Abstract: Synchrophasor technology is fast being deployed in
electric power grids all over the world and is fast changing the way
the grids are managed. This trend is to continue until the entire
power grids are fully connected so they can be monitored and
controlled in real-time. Much achievement has been made in the
synchrophasor technology development and deployment, and there
are still much more to be achieved. For instance, real-time power
grid control and protection potentials of synchrophasor are yet to be
explored. It is of necessity that researchers keep in view the various
challenges that still need to be overcome in expanding the frontiers
of synchrophasor technology. This paper outlines the major
challenges that should be dealt with in order to achieve the goal of
total power grid visualization, monitoring, and control using
synchrophasor technology.
Abstract: NiFe2O4 (nickel ferrite), ZnFe2O4 (zinc ferrite) and
Ni0.5Zn0.5Fe2O4 (nickel-zinc ferrite) were prepared by
mechanochemical route in a planetary ball mill starting from mixture
of the appropriate quantities of the Ni(OH)2/Fe(OH)3,
Zn(OH)2/Fe(OH)3 and Ni(OH)2/Zn(OH)2/Fe(OH)3 hydroxide
powders. In order to monitor the progress of chemical reaction and
confirm phase formation, powder samples obtained after 25 h, 18 h
and 10 h of milling were characterized by X-ray diffraction (XRD),
transmission electron microscopy (TEM), IR, Raman and Mössbauer
spectroscopy. It is shown that the soft mechanochemical method, i.e.
mechanochemical activation of hydroxides, produces high quality
single phase ferrite samples in much more efficient way. From the IR
spectroscopy of single phase samples it is obvious that energy of
modes depends on the ratio of cations. It is obvious that all samples
have more than 5 Raman active modes predicted by group theory in
the normal spinel structure. Deconvolution of measured spectra
allows one to conclude that all complex bands in the spectra are made
of individual peaks with the intensities that vary from spectrum to
spectrum. The deconvolution of Raman spectra allows to separate
contributions of different cations to a particular type of vibration and
to estimate the degree of inversion.
Abstract: From the start, the importance of having a plan to
sustain tourism was acknowledged. The correct methods to monitor
that type of tourism have been researched. Thus, we propose in this
work to analyze the applicability of a monitoring and assistance
method on the understanding of the tourism sustainability in a small
size destiny or getaway. In this study, the subject is Lagoa da
Confusão, in the state of Tocantins and the analysis was carried out
through the efficiency of the local indicators, according to the WOT
approach. We concluded that the sustainable tourism key points that
were analyzed demonstrated to be important evaluation and
quantification tools for the proposed tasks to be developed in the
mentioned destiny. This is a study of an interdisciplinary character
and the deductive method was chosen as the guiding line.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: Analytical techniques for measuring and planning
railway capacity expansion activities have been considered in this
article. A preliminary mathematical framework involving track
duplication and section sub divisions is proposed for this task. In
railways, these features have a great effect on network performance
and for this reason they have been considered. Additional motivations
have also arisen from the limitations of prior models that have not
included them.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.
Abstract: The high-molecular water-soluble preparations from
several species of two genera (Symphytum and Anchusa) of
Boraginaceae family Symphytum asperum, S. caucasicum, S.officinale
and Anchusa italica were isolated. According to IR, 13C and 1H
NMR, APT, 1D NOE, 2D heteronuclear 1H/13C HSQC and 2D
DOSY experiments, the main chemical constituent of these
preparations was found to be caffeic acid-derived polyether, namely
poly[3-(3,4-dihydroxyphenyl)glyceric acid] (PDPGA) or poly[oxy-1-
carboxy-2-(3,4-dihydroxyphenyl)ethylene]. Most carboxylic groups
of this caffeic acid-derived polymer of A. italica are methylated.
Abstract: High moisture content in fruits generates post-harvest
problems such as mechanical, biochemical, microbial and physical
losses. Dehydration, which is based on the reduction of water activity
of the fruit, is a common option for overcoming such losses.
However, regular hot air drying could affect negatively the quality
properties of the fruit due to the long residence time at high
temperature. Power ultrasound (US) application during the
convective drying has been used as a novel method able to enhance
drying rate and, consequently, to decrease drying time. In the present
study, a new approach was tested to evaluate the effect of US on the
drying time, the final antioxidant activity (AA) and the total
polyphenol content (TPC) of banana slices (BS), mango slices (MS)
and guava slices (GS). There were also studied the drying kinetics
with nine different models from which water effective diffusivities
(Deff) (with or without shrinkage corrections) were calculated.
Compared with the corresponding control tests, US assisted drying
for fruit slices showed reductions in drying time between 16.23 and
30.19%, 11.34 and 32.73%, and 19.25 and 47.51% for the MS, BS
and GS respectively. Considering shrinkage effects, Deff calculated
values ranged from 1.67*10-10 to 3.18*10-10 m2/s, 3.96*10-10 and
5.57*10-10 m2/s and 4.61*10-10 to 8.16*10-10 m2/s for the BS, MS and
GS samples respectively. Reductions of TPC and AA (as DPPH)
were observed compared with the original content in fresh fruit data
in all kinds of drying assays.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: This paper studies a mathematical model based on the
integral equations for dynamic analyzes numerical investigations of a
non-uniform or multi-material composite beam. The beam is
subjected to a sub-tangential follower force and elastic foundation.
The boundary conditions are represented by generalized
parameterized fixations by the linear and rotary springs. A
mathematical formula based on Euler-Bernoulli beam theory is
presented for beams with variable cross-sections. The non-uniform
section introduces non-uniformity in the rigidity and inertia of beams
and consequently, more complicated equilibrium who governs the
equation. Using the boundary element method and radial basis
functions, the equation of motion is reduced to an algebro-differential
system related to internal and boundary unknowns. A generalized
formula for the deflection, the slope, the moment and the shear force
are presented. The free vibration of non-uniform loaded beams is
formulated in a compact matrix form and all needed matrices are
explicitly given. The dynamic stability analysis of slender beam is
illustrated numerically based on the coalescence criterion. A realistic
case related to an industrial chimney is investigated.
Abstract: Asphalt concrete pavements have a short life cycle,
failing mainly due to temperature changes, traffic loading and ageing.
Modified asphalt mixtures provide the technology to produce a
bituminous binder with improved viscoelastic properties, which
remain in balance over a wider temperature range and loading
conditions. In this research, 60/70 penetration grade asphalt binder
was modified by adding 2, 4, 6, 8 and 10 percent by weight of asphalt
binder following the wet process and the mineral aggregate was
modified by adding 1, 2, 3, 4 and 5 percent crumb rubber by volume
of the mineral aggregate following the dry process. The LDPE
modified asphalt binder rheological properties were evaluated. The
laboratory results showed an increase in viscosity, softening point
and stiffness of the binder. The modified asphalt was then used in
preparing asphalt mixtures by Marshall Mix design procedure. The
Marshall Stability values for mixes containing 2% crumb rubber and
4% LDPE were found to be 30% higher than the conventional asphalt
concrete mix.
Abstract: Target of this study was the analysis of the impact of
crude glycerol on canine spermatozoa motility, morphology,
viability, and membrane integrity. Experiments were realized in vitro.
In the study, semen from 5 large dog breeds was used. They were
typical representatives of large breeds, coming from healthy rearing,
regularly vaccinated and integrated to the further breeding. Semen
collections were realized at the owners of animals and in the
veterinary clinic. Subsequently the experiments were realized at the
Department of Animal Physiology of the SUA in Nitra. The
spermatozoa motility was evaluated using CASA analyzer
(SpermVisionTM, Minitub, Germany) at the temperature 5 and 37°C
for 5 hours. In the study, 13 motility parameters were evaluated.
Generally, crude glycerol has generally negative effect on
spermatozoa motility. Morphological analysis was realized using
Hancock staining and the preparations were evaluated at
magnification 1000x using classification tables of morphologically
changed spermatozoa. Data clearly detected the highest number of
morphologically changed spermatozoa in the experimental groups
(know twisted tails, tail torso and tail coiling). For acrosome
alterations swelled acrosomes, removed acrosomes and acrosomes
with undulated membrane were detected. In this study also the effect
of crude glycerol on spermatozoa membrane integrity were analyzed.
The highest crude glycerol concentration significantly affects
spermatozoa integrity. Results of this study show that crude glycerol
has effect of spermatozoa motility, viability, and membrane integrity.
Detected changes are related to crude glycerol concentration,
temperature, as well as time of incubation.
Abstract: In view of the requirements of the current industrial
processes, the instrumentation plays a critical role. In this context,
this work aims to raise some the operating characteristics of the level
and flow transmitters, in addition to observing their similarities and
possible limitations configurations.
Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.
Abstract: The aim of this study was to investigate the
photocatalytic activity of polycrystalline phases of bismuth tungstate
of formula Bi2WO6. Polycrystalline samples were elaborated using a
coprecipitation technique followed by a calcination process at
different temperatures (300, 400, 600 and 900°C). The obtained
polycrystalline phases have been characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), and transmission
electron microscopy (TEM). Crystal cell parameters and cell volume
depend on elaboration temperature. High-resolution electron
microscopy images and image simulations, associated with X-ray
diffraction data, allowed confirming the lattices and space groups
Pca21. The photocatalytic activity of the as-prepared samples was
studied by irradiating aqueous solutions of Rhodamine B, associated
with Bi2WO6 additives having variable crystallite sizes. The
photocatalytic activity of such bismuth tungstates increased as the
crystallite sizes decreased. The high specific area of the
photocatalytic particles obtained at 300°C seems to condition the
degradation kinetics of RhB.
Abstract: The purpose of this research was to investigate the
creep behaviour of the heterogeneous Timber-UHPFRC beams. New
developments have been done to further improve the structural
performance, such as strengthening of the timber (glulam) beam by
bonding composite material combine with an ultra-high performance
fibre reinforced concrete (UHPFRC) internally reinforced with or
without carbon fibre reinforced polymer (CFRP) bars. However, in
the design of wooden structures, in addition to the criteria of
strengthening and stiffness, deformability due to the creep of wood,
especially in horizontal elements, is also a design criterion. Glulam,
UHPFRC and CFRP may be an interesting composite mix to respond
to the issue of creep behaviour of composite structures made of
different materials with different rheological properties. In this paper,
we describe an experimental and analytical investigation of the creep
performance of the glulam-UHPFRC-CFRP beams assembled by
bonding. The experimental investigations creep behaviour was
conducted for different environments: in- and outside under constant
loading for approximately a year. The measured results are compared
with numerical ones obtained by an analytical model. This model was
developed to predict the creep response of the glulam-UHPFRCCFRP
beams based on the creep characteristics of the individual
components. The results show that heterogeneous glulam-UHPFRC
beams provide an improvement in both the strengthening and
stiffness, and can also effectively reduce the creep deflection of
wooden beams.
Abstract: In this paper, synchronization of multiple chaotic
semiconductor lasers is achieved by appealing to complex system
theory. In particular, we consider dynamical networks composed by
semiconductor laser, as interconnected nodes, where the interaction
in the networks are defined by coupling the first state of each node.
An interest case is synchronized with master-slave configuration in
star topology. Nodes of these networks are modeled for the laser and
simulate by Matlab. These results are applicable to private
communication.
Abstract: The availability to deploy mobile applications for
health care is increasing daily thru different mobile app stores. But
within these capabilities the number of hacking attacks has also
increased, in particular into medical mobile applications. The security
vulnerabilities in medical mobile apps can be triggered by errors in
code, incorrect logic, poor design, among other parameters. This is
usually used by malicious attackers to steal or modify the users’
information. The aim of this research is to analyze the vulnerabilities
detected in mobile medical apps according to risk factor standards
defined by OWASP in 2014.
Abstract: Objective: Sharing devastating news with patients is
often considered the most difficult task of doctors. This study aimed
to explore patients’ perceptions of receiving bad news including
which features improve the experience and which areas need refining. Methods: A questionnaire was written based on the steps of the
SPIKES model for breaking bad new. 20 patients receiving treatment
for a hematological malignancy completed the questionnaire. Results: Overall, the results are promising as most patients praised
their consultation. ‘Poor’ was more commonly rated by women and
participants aged 45-64. The main differences between the ‘excellent’
and ‘poor’ consultations include the doctor’s sensitivity and checking
the patients’ understanding. Only 35% of patients were asked their
existing knowledge and 85% of consultations failed to discuss the
impact of the diagnosis on daily life. Conclusion: This study agreed with the consensus of existing
literature. The commended aspects include consultation set-up and
information given. Areas patients felt needed improvement include
doctors determining the patient’s existing knowledge and checking
new information has been understood. Doctors should also explore
how the diagnosis will affect the patient’s life. With a poorer
prognosis, doctors should work on conveying appropriate hope. The
study was limited by a small sample size and potential recall bias.
Abstract: Linear stability analysis of double diffusive convection
in a horizontal porous layer saturated with fluid is examined by
considering the effects of viscous dissipation, concentration based
internal heat source and vertical throughflow. The basic steady
state solution for Governing equations is derived. Linear stability
analysis has been implemented numerically by using shooting
and Runge-kutta methods. Critical thermal Rayleigh number Rac
is obtained for various values of solutal Rayleigh number Sa,
vertical Peclet number Pe, Gebhart number Ge, Lewis number
Le and measure of concentration based internal heat source
γ. It is observed that Ge has destabilizing effect for upward
throughflow and stabilizing effect for downward throughflow. And
γ has considerable destabilizing effect for upward throughflow and
insignificant destabilizing effect for downward throughflow.