability
method. Agents have omni directional vision but can see in one
direction at some point in time. Agent-s vision will be blocked by the
obstacles in the search space so agent can not see through the
obstacles. Proposed algorithm is evaluated on large number of
scenarios. Scenarios include grids of sizes from 10x10 to 100x100.
Grids had obstacles randomly placed, occupying 0% to 50%, in
increments of 10%, of the search space. Experiments used 2 to 9
agents for each randomly generated maze with same obstacle ratio.
Observed results suggests that VMTS is effective in locate target
time, solution quality and virtual target. In addition, VMTS becomes
more efficient if the number of agents is increased with proportion to
obstacle ratio.
Abstract: The massive proliferation of affordable computers, Internet broadband connectivity and rich education content has created a global phenomenon in which information and communication technology (ICT) is being used to transform education. Therefore, there is a need to redesign the educational system to meet the needs better. The advent of computers with sophisticated software has made it possible to solve many complex problems very fast and at a lower cost. This paper introduces the characteristics of the current E-Learning and then analyses the concept of cloud computing and describes the architecture of cloud computing platform by combining the features of E-Learning. The authors have tried to introduce cloud computing to e-learning, build an e-learning cloud, and make an active research and exploration for it from the following aspects: architecture, construction method and external interface with the model.
Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.