Abstract: The effect of different tempering temperatures and heat treatment times on the corrosion resistance of austenitic stainless steels in oxalic acid was studied in this work using conventional weight loss and electrochemical measurements. Typical 304 and 316 stainless steel samples were tempered at 150oC, 250oC and 350oC after being austenized at 1050oC for 10 minutes. These samples were then immersed in 1.0M oxalic acid and their weight losses were measured at every five days for 30 days. The results show that corrosion of both types of ASS samples increased with an increase in tempering temperature and time and this was due to the precipitation of chromium carbides at the grain boundaries of these metals. Electrochemical results also confirm that the 304 ASS is more susceptible to corrosion than 316 ASS in this medium. This is attributed to the molybdenum in the composition of the latter. The metallographic images of these samples showed non–uniform distribution of precipitated chromium carbides at the grain boundaries of these metals and unevenly distributed carbides and retained austenite phases which cause galvanic effects in the medium.
Abstract: In Thailand, the practice of pre-hospital Emergency
Medical Service (EMS) in each area reveals the different growth
rates and effectiveness of the practices. Those can be found as the
diverse quality and quantity. To shorten the learning curve prior to
speed-up the practices in other areas, story telling and lessons learnt
from the effective practices are valued as meaningful knowledge. To
this paper, it was to ascertain the factors, lessons learnt and best
practices that have impact as contributing to the success of prehospital
EMS system. Those were formulized as model prior to
speedup the practice in other areas. To develop the model, Malcolm
Baldrige National Quality Award (MBNQA), which is widely
recognized as a framework for organizational quality assessment and
improvement, was chosen as the discussion framework. Remarkably,
this study was based on the consideration of knowledge capture;
however it was not to complete the loop of knowledge activities.
Nevertheless, it was to highlight the recognition of knowledge
capture, which is the initiation of knowledge management.
Abstract: The paper studies implications between knowledge spillovers and technological innovation capability in the following three aspects: firstly, the paper debates on the effect of knowledge spillover on some perspectives of technological innovation ability; secondly, it discusses how different roles of knowledge spillover affect the technological innovation capability; finally, the paper creates the model of the factors of knowledge spillovers influencing to technological innovation capability. It concludes that knowledge spillovers affect all the main aspects of technological innovation ultimately to impact of technological innovation capabilities.
Abstract: Void formation in underfill is considered as failure
in flip chip manufacturing process. Void formation possibly caused
by several factors such as poor soldering and flux residue during
die attach process, void entrapment due moisture contamination,
dispense pattern process and setting up the curing process. This
paper presents the comparison of single step and two steps curing
profile towards the void and black dots formation in underfill for
Hi-CTE Flip Chip Ceramic Ball Grid Array Package (FC-CBGA).
Statistic analysis was conducted to analyze how different factors
such as wafer lot, sawing technique, underfill fillet height and
curing profile recipe were affected the formation of voids and
black dots. A C-Mode Scanning Aqoustic Microscopy (C-SAM)
was used to scan the total count of voids and black dots. It was
shown that the 2 steps curing profile provided solution for void
elimination and black dots in underfill after curing process.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: The most widely used semiconductor memory types
are the Dynamic Random Access Memory (DRAM) and Static
Random Access memory (SRAM). Competition among memory
manufacturers drives the need to decrease power consumption and
reduce the probability of read failure. A technology that is relatively
new and has not been explored is the FinFET technology. In this
paper, a single cell Schmitt Trigger Based Static RAM using FinFET
technology is proposed and analyzed. The accuracy of the result is
validated by means of HSPICE simulations with 32nm FinFET
technology and the results are then compared with 6T SRAM using
the same technology.
Abstract: As communications systems and technology become more advanced and complex, it will be increasingly important to focus on users- individual needs. Personalization and effective user profile management will be necessary to ensure the uptake and success of new services and devices and it is therefore important to focus on the users- requirements in this area and define solutions that meet these requirements. The work on personalization and user profiles emerged from earlier ETSI work on a Universal Communications Identifier (UCI) which is a unique identifier of the user rather than a range of identifiers of the many of communication devices or services (e.g. numbers of fixed phone at home/work, mobile phones, fax and email addresses). This paper describes work on personalization including standardized information and preferences and an architectural framework providing a description of how personalization can be integrated in Next Generation Networks, together with the UCI concept.
Abstract: In this paper a nonlinear model is presented to
demonstrate the relation between production and marketing
departments. By introducing some functions such as pricing cost and
market share loss functions it will be tried to show some aspects of
market modelling which has not been regarded before. The proposed
model will be a constrained signomial geometric programming
model. For model solving, after variables- modifications an iterative
technique based on the concept of geometric mean will be introduced
to solve the resulting non-standard posynomial model which can be
applied to a wide variety of models in non-standard posynomial
geometric programming form. At the end a numerical analysis will
be presented to accredit the validity of the mentioned model.
Abstract: Existing experiences indicate that one of the most
prominent reasons that some ERP implementations fail is related to
selecting an improper ERP package. Among those important factors
resulting in inappropriate ERP selections, one is to ignore preliminary
activities that should be done before the evaluation of ERP packages.
Another factor yielding these unsuitable selections is that usually
organizations employ prolonged and costly selection processes in
such extent that sometimes the process would never be finalized
or sometimes the evaluation team might perform many key final
activities in an incomplete or inaccurate way due to exhaustion, lack
of interest or out-of-date data. In this paper, a systematic approach
that recommends some activities to be done before and after the
main selection phase is introduced for choosing an ERP package. On
the other hand, the proposed approach has utilized some ideas that
accelerates the selection process at the same time that reduces the
probability of an erroneous final selection.
Abstract: A new method for low complexity image coding is presented, that permits different settings and great scalability in the generation of the final bit stream. This coding presents a continuoustone still image compression system that groups loss and lossless compression making use of finite arithmetic reversible transforms. Both transformation in the space of color and wavelet transformation are reversible. The transformed coefficients are coded by means of a coding system in depending on a subdivision into smaller components (CFDS) similar to the bit importance codification. The subcomponents so obtained are reordered by means of a highly configure alignment system depending on the application that makes possible the re-configure of the elements of the image and obtaining different levels of importance from which the bit stream will be generated. The subcomponents of each level of importance are coded using a variable length entropy coding system (VBLm) that permits the generation of an embedded bit stream. This bit stream supposes itself a bit stream that codes a compressed still image. However, the use of a packing system on the bit stream after the VBLm allows the realization of a final highly scalable bit stream from a basic image level and one or several enhance levels.
Abstract: We present a dextran modified silicon microring
resonator sensor for high density antibody immobilization. An array
of sensors consisting of three sensor rings and a reference ring was
fabricated and its surface sensitivity and the limit of detection were
obtained using polyelectrolyte multilayers. The mass sensitivity and
the limit of detection of the fabricated sensor ring are 0.35 nm/ng
mm-2 and 42.8 pg/mm2 in air, respectively. Dextran modified sensor
surface was successfully prepared by covalent grafting of oxidized
dextran on 3-aminopropyltriethoxysilane (APTES) modified silicon
sensor surface. The antibody immobilization on hydrogel dextran
matrix improves 40% compared to traditional antibody
immobilization method via APTES and glutaraldehyde linkage.
Abstract: This paper presents a vocoder to obtain high quality synthetic speech at 600 bps. To reduce the bit rate, the algorithm is based on a sinusoidally excited linear prediction model which extracts few coding parameters, and three consecutive frames are grouped into a superframe and jointly vector quantization is used to obtain high coding efficiency. The inter-frame redundancy is exploited with distinct quantization schemes for different unvoiced/voiced frame combinations in the superframe. Experimental results show that the quality of the proposed coder is better than that of 2.4kbps LPC10e and achieves approximately the same as that of 2.4kbps MELP and with high robustness.
Abstract: In this paper, collocation based cubic B-spline and
extended cubic uniform B-spline method are considered for
solving one-dimensional heat equation with a nonlocal initial
condition. Finite difference and θ-weighted scheme is used for
time and space discretization respectively. The stability of the
method is analyzed by the Von Neumann method. Accuracy of
the methods is illustrated with an example. The numerical results
are obtained and compared with the analytical solutions.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: A straightforward and intuitive combination of single simulations into an aggregated master-simulation is not trivial. There are lots of problems, which trigger-specific difficulties during the modeling and execution of such a simulation. In this paper we identify these problems and aim to solve them by mapping the task to the field of multi agent systems. The solution is a new meta-model named AGENTMAP, which is able to mitigate most of the problems and to support intuitive modeling at the same time. This meta-model will be introduced and explained on basis of an example from the e-commerce domain.
Abstract: The batch nature limits the standard kernel principal component analysis (KPCA) methods in numerous applications, especially for dynamic or large-scale data. In this paper, an efficient adaptive approach is presented for online extraction of the kernel principal components (KPC). The contribution of this paper may be divided into two parts. First, kernel covariance matrix is correctly updated to adapt to the changing characteristics of data. Second, KPC are recursively formulated to overcome the batch nature of standard KPCA.This formulation is derived from the recursive eigen-decomposition of kernel covariance matrix and indicates the KPC variation caused by the new data. The proposed method not only alleviates sub-optimality of the KPCA method for non-stationary data, but also maintains constant update speed and memory usage as the data-size increases. Experiments for simulation data and real applications demonstrate that our approach yields improvements in terms of both computational speed and approximation accuracy.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: Collateralized Debt Obligations are not as widely used
nowadays as they were before 2007 Subprime crisis. Nonetheless
there remains an enthralling challenge to optimize cash flows
associated with synthetic CDOs. A Gaussian-based model is used
here in which default correlation and unconditional probabilities of
default are highlighted. Then numerous simulations are performed
based on this model for different scenarios in order to evaluate the
associated cash flows given a specific number of defaults at different
periods of time. Cash flows are not solely calculated on a single
bought or sold tranche but rather on a combination of bought and
sold tranches. With some assumptions, the simplex algorithm gives
a way to find the maximum cash flow according to correlation of
defaults and maturities. The used Gaussian model is not realistic in
crisis situations. Besides present system does not handle buying or
selling a portion of a tranche but only the whole tranche. However the
work provides the investor with relevant elements on how to know
what and when to buy and sell.
Abstract: CDMA cellular networks support soft handover,
which guarantees the continuity of wireless services and enhanced
communication quality. Cellular networks support multimedia
services under varied propagation environmental conditions. In this
paper, we have shown the effect of characteristic parameters of the
cellular environments on the soft handover performance. We
consider path loss exponent, standard deviation of shadow fading and
correlation coefficient of shadow fading as the characteristic
parameters of the radio propagation environment. A very useful
statistical measure for characterizing the performance of mobile radio
system is the probability of outage. It is shown through numerical
results that above parameters have decisive effect on the probability
of outage and hence the overall performance of the soft handover
algorithm.
Abstract: This paper presents a method to detect multiple cracks
based on frequency information. When a structure is subjected to
dynamic or static loads, cracks may develop and the modal
frequencies of the cracked structure may change. To detect cracks in a
structure, we construct a high precision wavelet finite element (EF)
model of a certain structure using the B-spline wavelet on the interval
(BSWI). Cracks can be modeled by rotational springs and added to the
FE model. The crack detection database will be obtained by solving
that model. Then the crack locations and depths can be determined
based on the frequency information from the database. The
performance of the proposed method has been numerically verified by
a rotor example.