Abstract: This paper presents the experimental results of high-density polyethylene cable spacers for 22 kV distribution systems under salt water dip wheel test based on IEC 62217. The strength of anti-tracking and anti-erosion of cable spacer surface was studied in this study. During the test, dry band arc and corona discharge were observed on cable spacer surface. After 30,000 cycles of salt water dip wheel test, obviously surface erosion and tracking were observed especially on the ground end. Chemical analysis results by fourier transforms infrared spectroscopy showed chemical changed from oxidation and carbonization reaction on tested cable spacer. Increasing of C=O and C=C bonds confirmed occurrence of these reactions.
Abstract: Management is required to understand all information security risks within an organization, and to make decisions on which information security risks should be treated in what level by allocating how much amount of cost. However, such decision-making is not usually easy, because various measures for risk treatment must be selected with the suitable application levels. In addition, some measures may have objectives conflicting with each other. It also makes the selection difficult. Moreover, risks generally have trends and it also should be considered in risk treatment. Therefore, this paper provides the extension of the model proposed in the previous study. The original model supports the selection of measures by applying a combination of weighted average method and goal programming method for multi-objective analysis to find an optimal solution. The extended model includes the notion of weights to the risks, and the larger weight means the priority of the risk.
Abstract: The work involves develops attended by a numerical
execution of the eXtend Finite Element Method premises a
measurement by the fracture process cracked so many cracked plates
an application will be processed for the calculation of the stress
intensity factor SIF. In the first we give in statically part the
distribution of stress, displacement field and strain of composite plate
in two cases uncrack/edge crack, also in dynamical part the first six
modes shape. Secondly, we calculate Stress Intensity Factor SIF for
different orientation angle θ of central crack with length (2a=0.4mm)
in plan strain condition, KI and KII are obtained for mode I and mode
II respectively using X-FEM method. Finally from crack inclined
involving mixed modes results, the comparison we chose dangerous
inclination and the best crack angle when K is minimal.
Abstract: The purpose of this study was to determine the significance of history of obesity for the development of childhood overweight and/or obesity. Accordingly, a systematic literature review of English-language studies published from 1980 to 2012 using the following data bases: MEDLINE, PsychINFO, Cochrane Database of Systematic Reviews, and Dissertation Abstracts International was conducted. The following terms were used in the search: pregnancy, overweight, obesity, family history, parents, childhood, risk factors. Eleven studies of family history and obesity conducted in Europe, Asia, North America, and South America met the inclusion criteria. A meta-analysis of these studies indicated that family history of obesity is a significant risk factor of overweight and /or obesity in offspring; risk for offspring overweight and/or obesity associated with family history varies depending of the family members included in the analysis; and when family history of obesity is present, the offspring are at greater risk for developing obesity or overweight. In addition, the results from moderator analyses suggest that part of the heterogeneity discovered between the studies can be explained by the region of world that the study occurred in and the age of the child at the time of weight assessment.
Abstract: Game addiction has become an extremely important topic in psychology researchers, particularly in understanding and explaining why individuals become addicted (to video games). In previous studies, effect of online game addiction on social responsibilities, health problems, government action, and the behaviors of individuals to purchase and the causes of making individuals addicted on the video games has been discussed. Extending these concepts in marketing, it could be argued than the phenomenon could enlighten and extending our understanding on consumer loyalty. This study took the Grounded Theory approach, and found that motivation, satisfaction, fulfillments, exploration and achievements to be part of the important elements that builds consumer loyalty.
Abstract: This paper presents the experimental results on role of
ionic solutions affect water treeing propagation in cross-linked
polyethylene insulation for high voltage cable. To study the water
treeing expansion due to the ionic solutions, discs of 4mm thickness
and 4cm diameter were taken from 115 kV XLPE insulation cable
and were used as test specimen in this study. Ionic solutions
composed of CuSO4, FeSO4, Na2SO4 and K2SO4 were used. Each
specimen was immersed in 0.1 mole ionic solutions and was tested
for 120 hrs. under a voltage stress at 7 kV AC rms, 1000 Hz. The
results show that Na2SO4 and CuSO4solutions play an important role
in the expansion of water treeing and cause degradation of the crosslinked
polyethylene (XLPE) in the presence of the applied electric
field.
Abstract: Natural dye extracted from Caesalpinia sappan Linn. was applied to a cotton fabric and silk yarn by dyeing process. The dyestuff component of Caesalpinia sappan Linn. was extracted using water and ethanol. Analytical studies such as UV–VIS spectrophotometry and gravimetric analysis were performed on the extracts. Brazilein, the major dyestuff component of Caesalpinia sappan Linn. was confirmed in both aqueous and ethanolic extracts by UV–VIS spectrum. The color of each dyed material was investigated in terms of the CIELAB (L*, a* and b*) and K/S values. Cotton fabric dyed without mordant had a shade of reddish-brown, while those post-mordanted with aluminum potassium sulfate, ferrous sulfate and copper sulfate produced a variety of wine red to dark purple color shades. Cotton fabric and silk yarn dyeing was studied using aluminum potassium sulfate as a mordant. The observed color strength was enhanced with increase in mordant concentration.
Abstract: We describe a relationship between integral images and
differential images. First, we derive a simple difference filter from
conventional integral image. In the derivation, we show that an
integral image and the corresponding differential image are related
to each other by simultaneous linear equations, where the numbers
of unknowns and equations are the same, and therefore, we can
execute the integration and differentiation by solving the simultaneous
equations. We applied the relationship to an image fusion problem,
and experimentally verified the effectiveness of the proposed method.
Abstract: Emission regulations for diesel engines are being strengthened and it is impossible to meet the standards without exhaust after-treatment systems. Lack of the space in many diesel vehicles, however, make it difficult to design and install stand-alone catalytic converters such as DOC, DPF, and SCR in the vehicle exhaust systems. Accordingly, those have been installed inside the muffler to save the space, and referred to the catalytic muffler. However, that has complex internal structure with perforated plate and pipe for noise and monolithic catalyst for emission reduction. For this reason, flow uniformity and pressure drop, which affect efficiency of catalyst and engine performance, respectively, should be examined when the catalytic muffler is designed. In this work, therefore, the flow uniformity and pressure drop to improve the performance of the catalytic converter and the engine have been numerically investigated by changing various design parameters such as inlet shape, porosity, and outlet shape of the muffler using the three-dimensional turbulent flow of the incompressible, non-reacting, and steady state inside the catalytic muffler. Finally, it can be found that the shape, in which the muffler has perforated pipe inside the inlet part, has higher uniformity index and lower pressure drop than others considered in this work.
Abstract: The concept of competitiveness is currently very
frequently used term. However, the interpretation of its essence is
different. In this paper, one of the many concepts of competitiveness
will be analyzed and that is macroeconomic competitiveness, which
is understood as a process, which is based on the productivity growth
through the growth of key macroeconomic indicators such as
standards of living and employment, where all of these variables
must have a sustainable basis. Given the competition is a relative
quantity it must be constantly compared with the development of
competitiveness in other economies or regions. And this comparison
method is also used in the article that compares the macrocompetitiveness
of selected economies of the European Economic
Area – the Czech Republic, Poland, Austria, Switzerland and
Germany. The aim of the paper is to verify the hypothesis concerning
the direct correlation between the size of the economy and its
competitiveness.
Abstract: The consolidation of the European Higher Education Area (EHEA) in universities has led to significant changes in student training. This paper, part of a Teaching Innovation Project, starts from new training requirements that are fit within Undergraduate Thesis Project, a subject that culminate student learning. Undergraduate Thesis Project is current assessment system that weigh the student acquired training in university education. Students should develop a range of cross curricular competences such as public presentation of ideas, problems and solutions both orally and writing in Undergraduate Thesis Project. Specifically, we intend with our innovation proposal to provide resources that enable university students from Teacher Degree in Education Faculty of University of Extremadura (Spain) to develop the cross curricular competence of public speaking.
Abstract: The external flow simulation of a flying car at take off phase is a daunting task owing to the fact that the prediction of the transient unsteady flow features during its deployment phase is very complex. In this paper 3D numerical simulations of external flow of Ferrari F430 proposed flying car with different NACA 9618 rectangular wings have been carried. Additionally, the aerodynamics characteristics have been generated for optimizing its geometry for achieving the minimum take off velocity with better overall performance in both road and air. The three-dimensional standard k-omega turbulence model has been used for capturing the intrinsic flow physics during the take off phase. In the numerical study, a fully implicit finite volume scheme of the compressible, Reynolds-Averaged, Navier-Stokes equations is employed. Through the detailed parametric analytical studies we have conjectured that Ferrari F430 flying car facilitated with high wings having three different deployment histories during the take off phase is the best choice for accomplishing its better performance for the commercial applications.
Abstract: Optimization of business processes in trading companies is reviewed in the report. There is the presentation of the “Wholesale Customer Order Handling Process” business process model applicable for small and medium businesses. It is proposed to apply the algorithm for automation of the customer order processing which will significantly reduce labor costs and time expenditures and increase the profitability of companies. An optimized business process is an element of the information system of accounting of spare parts trading network activity. The considered algorithm may find application in the trading industry as well.
Abstract: The article describes an approach to build competence in research of Bachelor and Master, which is now an important feature of modern specialist in the field of engineering. We provide an example of methodical teaching methods with the research aspect, including the formulation of the problem, the method of conducting experiments, analysis of the results. Implementation of methods allows the student to better consolidate their knowledge and skills at the same time to get research. Knowledge on the part of the media requires some training in the subject area and teaching methods.
Abstract: Several yield-based stress indices have been developed that may be more applicable to work on drought tolerance. In this study, we investigate possibility of using stress susceptibility index (SSI), tolerance index (TOL), yield stability index (YSI), yield index (YI), stress tolerance index (STI), geometric mean productivity (GMP), harmonic mean (HARM), mean productivity (MP) to identify genotypic performance of some maize cultivars under normal and stressed condition. The results indicate that it was possible to identify superior genotypes for drought tolerance based on their stress indices and generally SSI indices which showed the lowest negative correlation with dry matter yield can be used as the best index for maize breeding programs to introduce drought tolerant hybrids. It was found that SC 647 showed the best behavior under drought stress condition based on TOL and SSI. A higher STI, GMP, and HARM values were attained for ko6. It can be suggested that ko6 should be cultivated in moderate stressful environment of Iran.
Abstract: In this study was performed in situ consolidation of polypropylene matrix/glass reinforced roving by combining heating systems and roll pressing. The commingled roving during hoop winding was winded on a cylindrical mandrel. The work also presents the advances made in the processing of these materials into composites by conventional technique filament winding. Experimental studies were performed with changing parameters – temperature, pressure and speed. Finally, it describes the investigation of the optimal processing conditions that maximize the mechanical properties of the composites. These properties are good enough for composites to be used as engineering materials in many structural applications.
Abstract: Undoubtedly one of the most far-reaching and
controversial topics considered in the past few decades, has been
globalization. Globalization lies in the essence of the modern culture.
It is a complex and rapidly expanding network of links and mutual
interdependence that is an aspect of modern life; though some argue
that this link existed since the beginning of human history. If we
consider globalization as a dynamic social process in which the
geographical constraints governing the political, economic, social and
cultural relationships have been undermined, it might not be possible
to simply describe its impact on the urban fabric. But since in this
phenomenon the increase in communications of societies (while
preserving the main cultural - regional characteristics) with one
another and the increase in the possibility of influencing other
societies are discussed, the need for more studies will be felt. The
main objective of this study is to grade based on some globalization
factors on urban fabric applying the TOPSIS model. The research
method is descriptive - analytical and survey. For data analysis, the
TOPSIS model and SPSS software were used and the results of GIS
software with fourteen cities are shown on the map. The results show
that the process of being influenced by the globalization of the urban
fabric of fourteen zones of Isfahan was not similar and there have
been large differences in this respect between city zones; the most
affected areas are zones 5, 6 and 9 of the municipality and the least
impact has been on the zones 4 and 3 and 2.
Abstract: River flow over micro hydro power (MHP) turbines of multiple arrays arrangement is simulated with computational fluid dynamics (CFD) software to obtain the flow characteristics. In this paper, CFD software is used to simulate the water flow over MHP turbines as they are placed in a river. Multiple arrays arrangement of MHP turbines lead to generate large amount of power. In this study, a river model is created and simulated in CFD software to obtain the water flow characteristic. The process then continued by simulating different types of arrays arrangement in the river model. A MHP turbine model consists of a turbine outer body and static propeller blade in it. Five types of arrangements are used which are parallel, series, triangular, square and rhombus with different spacing sizes. The velocity profiles on each MHP turbines are identified at the mouth of each turbine bodies. This study is required to obtain the arrangement with increasing spacing sizes that can produce highest power density through the water flow variation.
Abstract: Diabetic retinopathy is characterized by the development of retinal microaneurysms. The damage can be prevented if disease is treated in its early stages. In this paper, we are comparing Support Vector Machine (SVM) and Naïve Bayes (NB) classifiers for automatic microaneurysm detection in images acquired through non-dilated pupils. The Nearest Neighbor classifier is used as a baseline for comparison. Detected microaneurysms are validated with expert ophthalmologists’ hand-drawn ground-truths. The sensitivity, specificity, precision and accuracy of each method are also compared.
Abstract: Adolescence is a neuralgic stage in the formation of every human being, generally at this stage is when the middle school level is studied. In 2006 in Mexico incorporated “mentoring" space to assist students in their integration and participation in life. In public middle schools, is sometimes difficult to be aware of situations that affect students because of the number of them and traditional records management. Whit this they lose the opportunity to provide timely support as a preventive way. In order to provide this support, it is required to know the students by detecting the relevant information that has greater impact on their learning process. This research is looking to check if it is possible to identify student’s relevant information to detect when it is at risk, and then to propose a model to manage in a proper way such information.