Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: Direct numerical simulation (DNS) is used to study the evolution of a boundary layer that was laminar initially followed by separation and then reattachment owing to generation of turbulence. This creates a closed region of recirculation, known as the laminar-separation bubble. The present simulation emulates the flow environment encountered in a modern LP turbine blade, where a laminar separation bubble may occur on the suction surface. The unsteady, incompressible three-dimensional (3-D) Navier-Stokes (NS) equations have been solved over a flat plate in the Cartesian coordinates. The adverse pressure gradient, which causes the flow to separate, is created by a boundary condition. The separated shear layer undergoes transition through appearance of ╬ø vortices, stretching of these create longitudinal streaks. Breakdown of the streaks into small and irregular structures makes the flow turbulent downstream.
Abstract: In this paper, we proposed a novel receiver algorithm
for coherent underwater acoustic communications. The proposed
receiver is composed of three parts: (1) Doppler tracking and
correction, (2) Time reversal channel estimation and combining, and
(3) Joint iterative equalization and decoding (JIED). To reduce
computational complexity and optimize the equalization algorithm,
Time reversal (TR) channel estimation and combining is adopted to
simplify multi-channel adaptive decision feedback equalizer (ADFE)
into single channel ADFE without reducing the system performance.
Simultaneously, the turbo theory is adopted to form joint iterative
ADFE and convolutional decoder (JIED). In JIED scheme, the ADFE
and decoder exchange soft information in an iterative manner, which
can enhance the equalizer performance using decoding gain. The
simulation results show that the proposed algorithm can reduce
computational complexity and improve the performance of equalizer.
Therefore, the performance of coherent underwater acoustic
communications can be improved greatly.
Abstract: In this paper we discuss on the security module for the
car appliances to prevent stealing and illegal use on other cars. We
proposed an open structure including authentication and encryption by
embed a security module in each to protect car appliances. Illegal
moving and use a car appliance with the security module without
permission will lead the appliance to useless. This paper also presents
the component identification and deal with relevant procedures. It is at
low cost to recover from destroys by the burglar. Expect this paper to
offer the new business opportunity to the automotive and technology
industry.
Abstract: A spatial classification technique incorporating a State of Art Feature Extraction algorithm is proposed in this paper for classifying a heterogeneous classes present in hyper spectral images. The classification accuracy can be improved if and only if both the feature extraction and classifier selection are proper. As the classes in the hyper spectral images are assumed to have different textures, textural classification is entertained. Run Length feature extraction is entailed along with the Principal Components and Independent Components. A Hyperspectral Image of Indiana Site taken by AVIRIS is inducted for the experiment. Among the original 220 bands, a subset of 120 bands is selected. Gray Level Run Length Matrix (GLRLM) is calculated for the selected forty bands. From GLRLMs the Run Length features for individual pixels are calculated. The Principle Components are calculated for other forty bands. Independent Components are calculated for next forty bands. As Principal & Independent Components have the ability to represent the textural content of pixels, they are treated as features. The summation of Run Length features, Principal Components, and Independent Components forms the Combined Features which are used for classification. SVM with Binary Hierarchical Tree is used to classify the hyper spectral image. Results are validated with ground truth and accuracies are calculated.
Abstract: We introduce a novel approach to measuring how
humans learn based on techniques from information theory and
apply it to the oriental game of Go. We show that the total amount
of information observable in human strategies, called the strategic
information, remains constant for populations of players of differing
skill levels for well studied patterns of play. This is despite the very
large amount of knowledge required to progress from the recreational
players at one end of our spectrum to the very best and most
experienced players in the world at the other and is in contrast to
the idea that having more knowledge might imply more 'certainty'
in what move to play next. We show this is true for very local
up to medium sized board patterns, across a variety of different
moves using 80,000 game records. Consequences for theoretical and
practical AI are outlined.
Abstract: The construction industry is the pillar industry in
China, accounting for about 6% of the gross domestic product. Along
with changes in the external environment of the construction industry
in China, the construction firm faces fierce competition. The paper
aims to investigate the relationship between diversified types of
construction firm and its performance in China. Based on generalist
and specialist strategy in organizational ecology, we think a generalist
organization can be applied to an enterprise with diversified
developments, while specialist groups are extended to professional
enterprises .This study takes advantage of annual financial data of
listed construction firm to empirically verify the relationship between
diversification and corporation performance establishing a regression
equation to econometric analysis. We find that: 1) Specialization can
significantly improve the level of profitability of listed construction
firms, and there is a significant positive relationship with corporate
performance; 2) The level of operating performance of listed
construction enterprises which engage in unrelated diversification is
higher than those with related diversification; 3) The relationship
between state-owned construction firms and corporate performance is
negative. The more the year of foundation is, the higher performance
will be; however, the more the year of being listed, the lower
performance will be.
Abstract: This study proposes and tests a rescapturing elements of perceived gain and loss that, by perceived value of medical tourism products, influencintention of potential customers. Data from 301 usable qwere tested against the research model using the structmodeling approach. The results indicated that perceivedkey predictor of customer intentions. As for benefimedical quality, service quality and enjoyment wcomponents that significantly influenced the perceptiRegarding sacrifice, the effects of perceived risk on pewere significant. The findings can provide insights intohow destination countries can make medical tourism a wfor themselves and international patients.KeywordsMedical tourism, perceived valueintention.
Abstract: Multi-Agent Systems (MAS) emerged in the pursuit to improve our standard of living, and hence can manifest complex human behaviors such as communication, decision making, negotiation and self-organization. The Social Network Services (SNSs) have attracted millions of users, many of whom have integrated these sites into their daily practices. The domains of MAS and SNS have lots of similarities such as architecture, features and functions. Exploring social network users- behavior through multiagent model is therefore our research focus, in order to generate more accurate and meaningful information to SNS users. An application of MAS is the e-Auction and e-Rental services of the Universiti Cyber AgenT(UniCAT), a Social Network for students in Universiti Tunku Abdul Rahman (UTAR), Kampar, Malaysia, built around the Belief- Desire-Intention (BDI) model. However, in spite of the various advantages of the BDI model, it has also been discovered to have some shortcomings. This paper therefore proposes a multi-agent framework utilizing a modified BDI model- Belief-Desire-Intention in Dynamic and Uncertain Situations (BDIDUS), using UniCAT system as a case study.
Abstract: Reliability Centered Maintenance(RCM) is one of
most widely used methods in the modern power system to schedule a
maintenance cycle and determine the priority of inspection. In order
to apply the RCM method to the Smart Grid, a precedence study for
the new structure of rearranged system should be performed due to
introduction of additional installation such as renewable and
sustainable energy resources, energy storage devices and advanced
metering infrastructure. This paper proposes a new method to
evaluate the priority of maintenance and inspection of the power
system facilities in the Smart Grid using the Risk Priority Number. In
order to calculate that risk index, it is required that the reliability
block diagram should be analyzed for the Smart Grid system. Finally,
the feasible technical method is discussed to estimate the risk
potential as part of the RCM procedure.
Abstract: Grid computing provides a virtual framework for
controlled sharing of resources across institutional boundaries.
Recently, trust has been recognised as an important factor for
selection of optimal resources in a grid. We introduce a new method
that provides a quantitative trust value, based on the past interactions
and present environment characteristics. This quantitative trust value
is used to select a suitable resource for a job and eliminates run time
failures arising from incompatible user-resource pairs. The proposed
work will act as a tool to calculate the trust values of the various
components of the grid and there by improves the success rate of the
jobs submitted to the resource on the grid. The access to a resource
not only depend on the identity and behaviour of the resource but
also upon its context of transaction, time of transaction, connectivity
bandwidth, availability of the resource and load on the resource. The
quality of the recommender is also evaluated based on the accuracy
of the feedback provided about a resource. The jobs are submitted for
execution to the selected resource after finding the overall trust value
of the resource. The overall trust value is computed with respect to
the subjective and objective parameters.
Abstract: Although White LED lighting systems powered by solar cells have presented for many years, they are not widely used in today application because of their cost and low energy conversion efficiency. The proposed system use the dc power generated by fixed solar cells module to energize White LED light sources that are operated by directly connected White LED with current limitation resistors, resulting in much more power consumption. This paper presents the use of white LED as a general lighting application powered by tracking solar cells module and using pulse to apply the electrical power to the White LED. These systems resulted in high efficiency power conversion, low power consumption, and long light of the white LED.
Abstract: The COSvd Ciphers has been proposed by Filiol and others (2004). It is a strengthened version of COS stream cipher family denoted COSvd that has been adopted for at least one commercial standard. We propose a distinguish attack on this version, and prove that, it is distinguishable from a random stream. In the COSvd Cipher used one S-Box (10×8) on the final part of cipher. We focus on S-Box and use weakness this S-Box for distinguish attack. In addition, found a leak on HNLL that the sub s-boxes don-t select uniformly. We use this property for an Improve distinguish attack.
Abstract: In this paper an ant colony optimization algorithm is
developed to solve the permutation flow shop scheduling problem. In
the permutation flow shop scheduling problem which has been vastly
studied in the literature, there are a set of m machines and a set of n
jobs. All the jobs are processed on all the machines and the sequence
of jobs being processed is the same on all the machines. Here this
problem is optimized considering two criteria, makespan and total
flow time. Then the results are compared with the ones obtained by
previously developed algorithms. Finally it is visible that our
proposed approach performs best among all other algorithms in the
literature.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: The world of wireless telecommunications is rapidly evolving. Technologies under research and development promise to deliver more services to more users in less time. This paper presents the emerging technologies helping wireless systems grow from where we are today into our visions of the future. This paper will cover the applications and characteristics of emerging wireless technologies: Wireless Local Area Networks (WiFi-802.11n), Wireless Personal Area Networks (ZigBee) and Wireless Metropolitan Area Networks (WiMAX). The purpose of this paper is to explain the impending 802.11n standard and how it will enable WLANs to support emerging media-rich applications. The paper will also detail how 802.11n compares with existing WLAN standards and offer strategies for users considering higher-bandwidth alternatives. The emerging IEEE 802.15.4 (ZigBee) standard aims to provide low data rate wireless communications with high-precision ranging and localization, by employing UWB technologies for a low-power and low cost solution. WiMAX (Worldwide Interoperability for Microwave Access) is a standard for wireless data transmission covering a range similar to cellular phone towers. With high performance in both distance and throughput, WiMAX technology could be a boon to current Internet providers seeking to become the leader of next generation wireless Internet access. This paper also explores how these emerging technologies differ from one another.
Abstract: The contact width is important design parameter for
optimizing the design of new metal gasket for asbestos substitution
gasket. The contact width is found have relationship with the helium
leak quantity. In the increasing of axial load value, the helium leak
quantity is decreasing and the contact width is increasing. This study
provides validity method using simulation analysis and the result is
compared to experimental using pressure sensitive paper. The results
denote similar trend data between simulation and experimental result.
Final evaluation is determined by helium leak quantity to check
leakage performance of gasket design. Considering the phenomena of
position change on the convex contact, it can be developed the
optimization of gasket design by increasing contact width.
Abstract: Emotion recognition is an important research field that finds lots of applications nowadays. This work emphasizes on recognizing different emotions from speech signal. The extracted features are related to statistics of pitch, formants, and energy contours, as well as spectral, perceptual and temporal features, jitter, and shimmer. The Artificial Neural Networks (ANN) was chosen as the classifier. Working on finding a robust and fast ANN classifier suitable for different real life application is our concern. Several experiments were carried out on different ANN to investigate the different factors that impact the classification success rate. Using a database containing 7 different emotions, it will be shown that with a proper and careful adjustment of features format, training data sorting, number of features selected and even the ANN type and architecture used, a success rate of 85% or even more can be achieved without increasing the system complicity and the computation time
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.