Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: The notion of intuitionistic fuzzy sets was introduced
by Atanassov as a generalization of the notion of fuzzy sets. Y.B. Jun
and S.Z. Song introduced the notion of intuitionistic fuzzy points.
In this paper we find some relations between the intuitionistic fuzzy
ideals of a semigroup S and the set of all intuitionistic fuzzy points
of S.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Modeling and vibration of a flexible link manipulator
with tow flexible links and rigid joints are investigated which can
include an arbitrary number of flexible links. Hamilton principle and
finite element approach is proposed to model the dynamics of
flexible manipulators. The links are assumed to be deflection due to
bending. The association between elastic displacements of links is
investigated, took into account the coupling effects of elastic motion
and rigid motion. Flexible links are treated as Euler-Bernoulli beams
and the shear deformation is thus abandoned. The dynamic behavior
due to flexibility of links is well demonstrated through numerical
simulation. The rigid-body motion and elastic deformations are
separated by linearizing the equations of motion around the rigid
body reference path. Simulation results are shown on for both
position and force trajectory tracking tasks in the presence of varying
parameters and unknown dynamics remarkably well. The proposed
method can be used in both dynamic simulation and controller
design.
Abstract: The article presents the whole model of IS/IT
architecture exception governance. As first, the assumptions of
presented model are set. As next, there is defined a generic
governance model that serves as a basis for the architecture exception
governance. The architecture exception definition and its attributes
follow. The model respects well known approaches to the area that
are described in the text, but it adopts higher granularity in
description and expands the process view with all the next necessary
governance components as roles, principles and policies, tools to
enable the implementation of the model into organizations. The
architecture exception process is decomposed into a set of processes
related to the architecture exception lifecycle consisting of set of
phases and architecture exception states. Finally, there is information
about my future research related to this area.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: Bacterial cellulose, a biopolysaccharide, is produced by the bacterium, Gluconacetobacter xylinus. Static batch fermentation for bacterial cellulose production was studied in sucrose and date syrup solutions (Bx. 10%) at 28 °C using G. xylinus (PTCC, 1734). Results showed that the maximum yields of bacterial cellulose (BC) were 4.35 and 1.69 g/l00 ml for date syrup and sucrose medium after 336 hours fermentation period, respectively. Comparison of FTIR spectrum of cellulose with BC indicated appropriate coincidence which proved that the component produced by G. xylinus was cellulose. Determination of the area under X-ray diffractometry patterns demonstrated that the crystallinity amount of cellulose (83.61%) was more than that for the BC (60.73%). The scanning electron microscopy imaging of BC and cellulose were carried out in two magnifications of 1 and 6K. Results showed that the diameter ratio of BC to cellulose was approximately 1/30 which indicated more delicacy of BC fibers relative to cellulose.
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: Markov games are a generalization of Markov
decision process to a multi-agent setting. Two-player zero-sum
Markov game framework offers an effective platform for designing
robust controllers. This paper presents two novel controller design
algorithms that use ideas from game-theory literature to produce
reliable controllers that are able to maintain performance in presence
of noise and parameter variations. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. Our approach
generates an optimal control policy for the agent (controller) via a
simple Linear Program enabling the controller to learn about the
unknown environment. The controller is facing an unknown
environment, and in our formulation this environment corresponds to
the behavior rules of the noise modeled as the opponent. Proposed
controller architectures attempt to improve controller reliability by a
gradual mixing of algorithmic approaches drawn from the game
theory literature and the Minimax-Q Markov game solution
approach, in a reinforcement-learning framework. We test the
proposed algorithms on a simulated Inverted Pendulum Swing-up
task and compare its performance against standard Q learning.
Abstract: Method of determining of moisture diffusivity on two types of autoclaved aerated concretes with different bulk density is represented in the paper. On the specimens were measured one dimensional water transport only on liquid phase. Ever evaluation was done from moisture profiles measured in specific times by capacitance moisture meter. All values from capacitance meter were recalculated to moisture content by mass. Moisture diffusivity was determined in dependence on both moisture and temperature. The experiment temperatures were set at values 55, 65, 75 and 85°C.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: This paper proposes the novel model order
formulation scheme to design a discrete PID controller for higher
order linear time invariant discrete systems. Modified PSO (MPSO)
based model order formulation technique has used to obtain the
successful formulated second order system. PID controller is tuned to
meet the desired performance specification by using pole-zero
cancellation and proposed design procedures. Proposed PID
controller is attached with both higher order system and formulated
second order system. System specifications are tabulated and closed
loop response is observed for stabilization process. The proposed
method is illustrated through numerical examples from literature.
Abstract: This paper investigates the relationship between state and business in the context of structural and institutional transformations in Indonesia following the collapse of the New Order regime in 1998. Since 1998, Indonesia has embarked on a shift from an authoritarian to democratic polity and from a centralised to a decentralised system of governance, transforming the country into the third largest democracy and one of the most decentralised states in the world. This paper examines whether the transformation of the Indonesian state has altered the pattern of state and business relations with focus on clientism and corruption as the key dependent variable, and probes how/to what extent this has changed as a result of the transformation and the ensuring shifts in business and state relations. Based on interviews with key government and business actors as well as prominent scholars in Indonesia, it is found that since the demise of the New Order, business associations in Indonesia have become more independent of state control and more influential in public decision-making whereas the government has become more responsive of business concerns and more committed to combat corruption and clientism. However, these changes have not necessarily rendered business people completely leave individualclientelistic relationship with the government, and simply pursue wider sectoral and business-wide collectivism as an alternative way of channelling their aspirations, which is expected to help reduce corruption and clientism in Indonesia. This paper concludes that democratisation and a more open politics may have helped reduce corruption and clientism in Indonesia through changes in government. However, it is still difficult to imply that such political transformation has fostered business collective action and a broader, more encompassing pattern of business lobbying and activism, which is expected to help reduce corruption and clientism.
Abstract: This study investigates the use of genetic algorithms
in information retrieval. The method is shown to be applicable to
three well-known documents collections, where more relevant
documents are presented to users in the genetic modification. In this
paper we present a new fitness function for approximate information
retrieval which is very fast and very flexible, than cosine similarity
fitness function.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: The major challenge faced by wireless sensor networks is security. Because of dynamic and collaborative nature of sensor networks the connected sensor devices makes the network unusable. To solve this issue, a trust model is required to find malicious, selfish and compromised insiders by evaluating trust worthiness sensors from the network. It supports the decision making processes in wireless sensor networks such as pre key-distribution, cluster head selection, data aggregation, routing and self reconfiguration of sensor nodes. This paper discussed the kinds of trust model, trust metrics used to address attacks by monitoring certain behavior of network. It describes the major design issues and their countermeasures of building trust model. It also discusses existing trust models used in various decision making process of wireless sensor networks.
Abstract: The nonlinear chaotic non-autonomous fourth order
system is algebraically simple but can generate complex chaotic
attractors. In this paper, non-autonomous fourth order chaotic
oscillator circuits were designed and simulated. Also chaotic nonautonomous
Attractor is addressed suitable for chaotic masking
communication circuits using Matlab® and MultiSIM® programs.
We have demonstrated in simulations that chaos can be synchronized
and applied to signal masking communications. We suggest that this
phenomenon of chaos synchronism may serve as the basis for little
known chaotic non-autonomous Attractor to achieve signal masking
communication applications. Simulation results are used to visualize
and illustrate the effectiveness of non-autonomous chaotic system in
signal masking. All simulations results performed on nonautonomous
chaotic system are verify the applicable of secure
communication.