Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: In field of Computer Science and Mathematics,
sorting algorithm is an algorithm that puts elements of a list in a
certain order i.e. ascending or descending. Sorting is perhaps the
most widely studied problem in computer science and is frequently
used as a benchmark of a system-s performance. This paper
presented the comparative performance study of four sorting
algorithms on different platform. For each machine, it is found that
the algorithm depends upon the number of elements to be sorted. In
addition, as expected, results show that the relative performance of
the algorithms differed on the various machines. So, algorithm
performance is dependent on data size and there exists impact of
hardware also.
Abstract: This Paper presents an on-going research in the area of Model-Driven Engineering (MDE). The premise is that UML is too unwieldy to serve as the basis for model-driven engineering. We need a smaller, simpler notation with a cleaner semantics. We propose some ideas for a simpler notation with a clean semantics. The result is known as μML, or the Micro-Modelling Language.
Abstract: Tubular process equipment is often damaged in
industrial processes. The damage occurs both on devices working at
high temperatures and also on less exposed devices. In case of sudden
damage of key equipment a shutdown of the whole production unit
and resulting significant economic losses are imminent. This paper
presents a solution of several types of tubular process equipment. The
causes of damage and suggestions of correction actions are discussed
in all cases. Very important part is the analysis of operational
conditions, determination of unfavourable working states decreasing
lifetime of devices and suggestions of correction actions. Lately very
popular numerical methods are used for analysis of the equipment.
Abstract: Due to its geographical location, Iran is considered one of the earthquake-prone areas where the best way to decrease earthquake effects is supposed to be strengthening the buildings. Even though, one idea suggests that the use of adobe in constructing buildings be prohibited for its weak function especially in earthquake-prone areas, however, regarding ecological considerations, sustainability and other local skills, another idea pays special attention to adobe as one of the construction technologies which is popular among people. From the architectural and technological point of view, as strong sustainable building construction materials, compressed adobe construction materials make most of the construction in urban or rural areas ranging from small to big industrial buildings used to replace common earth blocks in traditional systems and strengthen traditional adobe buildings especially against earthquake. Mentioning efficient construction using compressed adobe system as a reliable replacement for traditional soil construction materials , this article focuses on the experiences of India in the fields of sustainable development of compressed adobe systems in the form of system in which the compressed soil is combined with cement, load bearing building with brick/solid concrete block system, brick system using rat trap bond, metal system with adobe infill and finally emphasizes on the use of these systems in the earthquake-struck city of Bam in Iran.
Abstract: A process flowsheet was developed in ChemCad 6.4
to study the effect of feed moisture contents on the pre-esterification
of waste oils. Waste oils were modelled as a mixture of triolein
(90%), oleic acid (5%) and water (5%). The process mainly consisted
of feed drying, pre-esterification reaction and methanol recovery. The
results showed that the process energy requirements would be
minimized when higher degrees of feed drying and higher preesterification
reaction temperatures are used.
Abstract: The frontal area in the brain is known to be involved in
behavioral judgement. Because a Kanji character can be discriminated
visually and linguistically from other characters, in Kanji character
discrimination, we hypothesized that frontal event-related potential
(ERP) waveforms reflect two discrimination processes in separate
time periods: one based on visual analysis and the other based
on lexcical access. To examine this hypothesis, we recorded ERPs
while performing a Kanji lexical decision task. In this task, either a
known Kanji character, an unknown Kanji character or a symbol was
presented and the subject had to report if the presented character was
a known Kanji character for the subject or not. The same response
was required for unknown Kanji trials and symbol trials. As a preprocessing
of signals, we examined the performance of a method
using independent component analysis for artifact rejection and found
it was effective. Therefore we used it. In the ERP results, there
were two time periods in which the frontal ERP wavefoms were
significantly different betweeen the unknown Kanji trials and the
symbol trials: around 170ms and around 300ms after stimulus onset.
This result supported our hypothesis. In addition, the result suggests
that Kanji character lexical access may be fully completed by around
260ms after stimulus onset.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: This paper proposes a bi-objective model for the
facility location problem under a congestion system. The idea of the
model is motivated by applications of locating servers in bank
automated teller machines (ATMS), communication networks, and so
on. This model can be specifically considered for situations in which
fixed service facilities are congested by stochastic demand within
queueing framework. We formulate this model with two perspectives
simultaneously: (i) customers and (ii) service provider. The
objectives of the model are to minimize (i) the total expected
travelling and waiting time and (ii) the average facility idle-time.
This model represents a mixed-integer nonlinear programming
problem which belongs to the class of NP-hard problems. In addition,
to solve the model, two metaheuristic algorithms including nondominated
sorting genetic algorithms (NSGA-II) and non-dominated
ranking genetic algorithms (NRGA) are proposed. Besides, to
evaluate the performance of the two algorithms some numerical
examples are produced and analyzed with some metrics to determine
which algorithm works better.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: Currently, many types of no-reversible compressed
sound source, represented by MP3 (MPEG Audio Layer-3) are
popular in the world and they are widely used to make the music file
size smaller. The sound data created in this way has less information as
compared to pre-compressed data. The objective of this study is by
analyzing EEG to determine if people can recognize such difference as
differences in sound. A measurement system that can measure and
analyze EEG when a subject listens to music were experimentally
developed. And ten subjects were studied with this system. In this
experiment, a WAVE formatted music data and a MP3 compressed
music data that is made from the WAVE formatted data were
prepared. Each subject was made to hear these music sources at the
same volume. From the results of this experiment, clear differences
were confirmed between two wound sources.
Abstract: Simulations play a major role in education not only because they provide realistic models with which students can interact to acquire real world experiences, but also because they constitute safe environments in which students can repeat processes without any risk in order to perceive easier concepts and theories. Virtual reality is widely recognized as a significant technological advance that can facilitate learning process through the development of highly realistic 3D simulations supporting immersive and interactive features. The objective of this paper is to analyze the influence of virtual reality-s use in chemistry instruction as well as to present an integrated web-based learning environment for the simulation of chemical experiments. The proposed application constitutes a cost-effective solution for both schools and universities without appropriate infrastructure and a valuable tool for distance learning and life-long education in chemistry. Its educational objectives are the familiarization of students with the equipment of a real chemical laboratory and the execution of virtual volumetric analysis experiments with the active participation of students.
Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: This paper deals with the design of a moving sliding
surface in a variable structure plant for a second order system. The
chattering phenomena is also dealt with during the switching process
for an unstable sliding surface condition. The simulation examples
considered in this paper shows the effectiveness of the sliding mode
control method used for the design of the moving sliding surfaces. A
simulink model of the continuous system was also developed in
MATLAB-SIMULINK for the design and hence demonstrated. The
phase portraits and the state plots shows the demonstration of
the powerful control technique which can be applied for second
order systems.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.
Abstract: The argument that self-disclosure will change the
psychoanalytic process into a socio-cultural niche distorting the
therapeutic alliance and compromise therapeutic effectiveness is still
the widely held belief amongst many psychotherapists. This paper
considers the issues surrounding culture, disclosure and concealment
since they remain largely untheorized and clinically problematic. The
first part of the paper will critically examine the theory and practice
of psychoanalysis across cultures, and explore the reasons for
culturally diverse patients to conceal rather than disclose their
feelings and thoughts in the transference. This is followed by a
discussion on how immigrant analysts- anonymity is difficult to
maintain since diverse nationalities, language and accents provide
clues to the therapist-s and patient-s origins. Through personal
clinical examples of one the author-s (who is an immigrant) the paper
analyses the transference-countertransference paradigm and how it
reflects in the analyst-s self-revelation.
Abstract: In this paper we are to find the optimum multiwavelet for compression of electrocardiogram (ECG) signals and then, selecting it for using with SPIHT codec. At present, it is not well known which multiwavelet is the best choice for optimum compression of ECG. In this work, we examine different multiwavelets on 24 sets of ECG data with entirely different characteristics, selected from MIT-BIH database. For assessing the functionality of the different multiwavelets in compressing ECG signals, in addition to known factors such as Compression Ratio (CR), Percent Root Difference (PRD), Distortion (D), Root Mean Square Error (RMSE) in compression literature, we also employed the Cross Correlation (CC) criterion for studying the morphological relations between the reconstructed and the original ECG signal and Signal to reconstruction Noise Ratio (SNR). The simulation results show that the Cardinal Balanced Multiwavelet (cardbal2) by the means of identity (Id) prefiltering method to be the best effective transformation. After finding the most efficient multiwavelet, we apply SPIHT coding algorithm on the transformed signal by this multiwavelet.
Abstract: The aim of this paper is to investigate the
performance of the developed two point block method designed for
two processors for solving directly non stiff large systems of higher
order ordinary differential equations (ODEs). The method calculates
the numerical solution at two points simultaneously and produces
two new equally spaced solution values within a block and it is
possible to assign the computational tasks at each time step to a
single processor. The algorithm of the method was developed in C
language and the parallel computation was done on a parallel shared
memory environment. Numerical results are given to compare the
efficiency of the developed method to the sequential timing. For
large problems, the parallel implementation produced 1.95 speed-up
and 98% efficiency for the two processors.