Abstract: In Algeria, the conditioning units of dates, generate
significant quantities of waste arising from sorting deviations. This
biomass, until then considered as a waste with high impact on the
environment can be transformed into high value added product. It is
possible to develop common dates of low commercial value, and put
on the local and international market a new generation of products
with high added values such as bio ethanol. Besides its use in
chemical synthesis, bio ethanol can be blended with gasoline to
produce a clean fuel while improving the octane.
Abstract: The purpose of this study is to propose an effective method to improve frictional coefficient between shoe rubber soles with added glass fibers and the surfaces of icy and snowy road in order to prevent slip-and-fall accidents by the users. The additional fibers into the rubber were uniformly tilted to the perpendicular direction of the frictional surface, where tilting angles were -60, -30, +30, +60, 90 degrees and 0 (as normal specimen), respectively. It was found that parallel arraignment was effective to improve the frictional coefficient when glass fibers were embedded in the shoe rubber, while perpendicular to normal direction of the embedded glass fibers on the shoe surface was also effective to do that once after they were exposed from the shoe rubber with its abrasion. These improvements were explained by the increase of stiffness against the shear deformation of the rubber at critical frictional state and adequate scratching of fibers when fibers were protruded in perpendicular to frictional direction, respectively. Most effective angle of tilting of frictional coefficient between rubber specimens and a stone was perpendicular (= 0 degree) to frictional direction. Combinative modified rubber specimen having 2 layers was fabricated where tilting angle of protruded fibers was 0 degree near the contact surface and tilting angle of embedded fibers was 90 degrees near back surface in thickness direction to further improve the frictional coefficient. Current study suggested that effective arraignments in tilting angle of the added fibers should be applied in designing rubber shoe soles to keep the safeties for users in regions of cold climates.
Abstract: Rotary entrainment is a phenomenon in which the
interface of two immiscible fluids are subjected to external flux by
means of rotation. Present work reports the experimental study on
rotary motion of a horizontal cylinder between the interface of air and
water to observe the penetration of gas inside the liquid. Experiments
have been performed to establish entrainment of air mass in water
alongside the cylindrical surface. The movement of tracer and seeded
particles has been tracked to calculate the speed and path of the
entrained air inside water. Simplified particle image velocimetry
technique has been used to trace the movement of particles/tracers at
the moment they are injected inside the entrainment zone and
suspended beads have been used to replicate the particle movement
with respect to time in order to determine the flow dynamics of the
fluid along the cylinder. Present paper establishes a thorough experimental analysis of the
rotary entrainment phenomenon between air and water keeping in
interest the extent to which we can intermix the two and also to study
its entrainment trajectories.
Abstract: In this paper, we have reported birefringence
manipulation in regenerated high birefringent fiber Bragg grating
(RPMG) by using CO2 laser annealing method. The results indicate
that the birefringence of RPMG remains unchanged after CO2 laser
annealing followed by slow cooling process, but reduced after fast
cooling process (~5.6×10-5). After a series of annealing procedures
with different cooling rates, the obtained results show that slower the
cooling rate, higher the birefringence of RPMG. The volume, thermal
expansion coefficient (TEC) and glass transition temperature (Tg)
change of stress applying part in RPMG during cooling process are
responsible for the birefringence change. Therefore, these findings
are important to the RPMG sensor in high and dynamic temperature
environment. The measuring accuracy, range and sensitivity of
RPMG sensor is greatly affected by its birefringence value. This
work also opens up a new application of CO2 laser for fiber annealing
and birefringence modification.
Abstract: The understanding of geotechnical characteristics of
near-surface material and the effects of the groundwater is very
important problem in such as site studies. For showing the relations
between seismic data and groundwater, we selected about 25 km2 as
the study area. It has been presented which is a detailed work of
seismic data and groundwater depths of Gokpinar Damp area.
Seismic waves velocity (Vp and Vs) are very important parameters
showing the soil properties. The seismic records were used the
method of the multichannel analysis of surface waves near area of
Gokpinar Damp area. Sixty sites in this area have been investigated
with survey lines about 60 m in length. MASW (Multichannel
analysis of surface wave) method has been used to generate onedimensional
shear wave velocity profile at locations. These shear
wave velocities are used to estimate equivalent shear wave velocity in
the study area at every 2 and 5 m intervals up to a depth of 45 m.
Levels of equivalent shear wave velocity of soil are used the
classified of the study area. After the results of the study, it must be
considered as components of urban planning and building design of
Gokpinar Damp area, Denizli and the application and use of these
results should be required and enforced by municipal authorities.
Abstract: Unsteady flow and heat transfer from a circular
cylinder in cross-flow is studied numerically. The governing
equations are solved by using finite volume method. Reynolds
number varies in range of 50 to 200; in this range flow is considered
to be laminar and unsteady. Al2O3 nanoparticle with volume fraction
in range of 5% to 20% is added to pure water. Effects of adding
nanoparticle to pure water on lift and drag coefficient and Nusselt
number is presented. Addition of Al2O3 has inconsiderable effect on
the value of drags and lift coefficient. However, it has significant
effect on heat transfer; results show that heat transfer of Al2O3
nanofluid is about 9% to 36% higher than pure water.
Abstract: Monitoring the conditions of rotating machinery, such
as bearings, is important in order to improve the stability of work.
Acoustic Emission (AE) and vibration analysis are some of the most
accomplished techniques used for this purpose. Acoustic emission
has the ability to detect the initial phase of component degradation.
Moreover, it has been observed that vibration analysis is not as
successful at low rotational speeds (below 100 rpm). This because the
energy generated within this speed region is not detectable using
conventional vibration. From this perspective, this paper has
presented a brief review of using acoustic emission techniques for
monitoring bearing conditions.
Abstract: Internship is a supervised and structured learning
experience related to one’s field of study or career goal. Internship
allows students to obtain work experience and the opportunity to
apply skills learned during university. Internship is a valuable
learning experience for students; however, literature on employer
assessment is scarce on Malaysian student’s internship experience.
This study focuses on employer’s perspective on student’s
performances during their three months of internship. The results are
based on the descriptive analysis of 45 sets of question gathered from
the on-site supervisors of the interns. The survey of 45 on-site
supervisor’s feedback was collected through postal mail. It was found
that, interns have not met their on-site supervisor’s expectations in
many areas. The significance of this study is employer’s assessment
on the internship shall be used as feedback to improve on ways how
to prepare students for their internship and employments in future.
Abstract: The report deals with comparison of traffic accidents
in Slovak republic in road and rail transport since 2009 until 2014,
with evaluation of external costs and consequently with the
possibilities of their internalization. The results of road traffic
accidents analysis are realized in line with after-effects they have
caused; in line with main cause, place of origin (within or out of
town) and in accordance to age of accident´s victims and kind of
injuries (easy, hard or fatal). Evaluation of individual after-effects is
carried in terms of probability of traffic accidents occurrence.
Abstract: The present research aimed at studying the awareness
and attitudes of teachers towards inclusive education. The sample
consisted of 60 teachers, teaching in the primary section (1st – 4th) of
regular schools affiliated to the SSC board in Mumbai. Sample was
selected by Multi-stage cluster sampling technique. A semi-structured
self-constructed interview schedule and a self-constructed attitude
scale was used to study the awareness of teachers about disability and
Inclusive education, and their attitudes towards inclusive education
respectively. Themes were extracted from the interview data and
quantitative data was analyzed using SPSS package. Results revealed
that teachers had some amount of awareness but an inadequate
amount of information on disabilities and inclusive education.
Disability to most (37) teachers meant “an inability to do something”.
The difference between disability and handicap was stated by most as
former being cognitive while handicap being physical in nature. With
regard to Inclusive education, a large number (46) stated that they
were unaware of the term and did not know what it meant. Majority
(52) of them perceived maximum challenges for themselves in an
inclusive set up, and emphasized on the role of teacher training
courses in the area of providing knowledge (49) and training in
teaching methodology (53). Although, 83.3% of teachers held a
moderately positive attitude towards inclusive education, a large
percentage (61.6%) of participants felt that being in inclusive set up
would be very challenging for both children with special needs and
without special needs. Though, most (49) of the teachers stated that
children with special needs should be educated in regular classroom
but they further clarified that only those should be in a regular
classroom who have physical impairments of mild or moderate
degree.
Abstract: Selling has changed. Selling has taken on aspects of
relationship marketing and sales force play a critical role in
developing long-term relationships between buyers and sellers which
is seen to serve the company’s targets and create success for a long
run. The purpose of this study was to examine what really matters in
buyer-seller encounters and determine what expectations business
buyers have. We studied 17 business buyers by a qualitative
interview. We found that buyers appreciate encounters where the
salesperson face the buyer as a way he or she is as a person, map the
real needs to improve buyers’ business and build up cooperation for
long-term relationship. This study show that personality matters are a
key elements when satisfying business buyers’ expectations.
Abstract: The research explored the effect of morphemic analysis
awareness on ESL secondary school students’ vocabulary acquisition.
The quasi-experimental study was conducted with 100 ESL
secondary school students in two experimental groups (inflectional
and derivational) and one control group. The students’ vocabulary
acquisition was assessed through two measures: Morph-Analysis Test
and Morph-Vocabulary Test in the pretest and posttest before and
after an intervention programme. Results of ANCOVA revealed that
both the experimental groups achieved a significant score in Morph-
Analysis Test and Vocabulary-Morphemic Test. However, the
inflectional group obtained a fairly higher score than the derivational
group. Thus, the findings of the research are discussed in two main
areas. First, individual instructions of two types of morphemic
awareness have contributed significant results on inflectional and
derivational awareness among the ESL secondary school students.
Nevertheless, derivational morphology achieved a significant but
relatively smaller amount of effect on secondary school students’
morphological awareness compared to inflectional morphology in
this research. Second finding showed that the awareness of
inflectional and derivational morphology was found significantly
related to vocabulary achievement of ESL secondary school students.
Nevertheless, inflectional morphemic awareness had higher
significant effect on ESL secondary school students’ vocabulary
acquisition. Despite these findings, the study implies that morphemic
analysis awareness can serve as an alternative strategy for ESL
secondary school students in acquiring English vocabulary.
Abstract: The Com-Poisson (CMP) model is one of the most
popular discrete generalized linear models (GLMS) that handles
both equi-, over- and under-dispersed data. In longitudinal context,
an integer-valued autoregressive (INAR(1)) process that incorporates
covariate specification has been developed to model longitudinal
CMP counts. However, the joint likelihood CMP function is
difficult to specify and thus restricts the likelihood-based estimating
methodology. The joint generalized quasi-likelihood approach
(GQL-I) was instead considered but is rather computationally
intensive and may not even estimate the regression effects due
to a complex and frequently ill-conditioned covariance structure.
This paper proposes a new GQL approach for estimating the
regression parameters (GQL-III) that is based on a single score vector
representation. The performance of GQL-III is compared with GQL-I
and separate marginal GQLs (GQL-II) through some simulation
experiments and is proved to yield equally efficient estimates as
GQL-I and is far more computationally stable.
Abstract: This paper describes the design and implementation of
a hardware setup for online monitoring of 24 refrigerators inside
blood bank center using the microcontroller and CAN bus for
communications between each node. Due to the security of locations
in the blood bank hall and difficulty of monitoring of each
refrigerator separately, this work proposes a solution to monitor all
the blood bank refrigerators in one location. CAN-bus system is used
because it has many applications and advantages, especially for this
system due to easy in use, low cost, providing a reduction in wiring,
fast to repair and easily expanding the project without a problem.
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.
Abstract: It is very important for a developing nation to
developing their infrastructure on the prime priority because their
infrastructure particularly their roads and transportation functions as a
blood in the system. Almost 1.1 billion populations share the travel
and transportation industry in India. On the other hand, the Pakistan
transportation industry is also extensive and elevating about 170
million users of transportation. Indian and Pakistani specifically
within bus industry are well connected within and between the urban
and rural areas. The transportation industry is radically helping the
economic alleviation of both countries. Due to high economic
instability, unemployment and poverty rate both countries
governments are very serious and committed to help for boosting
their economy. They believe that any form of transportation
development would play a vital role in the development of land,
infrastructure which could indirectly support many other industries’
developments, such as tourism, freighting and shipping businesses,
just to mention a few. However, it seems that their previous
transportation planning in the due course has failed to meet the fast
growing demand. As with the span of time, both the countries are
looking forward to a long-term, and economical solutions, because
the demand is from time to time keep appreciating and reacting
according to other key economic drivers. Content analysis method
and case study approach is used in this paper and secondary data
from the bureau of statistic is used for case analysis. The paper
focused on the mobility concerns of the lower and middle-income
people in India and Pakistan. The paper is aimed to highlight the
weaknesses, opportunities and limitations resulting from low priority
industry for a government, which is making the either country's
public suffer. The paper has concluded that the main issue is
identified as the slow, inappropriate, and unfavorable decisions which
are not in favor of long-term country’s economic development and
public interest. The paper also recommends to future research
avenues for public and private transportation, which is continuously
failing to meet the public expectations.
Abstract: A theoretical study of a humidification
dehumidification solar desalination unit has been carried out to
increase understanding the effect of weather conditions on the unit
productivity. A humidification-dehumidification (HD) solar
desalination unit has been designed to provide fresh water for
population in remote arid areas. It consists of solar water collector
and air collector; to provide the hot water and air to the desalination
chamber. The desalination chamber is divided into humidification
and dehumidification towers. The circulation of air between the two
towers is maintained by the forced convection. A mathematical
model has been formulated, in which the thermodynamic relations
were used to study the flow, heat and mass transfer inside the
humidifier and dehumidifier. The present technique is performed in
order to increase the unit performance. Heat and mass balance has
been done and a set of governing equations has been solved using the
finite difference technique. The unit productivity has been calculated
along the working day during the summer and winter sessions and
has compared with the available experimental results. The average
accumulative productivity of the system in winter has been ranged
between 2.5 to 4 (kg/m2)/day, while the average summer productivity
has been found between 8 to 12 (kg/m2)/day.
Abstract: To maintain a healthy balanced loyalty, whether to art
or society, posits a debatable issue. The artist is always on the look
out for the potential tension between those two realms. Therefore,
one of the most painful dilemmas the artist finds is how to function in
a society without sacrificing the aesthetic values of his/her work. In
other words, the life-long awareness of failure which derives from the
concept of the artist as caught between unflattering social realities
and the need to invent genuine art forms becomes a fertilizing soil for
the artists to be tackled. Thus, within the framework of this dilemma,
the question of the responsibility of the artist and the relationship of
the art to politics will be illuminating. To a larger extent, however, in
drama, this dilemma is represented by the fictional characters of the
play. The present paper tackles the idea of the amorality of the artist in
selected plays by Tom Stoppard. However, Stoppard’s awareness of
his situation as a refugee has led him to keep at a distance from
politics. He tried hard to avoid any intervention into the realms of
political debate, especially in his earliest work. On the one hand, it is
not meant that he did not interest in politics as such, but rather he
preferred to question it than to create a fixed ideological position. On
the other hand, Stoppard’s refusal to intervene in politics is ascribed
to his feeling of gratitude to Britain where he settled. As a result,
Stoppard has frequently been criticized for a lack of political
engagement and also for not leaning too much for the left when he
does engage. His reaction to these public criticisms finds expression
in his self-conscious statements which defensively stressed the
artifice of his work. He, like Oscar Wilde thinks that the
responsibility of the artist is devoted to the realm of his/her art.
Consequently, his consciousness for the role of the artist is truly
reflected in his two plays, Artist Descending a Staircase (1972) and
Travesties (1974).
Abstract: In this paper, we calculate the two-photon ionization
(TPI) cross-section for pump-probe scheme in Ag neutral cluster. The
pump photon energy is assumed to be close to the surface plasmon
(SP) energy of cluster in dielectric media. Due to this choice, the
pump wave excites collective oscillations of electrons-SP and the
probe wave causes ionization of the cluster. Since the interband
transition energy in Ag exceeds the SP resonance energy, the main
contribution into the TPI comes from the latter. The advantage of Ag
clusters as compared to the other noble metals is that the SP
resonance in silver cluster is much sharper because of peculiarities of
its dielectric function. The calculations are performed by separating
the coordinates of electrons corresponding to the collective
oscillations and the individual motion that allows taking into account
the resonance contribution of excited SP oscillations. It is shown that
the ionization cross section increases by two orders of magnitude if
the energy of the pump photon matches the surface plasmon energy
in the cluster.
Abstract: Background: Breast milk may impact early brain
development, with potentially important biological, medical and
social implications. There is an important discussion on which is the
adequate breastfeeding extension to the development consolidation
and how the children breastfeeding affects their psychomotor
development, in the first year of life, and in following periods as
well. Some special fats (LC PUFA) contained in breast milk play a
key role in the brain’s maturation and cognitive development or
social skills. These capacities created during breastfeeding time
would be unfolded throughout all lifespan. Aim of the study: In our research, we have studied the effect of
breastfeeding in preschooler's psychomotor assessment.
Method: This study was conducted in a sample of 158 preschool
children in Vlorë, Albania. We have measured the psychometric
parameters of preschoolers with ASQ-3 (Age&Stage Questionnaires-
3). The studied sample was divided in three groups according to their
breastfeeding duration (3, 6 and 12 months). Results: Children breastfed for only 3 months have definitely
lower psychometric scores compared to the ones with 6 or more
months of breastfeeding (respectively 217 to 239 ASQ-3 scores). Six
and twelvemonth breastfed children have progressively more odds to
have high levels of psychomotor development comparing to those
with only 3 months of breastfeeding. The most affected psychometric
domains by shortness of breastfeeding are Communication and
Global motor. Conclusion: This leads to conclusion that to ensure high
psychomotor parameters during childhood is necessary breastfeeding
for at least 6 months.